1 | ACDC Name/ID | Date updated | Last Edited By | Current location | Date stuffed | Ownership | Board type | FPGA | Oscillator | Power distribution type | SMAs Installed | Description of current working status (Evan-era) | Description of current working status (post Evan-era) | Current firmware installed | Shipping Hiistory | Modifications made | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
2 | ACDC 1 | 4/27/2022 | ??? | U. of C. | 125 MHz, D.Greenshields v (2/14) | ||||||||||||||||||||||||
3 | ACDC 2 | 7/25/2023 | Lab 6 Dark Room | 6/2014 | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | J2, J3, J4, J16, J17 | Un-tested/unknown | 25MHz 8b10b | |||||||||||||||||
4 | ACDC 3 | 9/3/2021 | U. of C. | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | J3, J4, J16, J17 | Chip 3 seems unresponsive from limited trials. The other chips can successfully digitize sine waves. | ACDC Firmware V3.04 | ||||||||||||||||||
5 | ACDC 4 | 4/27/2022 | ??? | 6/2014 | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | With 25MHz ACC, chips sample sin wave properly but based on the power cycle, one or two chips will only see noise out of cal-input | 25->40MHz firmware, .jic from ACDC10 | ||||||||||||||||||
6 | ACDC 5 | 9/1/2023 | Noah | Lab 6 Dark Room | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | Capacitor C670 fell of | shipped from ISU | ||||||||||||||||||
7 | ACDC 6 | 7/28/2023 | Jinseo | U. of C. MCP 106 | 6/2014 | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz (oscillator has been removed, 8/6/2021) | On-board linear regulators; MODIFIED option B+ | J2, J3, J4, J16, J17 | PSEC4_A is not sampling at all, PSEC4_D samples sometimes and not always, PSEC4_B and PSEC4_E are sampling at 25MHz buffer length and PSEC4_C looks good on all fronts | (6/30/2021) Testing in dark box so far going well. (8/6/2021) Capacitor and one PSEC chip were somehow damaged. Two caps and lin reg (+1.2V) were replaced but did not resolve issue -- concluded that it was PSEC chip (very warm to the touch). | D. Greenshields firmware v200 (5/27) | |||||||||||||||
8 | ACDC 9 | 4/27/2022 | U. of C. | ACDC Rev B 2014 | On-board linear regulators | ||||||||||||||||||||||||
9 | ACDC 7 | 10/22/2021 | U. of C. | 6/2014 | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | J2, J3, J16 | I suspect this FPGA is damaged | <-- that suspicion seems correct | ACDC Firmware V3.04 | ||||||||||||||||
10 | ACDC 8 | 9/3/2021 | U. of C. | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | J2, J3, J4, J16, J17 | Operational on all chips. Many corrupt buffer errors. | ACDC Firmware V3.04 | ||||||||||||||||||
11 | ACDC 10 | 8/18/2021 | U. of C. | 6/2014 | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | J2, J3, J16 | All chips sample well. Two channels on the chip farthest from the cal-input SMA have a few wonky samples that are consistently located relative to trigger sample. Chip 4 is sampling at a wierd data rate due to 25MHz clock from ACC. External trigger input J16 is "shot" and is in an "always true" state. | Have seen PSEC4 chips 1, 4, and 5 work properly, though as with ACDC 36, we suspect errors to be from the SMA to SAMTEC connectors and not the board. However, when running, there are significantly more corrupt buffer errors than on ACDC 36. | ACDC Firmware V3.04 | ||||||||||||||||
12 | ACDC 11 | 5/6/2022 | Sheffield | U. of C. | ACDC Rev B 2014 | ||||||||||||||||||||||||
13 | ACDC 20 | 7/25/2023 | Lab 6 Dark Room | 12/2017 | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz XLH536040 | On-board linear regulators | J2, J3, J4, J16 | 125 MHz 8b10b | ||||||||||||||||||
14 | ACDC 21 | 7/25/2023 | Lab 6 Dark Room | 12/2017 | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz XLH536041 | On-board linear regulators | Four chips read good data from an input sin wave, the chip second farthest from the cal-input sma samples at a rate different from the other chips but still samples the sin wave. Takes a few power cycles to get LVDS alignment | 25->40MHz firmware, .jic from ACDC10 | ||||||||||||||||||
15 | ACDC 22 | 7/25/2023 | Lab 6 Dark Room | 12/2017 | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz XLH536042 | On-board linear regulators | J2, J3, J4, J16 | Is not sampling correctly, needs to be tested for a more comprehensive description | 125 MHz 8b10b | |||||||||||||||||
16 | ACDC 23 | 4/27/2022 | Sciboone (depl. w/ LAPPD40) | 12/2017 | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz XLH536043 | On-board linear regulators; MODIFIED option B+ | (8/6/2021) Had a 25 MHz osc (maybe Evan needed to do some testing). We took the 40 MHz osc from ACDC 6 and swapped it in, but it didn't make the board work -- may have damaged osc during swap... (8/13/2021) Now has correct osc and removed a resistor; still unable to detect board. All 3 voltages are present... maybe FPGA or EEPROM issue? (8/15/2021) Missing a jumper connection at JP1! Connecting a jumper between the 2 pins closest to C37 makes it work now. | a3.10 | ||||||||||||||||||
17 | ACDC 24 | 10/14/2022 | Sciboone (depl. w/ LAPPD64) | 12/2017 | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz XLH536044 | On-board linear regulators; MODIFIED option B+ | All chips on all channels sample a sin wave well. Took four power cycles to get to this well working state. On third power cycle, readACDC calls were returning unstable values and data was very messy | (6/30/21) Flashed firmware successfully (need a different EEPROM number). (8/6/2021) Seems to be working the way we want. | D. Greenshields firmware v200 (5/27) (but with ACDC-compressed-EPCS64.jic file) | |||||||||||||||||
18 | ACDC 25 | 7/28/2023 | Jinseo | U. of C. MCP 106 | ANNIE | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators; MODIFIED option B+ | none | (6/30/2021) Testing in dark box is so far going well. (8/6/2021) Testing in dark box not going well. This board stopped taking data starting a few weeks ago. Now it cannot be flashed with firmware. | D. Greenshields firmware v200 (5/27) (may have a newer version but ppl aren't updating this sheet :P) | |||||||||||||||||
19 | ACDC 26 | 10/14/2022 | Lab 6 Dark Room | ANNIE | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | MODIFIED option B+ | none | (8/13/2021) Current draw is ~0.07A. Unable to flash firmware. (8/15/2021) A fuse was blown. Installing a working fuse makes the board work. | D. Greenshields firmware v200 (5/27) | ||||||||||||||||||
20 | ACDC 27 | 10/14/2022 | Sciboone (depl. w/ LAPPD63) | ANNIE | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | MODIFIED option B+ | none | (8/13/2021) Current draw is ~0.9A. Can be flashed with firmware, but is missing linear regulator for PSEC chips (U12). (8/15/2021) Installing a regulator at U12 makes the board work. | D. Greenshields firmware v200 (5/27) | ||||||||||||||||||
21 | ACDC 28 | 10/14/2022 | Sciboone (depl. w/ LAPPD64) | ANNIE | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | MODIFIED option B+ | none | D. Greenshields firmware v200 (5/27) | |||||||||||||||||||
22 | ACDC 29 | 1/28/2020 | Bernhard Adams | ANNIE | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | none | Have tried multiple power cycles and the board consistently has 100 mv noise on most of the channels. | 25MHz 8b10b | ||||||||||||||||||
23 | ACDC 30 | 4/27/2022 | Sciboone (depl. w/ LAPPD40) | ANNIE | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | MODIFIED option B+ | none | a3.10 | |||||||||||||||||||
24 | ACDC 31 | 10/14/2022 | Lab 6 Dark Room | ANNIE | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | MODIFIED option B+ | none | Have tested on noise and works well. Connects pretty consistently given a specific cabling configuration | a3.10 | ||||||||||||||||||
25 | ACDC 32 | 7/28/2023 | Jinseo | U. of C. MCP 106 | ANNIE | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | MODIFIED option B+ | none | Have tested on noise and works well. Connects pretty consistently given a specific cabling configuration | a3.10 | |||||||||||||||||
26 | ACDC 33 | 10/14/2022 | Sciboone (depl. w/ LAPPD63) | ANNIE | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators; MODIFIED option B+ | none | only LED 3 is on upon startup (and no other connections). With sof and jic of 25M acc 8b10b | (8/13/2021) Everything seems to be working fine. Data looks reasonable. | D. Greenshields firmware v200 (5/27) (installed 6/30/2021) | |||||||||||||||||
27 | ACDC 34 | 6/30/2021 | Warwick | ANNIE | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | J4 | Firmware from ejobe's last commit to ACDC firmware | shipped to Warwick UK | ||||||||||||||||||
28 | ACDC 35 | 10/14/2022 | Lab 6 Dark Room | ANNIE | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | MODIFIED option B+ | none | D. Greenshields firmware v200 (5/27) (installed 6/30/2021) | |||||||||||||||||||
29 | ACDC 36 | 8/18/2021 | U. of C. | ANNIE | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | none | can connect under no circumstances to acc-beta | Almost always runs with no corrupt buffer errors. Have seen all chips work on this board, but not all at once. Almost certain that all errors are due to SAMTEC to SMA connectors. Little evidence to suggest otherwise. | ACDC Firmware V3.04 | |||||||||||||||||
30 | ACDC 37 | 7/25/2023 | Lab 6 Dark Room | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | none | has new regulator, power block untested | 25MHz 8b10b | ||||||||||||||||||
31 | ACDC 38 | 6/30/2021 | Warwick | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | none | Issues loading firmware | 25MHz 8b10b | shipped to Warwick UK | |||||||||||||||||
32 | ACDC 39 | 8/18/2021 | U. of C. | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators, LT3083 | none | Currently is shorted somewhere near the power input | This board raises many corrupt buffer errors and cannot seem to calibrate effectively at all. | ACDC Firmware V3.04 | |||||||||||||||||
33 | ACDC 40 | 7/25/2023 | Lab 6 Dark Room | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | none | would not align LVDS with acc alpha; VV was working with this in the high bay | D. Greenshields firmware v (2/14) | ||||||||||||||||||
34 | ACDC 41 | 7/25/2023 | Lab 6 Dark Room | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | none | 25MHz 8b10b | |||||||||||||||||||
35 | ACDC 42 | 7/25/2023 | Lab 6 Dark Room | U. of C. | ACDC Rev B 2014 | Cyclone GX IV | 40MHz | On-board linear regulators | none | 25MHz 8b10b | |||||||||||||||||||
36 | ACDC 43 | 5/3/2024 | Cameron | U of C (MCP150) | 12/1/2019 | U. of C. test-beam | ACDC Rev C 2019 | Cyclone GX IV | No (2/22/24), regular clicking, bad PLL shape | ACDC Firmware V4.16 | R1, R4 are 24k; C104 C105 pulldowns present; ferrites present L8, L9, L11, L12 (power block inductors removed); but no other modifications | ||||||||||||||||||
37 | ACDC 44 | 5/3/2024 | Cameron | U of C (MCP150) | 12/1/2019 | U. of C. test-beam | ACDC Rev C 2019 | Cyclone GX IV | Power block inductors removed | No (2/22/24), draws only 0.01A | ACDC Firmware V4.16 | R1, R4 are 24k; C18, C20 bypassed; C104 C105 pulldowns present; ferrites present L8, L9, L11, L12 ; R44 burnt and getting replaced | |||||||||||||||||
38 | ACDC 45 | 12/6/2019 | ANITA Lab (Oberla) | 12/1/2019 | U. of C. test-beam | ACDC Rev C 2019 | Cyclone GX IV | ||||||||||||||||||||||
39 | ACDC 46 | 2/22/2024 | Cameron | Fermilab (FTBF) | 12/1/2019 | U. of C. test-beam | ACDC Rev C 2019 | Cyclone GX IV | Inductor L3 removed, jumper wire soldered | Working (2/22/24), however the JCPLL is not configured on startup despite trying to write to EEPROM | ACDC Firmware V4.15 | R1, R4 are 24k, C18 C 20 bypassed; no other mods | |||||||||||||||||
40 | ACDC 47 | 6/15/2023 | Ian | Fermilab (FTBF) | 12/1/2019 | U. of C. test-beam | ACDC Rev C 2019 | Cyclone GX IV | 3.8V switching regulator works, 1.8 does not | Pulldown resistors added to fix the switching regulators. Works(June 2023) | ACDC Firmware V4.05 | R4,R1 19.1k-ohm; R29, R30 20 mOhm; C18, C20 bypassed; pulldown resistors present; J6 connected, R10/11 removed | |||||||||||||||||
41 | ACDC 48 | 6/7/2023 | Ian | Fermilab (FTBF) | 6/5/2023 | U. of C. test-beam | ACDC Rev C 2019 | Cyclone GX IV | U15, the pll chip need replacement. Need to send to Best. DLL unlocks in 5 seconds. (UC) | D1 and L13 bypassed, R1, R4 24.3k, C18, C20 bypassed, pulldowns added, R29 and R30 20m-ohm, U15 replaced, Clock selector removed, R10/11 removed | |||||||||||||||||||
42 | ACDC unlabeled | 4/27/2022 | ACDC Rev B 2014 | On-board linear regulators | shipped from ISU | ||||||||||||||||||||||||
43 | ACDC 49 | 2/22/2024 | Cameron | U of C (ACC 123) | 8/6/2021 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching, jumper cable fix | J3, J4 | Working (2/22/24) | ACDC Firmware V4.15 | R1, R4 are 24k; C104, C105 pulldowns present; no other mods | ||||||||||||||||
44 | ACDC 50 | 5/8/2024 | Cameron | U of C (MCP 150) | 8/6/2021 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching, jumper cable fix | J3, J4 | Working (2/22/24) | ACDC Firmware V4.16 | R1, R4 are 24k; C104 C105 pulldowns present; J5 connected (J6 pad broken), XX_R10, XX_R11 removed | ||||||||||||||||
45 | ACDC 51 | 5/3/2024 | Cameron | U of C (MCP 150) | 6/5/2023 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching | J3, J4 | 3.8V switching regulator works, 1.8 does not | ACDC Firmware V4.05 | R1, R4 24 k-Ohm; R29, R30 20m-ohm; C18, C20 bypassed; Pull-down resistors present; J6 connected, R10/11 removed | ||||||||||||||||
46 | ACDC 52 | 1/12/2022 | Jinseo | Fermilab (FTBF) | 8/6/2021 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching | J3, J4 | 3.8V switching regulator works, 1.8 does not | ACDC Firmware V4.05 | R1, R4 24 k-Ohm; R29, R30 20m-ohm; C18, C20 bypassed; Pull-down resistors present; J6 connected | ||||||||||||||||
47 | ACDC 53 | 5/3/2024 | Cameron | U of C (MCP 150) | 6/5/2023 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching | J3, J4 | 3.8V switching regulator works, 1.8 does not | ACDC Firmware V4.05 | R1, R4 24 k-Ohm; R29, R30 20m-ohm; C18, C20 bypassed; Pull-down resistors present; J6 connected, R10/11 removed | ||||||||||||||||
48 | ACDC 54 | 2/22/2024 | Cameron | U of C (ACC 123) | 8/6/2021 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching | J3, J4 | 3.8V switching regulator works, 1.8 does not | Working (2/22/24) | ACDC Firmware V4.15 | R1, R4 24 k-Ohm; R29, R30 20m-ohm; C18, C20 bypassed; Pull-down resistors present; J6 connected | |||||||||||||||
49 | ACDC 55 | 5/3/2024 | Cameron | U of C (MCP 150) | 8/6/2021 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching | J3, J4 | 3.8V switching regulator works, 1.8 does not | ACDC Firmware V4.05 | R1 19.1k-Ohm; R4 24.3k-Ohm; R29, R30 20m-ohm; C18, C20 bypassed; Pull-down resistors present; J6 connected, Clock selector removed, R10/11 removed | ||||||||||||||||
50 | ACDC 56 | 1/12/2022 | Fermilab (FTBF) | 8/6/2021 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching | J3, J4 | 3.8V switching regulator works, 1.8 does not | ACDC Firmware V4.05 | R1, R4 24 k-Ohm; R29, R30 20m-ohm; C18, C20 bypassed; Pull-down resistors present; J6 connected | |||||||||||||||||
51 | ACDC 57 | 12/13/2023 | Cameron | Fermilab (FTBF) | 8/6/2021 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching | J3, J4 | Function normally. | ACDC Firmware V4.05 | D1, L13 bypassed; R1，R4 are now 19.6k; R29/30 are now 0.02ohm; R36(removed) and is now pulldown 50 ohm for c268/253, J6 not connected, R10/11 removed | ||||||||||||||||
52 | ACDC 58 | 5/3/2024 | Cameron | U of C (MCP 150) | 8/6/2021 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching | J3, J4 | 3.8V switching regulator works, 1.8 does not | There was an electro static shock to the board, and the voltages are wrong. Need debugging. | R1 19k, R4 24k; C104/C105 has pulldown 50ohm resistor to GND; C18/C20 bypassed; R29/30 are now 0.02ohm; R36(removed) and is now pulldown 50 ohm for c268/253; J6 not connected | ||||||||||||||||
53 | ACDC 59 | 8/23/2024 | Jinseo | U of C Squires Lab (GCIS) | 8/6/2021 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching | J3, J4 | 3.8V switching regulator works, 1.8 does not | ACDC Firmware V4.05 | R1, R4 24 k-Ohm; R29, R30 20m-ohm; C18, C20 bypassed; Pull-down resistors present; J6 connected | ||||||||||||||||
54 | ACDC 60 | 4/30/2024 | Cameron | U of C (MCP 150) | 6/5/2023 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching | J3, J4 | 3.8V switching regulator works, 1.8 does not | Used to Function normally. DLL Unlock within 5 seconds. (UC) | ACDC Firmware V4.16 | R1 is now 19.1k, R4 is still 24k; C104/105 has pulldown 50ohm resistor to GND; R29/30 are now 0.02ohm; R36(removed), R44 is now 0ohm while R157 is open. XX_R10 and XX_R11 are open for all five PSEC4 | |||||||||||||||
55 | ACDC 61 | 5/16/2023 | Jinseo | U of C (ACC 123) | 8/6/2021 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching | J3, J4 | 3.8V switching regulator works, 1.8 does not | ACDC Firmware V4.15 | R1, R4 24 k-Ohm; R29, R30 20m-ohm; C18, C20 bypassed; Pull-down resistors present; J6 connected | ||||||||||||||||
56 | ACDC 62 | 1/12/2022 | Fermilab (FTBF) | 8/6/2021 | U of C | ACDC Rev C 2021 | Cyclone IV GX | Switching | J3, J4 | 3.8V switching regulator works, 1.8 does not | ACDC Firmware V4.05 | R1, R4 24 k-Ohm; R29, R30 20m-ohm; C18, C20 bypassed; Pull-down resistors present; J6 connected | |||||||||||||||||
57 | ACDC 63 | 5/9/2024 | Cameron | U of C (MCP 150) | n/a | ACDC Firmware V4.16 | |||||||||||||||||||||||
58 | ACDC 64 | 5/9/2024 | Cameron | U of C (MCP 150) | n/a | ACDC Firmware V4.16 | |||||||||||||||||||||||
59 | ACDC 65 | 5/9/2024 | Cameron | U of C (MCP 150) | n/a | ||||||||||||||||||||||||
60 | ACDC 66 | 5/9/2024 | Cameron | U of C (MCP 150) | n/a | ACDC Firmware V4.16 | |||||||||||||||||||||||
61 | ACDC 67 | 5/9/2024 | Cameron | U of C (MCP 150) | n/a | ACDC Firmware V4.16 | |||||||||||||||||||||||
62 | ACDC 68 | 5/9/2024 | Cameron | U of C (MCP 150) | n/a | ACDC Firmware V4.16 | |||||||||||||||||||||||
63 | ACDC 69 | 5/9/2024 | Cameron | U of C (MCP 150) | n/a | ACDC Firmware V4.16 | |||||||||||||||||||||||
64 | ACDC 70 | 5/9/2024 | Cameron | U of C (MCP 150) | n/a | ACDC Firmware V4.16 | |||||||||||||||||||||||
65 | Unlabeled ACDC | 9/3/2021 | U. of C. | U of C | ACDC Rev B 2014 | Cyclone IV GX | On Board Linear Regulators | J2, J3, J4, J16, J17 | Chip 2 does not seem to be working, after limited trials. All other chips are operational | ACDC Firmware V3.04 |
1 | Board Name/ID | Date updated | Current location | Date stuffed | FPGA | Description of current working status | Current firmware installed | Shipping Hiistory | |
|---|---|---|---|---|---|---|---|---|---|
2 | PSEC Eval 8 | 8/18/20 | Incom | Cyclone III | Michael Popecki is prepping for shipping to U. of C. | ||||
3 | PSEC Eval 9 | 8/31/20 | Evan's apartment, Batavia | Cyclone III | Channels are working and tested 8/31/20 | PSEC4 eval firmware | Prep for shipping to LHCb, contact is Vincenzo Vagnoni at vincenzo.vagnoni@cern.ch | ||
4 | PSEC Eval 10 | 8/31/20 | Evan's apartment, Batavia | Cyclone III | Can't test with PSEC4 mezz because I don't have the right version of Quartus to compile PSEC4 eval firmware... | PSEC4a eval firmware | |||
5 | PSEC Eval 11 | 8/18/20 | Argonne | Cyclone III | |||||
6 | PSEC4a mezzanine | 8/18/20 | EDG computer room | ||||||
7 | PSEC4 mezzanine | 8/18 | Attached to PSEC Eval 11 | ||||||
8 | PSEC4 mezzanine | 8/18 | Attached to PSEC Eval 8 | ||||||
9 | PSEC4 mezzanine | 8/31 | Attached to PSEC Eval 9 | Channels are working and tested 8/31/20 | Prep for shipping to LHCb, contact is Vincenzo Vagnoni at vincenzo.vagnoni@cern.ch | ||||
10 | PSEC Eval+mezz 12 (eric) | 8/31/20 | uchicago/KU | Cyclone III |
1 | ACDC | Total Current | Vin | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
2 | 10 | 1.55 | 5.05 | 4.94 | 3.28 | 2.05 | 4.94 | 2.49 | 1.24 | 3.27 | 3.27 | 1.2 | 1.2 | 0 | 3.27 | 3.27 | 1.2 | 1.2 | 0 |
3 | 26 | 1.43 | 5.05 | 4.94 | 3.33 | 2.08 | 4.94 | 2.48 | 1.24 | 3.28 | 3.28 | 1.2 | 1.2 | 0 | 3.28 | 3.28 | 1.21 | 1.2 | 0 |
4 | 26 - sockets | 5.05 | 4.84 | 3.31 | 2.06 | 4.84 | 2.48 | 1.24 | 3.26 | 3.26 | 2.49 | 1.78 | 0 | 3.28 | 3.28 | 1.2 | 1.2 | 0 | |
5 | 27 | 1.7 | 5.13 | 5 | 3.28 | 2.05 | 5 | 2.52 | 1.26 | 3.23 | 3.23 | 1.19 | 1.19 | 0 | 3.23 | 3.23 | 1.19 | 1.19 | 0 |
6 | 28 | 1.79 | 5.23 | 5.09 | 3.32 | 2.07 | 5.1 | 2.4 | 1.25 | 3.25 | 3.25 | 1.2 | 1.2 | 0 | 3.25 | 3.25 | 1.2 | 1.2 | 0 |
7 | 29 | 1.77 | 5.23 | 5.09 | 3.32 | 2.07 | 5.09 | 2.5 | 1.26 | 3.26 | 3.26 | 1.2 | 1.2 | 0 | 3.29 | 3.29 | 1.19 | 1.2 | 0 |
8 | 30 | 1.77 | 5.23 | 5.09 | 3.32 | 2.07 | 5.1 | 2.5 | 1.25 | 3.25 | 3.25 | 1.21 | 1.21 | 0 | 3.25 | 3.25 | 1.2 | 1.2 | 0 |
9 | 26, 2nd time | 1.43 | 5.23 | 5.1 | 3.33 | 2.08 | 5.1 | 2.49 | 1.25 | 3.28 | 3.28 | 1.2 | 1.2 | 0 | 3.28 | 3.28 | 1.21 | 1.2 | 0 |
10 | 31 | 1.75 | 5.23 | 5.08 | 3.31 | 2.07 | 5.08 | 2.5 | 1.25 | 3.25 | 3.25 | 1.2 | 1.19 | 0 | 3.25 | 3.25 | 1.2 | 1.2 | 0 |
11 | 32 | 1.66 | 5.23 | 5.1 | 2.53 | 1.59 | 5.11 | 2.49 | 1.25 | 2.47 | 2.47 | 1.19 | 1.19 | 0 | 2.47 | 2.47 | 1.2 | 1.2 | 0 |
12 | 33 | 1.79 -> 1.82 | 5.23 | 5.1 | 3.3 | 2.05 | 5.1 | 2.49 | 1.25 | 3.23 | 3.23 | 1.19 | 1.19 | 0 | 3.23 | 3.23 | 1.2 | 1.2 | 0 |
13 | 34 | 1.79->1.83 | 5.23 | 5.1 | 3.31 | 2.07 | 5.1 | 2.48 | 1.25 | 3.24 | 3.24 | 1.19 | 1.19 | 0 | 3.24 | 3.24 | 1.2 | 1.2 | 0 |
14 | 32, 2nd time | 1.78 | 5.23 | 5.1 | 3.3 | 2.06 | 5.1 | 2.49 | 1.25 | 3.24 | 3.24 | 1.19 | 1.19 | 0 | 3.23 | 3.23 | 1.2 | 1.2 | 0 |
15 | 35 | 1.83 | 5.23 | 5.1 | 3.29 | 2.05 | 5.1 | 2.48 | 1.24 | 3.23 | 3.23 | 1.2 | 1.19 | 0 | 3.22 | 3.22 | 1.2 | 1.2 | 0 |
16 | 25 | 1.44 -> 0.89 | 5.23 | 5.11 | 3.31 | 2.06 | 5.13 | 2.49 | 1.25 | 3.26 | 3.26 | 2.47 | 1.77 | 0 | 3.27 | 3.27 | 1.19 | 1.19 | 0 |
17 | 36 | 1.75 | 5.23 | 5.1 | 3.29 | 2.04 | 5.1 | 2.47 | 1.24 | 3.22 | 3.22 | 1.19 | 1.19 | 0 | 3.22 | 3.22 | 1.2 | 1.2 | 0 |
18 | 25, 2nd time | 1.49->1.08 | 5.23 | 5 | 3.31 | 2.06 | 5 | 2.5 | 1.25 | 3.26 | 3.26 | 1.19 | 1.19 | 0 | 3.27 | 3.27 | 1.19 | 1.19 | 0 |
19 | 37 | 5.38 | 5.2 | 3.3 | 2.05 | 5.2 | 2.5 | 1.25 | 3.26 | 3.26 | 1.2 | 1.2 | 0 | 3.3 | 3.3 | 0.9 | 0.9 | 0 | |
20 | 41 | ||||||||||||||||||
21 | |||||||||||||||||||
22 | |||||||||||||||||||
23 | |||||||||||||||||||
24 | |||||||||||||||||||
25 | |||||||||||||||||||
26 | |||||||||||||||||||
27 | |||||||||||||||||||
28 | |||||||||||||||||||
29 | |||||||||||||||||||
30 | ACC | Total current with acc_125MHz_8b10b_withtrig.sof | |||||||||||||||||
31 | 1 | 2.58 | 5.51 | ||||||||||||||||
32 | 4 | 2.07 | 5.51 | ||||||||||||||||
33 | 12 | 2.1 | 5.51 | ||||||||||||||||
34 | 13 | 2.12 | 5.51 | ||||||||||||||||
35 | |||||||||||||||||||
36 | |||||||||||||||||||
37 | ACC | Rx.sof | acc_125MHz_8b10b_withtrig.sof | Rx.pof | acc_125MHz_8b10b_withtrig.pof | ||||||||||||||
38 | 10 | 3.02 | 2.16 | ||||||||||||||||
39 | 4 | 2.64 | 2.08 | ||||||||||||||||
40 | 1 | 3.46 | 2.47 |
1 | sheets | Date updated | Current location | Date stuffed | Ownership | Board type | FPGA | Oscillator | Description of current working status | Current firmware installed | Shipping History | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
2 | ACC alpha | 4/27/2022 | Test Beam | 6/2016 | U. of C. | Annie Central Card | Arria V | 125 MHz | 25MHz 8b10b, sma6 trigger | ||||||||||||||||
3 | ACC beta | 1/7/2020 | Test Beam | 6/2016 | U. of C. | Annie Central Card | Arria V | 125 MHz | 25MHz 8b10b, sma6 trigger | ||||||||||||||||
4 | ACC 1 | 7/25/2023 | Sciboone | 6/2017 | ANNIE | Annie Central Card | Arria V | 125 MHz | (12/06/2021) Flashed w/ DG's firmware version a301 but ACC is not recognized by "connectedBoards" prog | 125 MHz 8b10b, sma6 trigger | |||||||||||||||
5 | ACC 2 | 12/13/2023 | Test Beam | 6/2017 | ANNIE | Annie Central Card | Arria V | 125 MHz | (6/30/2021) Port 2 not working after ground path tests; only sees ACDC boards at port 4; B. Adams will try to fix buffers. (8/6/2021) Paul Rubinov replaced buffer chips and now all ports appear to be working. | D. Greenshields firmware v200 (5/27) | |||||||||||||||
6 | ACC 3 | 7/25/2023 | U. of C. MCP 106 | 6/2017 | Test Beam? | Annie Central Card | Arria V | 125 MHz | (7/28/2023)The FPGA is unresponsive. Cannot program it. | 125 MHz 8b10b sma 6 trigger | |||||||||||||||
7 | ACC 4 | 7/14/2020 | U. of C. ?? | 6/2017 | ANNIE | Annie Central Card | Arria V | 125 MHz | 125 MHz 8b10b, sma6 trigger | ||||||||||||||||
8 | ACC 5 | 1/3/2020 | Warwick with Greenshields | 6/2017 | ANNIE | Annie Central Card | Arria V | 125 MHz | Un-tested | None | shipped to Warwick | ||||||||||||||
9 | ACC 11 | 7/25/2023 | Test Beam? | 6/2017 | ANNIE | Annie Central Card | Arria V | 125 MHz | Unknown | Unknown | |||||||||||||||
10 | ACC 12 | 7/14/2020 | U. of C. ?? | 2/15/20 | U. of C. | Annie Central Card | Arria V | 125 MHz | 125 MHz 8b10b, sma6 trigger | ||||||||||||||||
11 | ACC 13 | 7/25/2023 | Sciboone | 7/14/20 | U. of C. | Annie Central Card | Arria V | 125 MHz | (6/30/2021) Port 2 not working after ground path tests. (8/6/2021) Paul Rubinov replaced buffer chips and now all ports appear to be working. | D. Greenshields firmware v301/304 (6/22) | |||||||||||||||
12 | ACC 14 | 5/9/2023 | Lab 6 | 5/9/2023 | U. of C. | Annie Central Card | Arria V | 125 MHz | |||||||||||||||||
13 | ACC 15 | 5/9/2023 | Lab 6 | 5/9/2023 | U. of C. | Annie Central Card | Arria V | 125 MHz | |||||||||||||||||
14 | ACC 16 | 5/9/2023 | Fermilab (FTBF) | 5/9/2023 | U. of C. | Annie Central Card | Arria V | 125 MHz | |||||||||||||||||
15 | ACC 17 | 7/29/2024 | UC Squires Lab | 5/9/2023 | U. of C. | Annie Central Card | Arria V | 125 MHz | Ask Kepler | ||||||||||||||||
16 | ACC 18 | 6/7/2023 | Fermilab (FTBF) | 5/9/2023 | U. of C. | Annie Central Card | Arria V | 125 MHz | |||||||||||||||||
17 | ACC 19 | 6/7/2023 | Fermilab (FTBF) | 5/9/2023 | U. of C. | Annie Central Card | Arria V | 125 MHz | |||||||||||||||||
18 | |||||||||||||||||||||||||
19 | |||||||||||||||||||||||||
20 | Central Card 1 | 7/14/2020 | U. of C. | 2014 | U. of C. | Central Card | 40 MHz | Unknown | |||||||||||||||||
21 | Central Card 2 | 7/14/2020 | U. of C. | 2014 | U. of C. | Central Card | 40 MHz | Unknown | |||||||||||||||||
22 | Central Card 3 | 7/14/2020 | U. of C. | 2014 | U. of C. | Central Card | 40 MHz | Unknown |
1 | Board type | Date updated | Last Edited By | Current location | Quantity | ||
|---|---|---|---|---|---|---|---|
2 | ACC | 1/26/2023 | Evan Angelico | U. of C. | 10 | ||
3 | ACDC rev C | 1/26/2023 | Evan Angelico | U. of C. | 30 | ||
4 | ACC "Fixit" board | U. of C. | ? | mezzanine to fix *?* chip availability |
1 | Change made | Board Name(s)/ID | Date | Experimenter | Location of change |
|---|---|---|---|---|---|
2 | Re-soldered one of the pins of a voltage regulator that had previously been lifted off | ACDC 4 | 10/24/18 | Evan | U. of C. |
3 | Removed R40 | ACDC 21 | 10/24/18 | Evan | U. of C. |
4 | Flashed 25->25MHz firmware | ACDC 22, 21, 20, 24 | 10/24/18 | Evan | U. of C. |
5 | Flashed 25->40MHz firmware from jic ACDC10 | ACDC 4, 2, 7 | 10/24/18 | Evan | U. of C. |
6 | Flashed 25->40MHz firmware from jic ACDC10 | ACDC 24, 21 | 11/14/2018 | Evan | U. of C. |
7 | Changed 25MHz oscillators to 40MHz oscillators | ACDC 20, 22 | 11/14/2018 | Evan | U. of C. |
8 | Flashed 25->40MHz firmware from jic ACDC10 | ACDC 20, 22 | 11/14/2018 | Evan | U. of C. |
9 | Replaced 40MHz oscillator with a new 40MHz oscillator | ACDC 20, 7, 22 | 11/15/2018 | Evan | U. of C. |
10 | Replaced capacitors C31/C32 on all PSEC4 chips with 0.1muF capacitors | ACDC 7, 10, 24, 20 | 11/15/2018 | Evan | U. of C. |
11 | Replaced all PSEC4 chips | ACDC 20 | 11/15/2018 | Evan | U. of C. |
12 | Replaced chips 2 and 3 (where 0 is farthest from cal-input SMA) | ACDC 20 | 11/19/2018 | Evan | U. of C. |
13 | Put one SMA jack on the cal input, J4 | ACDC34 | 2/28/2019 | Evan | U. of C. |
14 | Attached a wire with solder to the RJ45 case | ACDC 20, 10 | 4/5/2019 | Evan | FTBF |
15 | Reduced the size of the first stage LDO heat sink so that it does not pass the board boundaries | ACDC 20, 10 | 9/6/2019 | Evan | FTBF |
16 | Removed the calibration SMAs near the samtec connectors | ACDC 20, 10 | 9/6/2019 | Evan | FTBF |
17 | Removed calibration SMAs near samtec connectors | ACDC 37-42 | 9/12/2019 | Evan | U. of C. |
18 | I applied 30V to the inputs by accident, exploding at least two capacitors. Components were changed and the board now communicates properly | ACDC 20 | 9/12/2019 | Evan | U. of C. |
19 | I applied 30V to the inputs by accident, exploding at least two capacitors. Components were changed but still a power issue | ACDC 10 | 9/12/2019 | Evan | U. of C. |
20 | Attached a mini-bannana ground wire to ethernet chassis | ACDC 38 | 9/24/2019 | Evan | FTBF |
21 | Removed the incorrect sma jacks from calibration ports | ACDC 38 and 40 | 9/24/2019 | Evan | FTBF |
22 | On half of the boards in ACDC37-42 series, the last linear regulators were found to be LT3080's as opposed to the LT3083's from previous versions. All boards with LT3080 regulators need 120k setpoint resistors as opposed to the 24k from the other version. Mark replaced those resistors | ACDC 37 - 42 | 9/12/2019 | Evan | U. of C. |
23 | Replaced the setpoint resistor on the LT3083 regulator as it looked bad and I was getting low output voltage. This ended up not making a difference | ACDC 37 | 9/26/2019 | Evan | U. of C. |
24 | Replaced that regulator with new LT3080 with two resistors in parallel | ACDC 37 | 10/3/2019 | Evan | U. of C. |
25 | Removed inductors that connect switching and linear power block to the rest of board | ACDC 43-44 | 12/1/2019 | Evan | U. of C. |
26 | Replaced all of the components on the power block that are connected to U1 regulator. In this way, Mark Z. found a shorting small smd capacitor that was shorting the 5V plane to ground. This board now works | ACDC 10 | 2/18/20 | Evan | U. of C. |
27 | Replaced the 5 pin regulator U11 and some periferal components. This did not solve the problem that this board draws 2x more current than it should. | ACDC 39 | 2/18/20 | Evan | U. of C. |
28 | Removed L3 and soldered a jumper wire from 3.8 to 1.8V power planes from test points | ACDC 46 | 7/8/21 | Toby and Marek | U. of C. |
1 | Change made | Board Name(s)/ID | Date | Experimenter | Location of change |
|---|---|---|---|---|---|
2 | Epoxied down the USB jack | ACC alpha | 10/10/2018 | Evan | U. of C. |
3 | Attached two RJ45 case ground wires to the RJ45 case with solder | ACC beta | 4/5/2019 | Evan | FTBF |
4 | I put 40MHz oscillators in the positions where the 125MHz oscillators used to be | ACC 4 | 7/25/2019 | Evan | U. of C. |
5 | Replacing the 125MHz oscillators | ACC 4 | 10/11/2019 | Evan | U. of C. |
6 | BEST replaced the FPGAs | ACC 1 & 4 | 2/17/20 | Evan | U. of C. |
7 | New ACCs populated using U. of C. account | ACC 12 & 13 | 2/17/20 | Evan | U. of C. |
8 | Evan placed heat sinks on new fpgas | ACC 1 & 4 | 2/17/20 | Evan | U. of C. |
9 | New US12 and US13 capacitors | ACC 1, 12, & 13 | 2/18/20 | Evan | U. of C. |
10 | Cut the USB voltage regulator trace and soldered a wire between 3.3V test point to the LED 3.3V supply line | ACC 13 | 8/1/20 | Evan | Evan's House |
11 | Cut the USB voltage regulator trace and soldered a wire between 3.3V test point to the LED 3.3V supply line | ACC alpha | 8/14/20 | Evan | Lab 6 |
12 | Was exhibiting high and fluctuating current, and no USB connectivity, so we reprogrammed the board with acc_25M_withtrig sof | ACC alpha | 8/14/20 | Evan | Lab 6 |
1 | LAPPD # | Location | Owner | Notes | ||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
2 | 25 | Lab6 | ANNIE | Has Pick-Up Board | ||||||||||||||||||||||
3 | 31 | Lab6 | ANNIE | Low QE (4-5%), replaced with 63 but still keeping for full integration test | Has Pick-Up Board | |||||||||||||||||||||
4 | 37 | InCom | ANNIE | Came w/ HV problem. Was sent back to InCom and replaced with #58 | ||||||||||||||||||||||
5 | 39 | Lab6 | ANNIE | |||||||||||||||||||||||
6 | 40 | Lab6 | ANNIE | Has Pick-Up Board | ||||||||||||||||||||||
7 | 42 | FTBF | Fermilab | loaner, low QE ~14% | ||||||||||||||||||||||
8 | 43 | FTBF | Fermilab | |||||||||||||||||||||||
9 | 51 | FTBF | UC | inside out | inside out | |||||||||||||||||||||
10 | 58 | Lab6 | ANNIE | Replacement for #37 | Has Pick-Up Board | |||||||||||||||||||||
11 | 63 | Lab6 | ANNIE | Replacement for #31 | ||||||||||||||||||||||
12 | 64 | Lab6 | ANNIE | |||||||||||||||||||||||
13 | 66 | FTBF | Fermilab | |||||||||||||||||||||||
14 | 86 | Test Beam | Test Beam |
1 | LVHV ID/Name | LAPPD partner | status last updated | current location | description of current working status | beam gate | |||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
2 | LVHV #1 | 40 | 01/18/2022 | FNAL | modified power protection circuit UV/OV window | DC-coupled | |||||||||||||||||||||
3 | LVHV #2 | 40 | 01/18/2022 | FNAL | non-functional humidity sensor; bypassed power protection circuit | DC-coupled | |||||||||||||||||||||
4 | LVHV | 63 | 01/18/2022 | UC Davis | AC-coupled | ||||||||||||||||||||||
5 | LVHV | 58 | 01/18/2022 | UC Davis | AC-coupled | ||||||||||||||||||||||
6 | LVHV | 39 | 01/18/2022 | UC Davis | AC-coupled | ||||||||||||||||||||||
7 | LVHV | 64 | 01/18/2022 | UC Davis | AC-coupled | ||||||||||||||||||||||
8 | LVHV | 01/18/2022 | UC Davis | AC-coupled | |||||||||||||||||||||||
9 | LVHV | 01/18/2022 | UC Davis | AC-coupled | |||||||||||||||||||||||
10 | LVHV | 01/18/2022 | UC Davis | missing humidity sensor | AC-coupled | ||||||||||||||||||||||
11 | LVHV | 01/18/2022 | UC Davis | missing humidity sensor | AC-coupled | ||||||||||||||||||||||
12 | |||||||||||||||||||||||||||
13 | |||||||||||||||||||||||||||
14 | OLD LVHV (2019 design) | ||||||||||||||||||||||||||
15 | LVHV #1 | 1/18/2022 | Lab 6 | has most recent HV protection changes + SPI humidity sensor | |||||||||||||||||||||||
16 | LVHV #2 | 10/22/2021 | Lab 6 Conference room | damaged by power supply | |||||||||||||||||||||||
17 | LVHV #3 | 10/22/2021 | Lab 6 Conference room | used for LAPPD #31 load tests - no trigger board interface or HV protection | |||||||||||||||||||||||
18 | LVHV #4 | 6/13/2021 | UC Davis (e-shop) | unmodified | |||||||||||||||||||||||
19 | LVHV #5 | 7/21/2021 | Lab 6 | unmodified | |||||||||||||||||||||||
20 | LVHV #6 | 6/13/2021 | Lab 6 | has most recent HV protection changes + SPI humidity sensor; used for LAPPD #40 tests |
1 | breakout box ID/name | status last updated | current location | description of current working status | RPis inside | microSD? | ||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
2 | B.o.B. #1 | 6/22/2021 | Lab 6 | used for dark room tests | pi-bb1, pi-bb2 | yes, no | ||||||||||||||||||||
3 | B.o.B. #2 | 1/18/2022 | Lab 6 | used for rack fit tests at the hall | pi-bb3, pi-bb4 | no, yes | ||||||||||||||||||||
4 | B.o.B. #3 | 1/18/2022 | Lab 6 | not tested | pi-bb5, pi-bb6 | no, no |
1 | waterproof cable ID/name | status last updated | current location | length | description of current working status | wet side | dry side | ||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
2 | 1 | 1/18/2022 | Lab 6 high bay | 7 m | Used for dark room tests. [01/16/22] splice redone w/ blue MA connector; waterproofed and soaked. [01/18/22] fixed issues w/ spliced connections; tested in dark room; soaked. | blue MacArtney (M) | ethernet jack | ||||||||||||||||||||
3 | 2 | 1/18/2022 | Lab 6 high bay | 7 m | Used for dark room tests. [12/2021] splice redone with blue MacArtney connector. [01/17/22] fixed up issues w/ spliced connections; waterproofed and soaked. [01/19/22] redid splice w/ crimp connectors and splints; tested in dark room; waterproofed and soaked. | blue MacArtney (M) | ethernet jack | ||||||||||||||||||||
4 | 6/22/2021 | Lab 6 high bay | 10 m | used for deployment test; terminated with incompatible Amphenol connector | MacArtney (M) | Amphenol (M) | |||||||||||||||||||||
5 | 6/22/2021 | Lab 6 high bay | 10 m | used for deployment test; terminated with incompatible Amphenol connector | MacArtney (M) | Amphenol (M) | |||||||||||||||||||||
6 | 1/18/2022 | Lab 6 high bay | 10 m | not tested | MacArtney (M) | not terminated | |||||||||||||||||||||
7 | 1/18/2022 | Lab 6 high bay | 10 m | not tested | MacArtney (M) | not terminated | |||||||||||||||||||||
8 | 6/22/2021 | Lab 6 high bay | 10 m | not tested | MacArtney (M) | not terminated | |||||||||||||||||||||
9 | 6/22/2021 | Lab 6 high bay | 10 m | not tested | MacArtney (M) | not terminated | |||||||||||||||||||||
10 | 1/18/2022 | Lab 6 high bay | 10 m | not tested | MacArtney (M) | not terminated | |||||||||||||||||||||
11 | 1/18/2022 | Lab 6 high bay | 10 m | not tested | MacArtney (M) | not terminated | |||||||||||||||||||||
12 | |||||||||||||||||||||||||||
13 | |||||||||||||||||||||||||||
14 | |||||||||||||||||||||||||||
15 | (spare) connectors | ||||||||||||||||||||||||||
16 | number of Amphenol(F) connectors | 16 | 4 used, 3 to UK | ||||||||||||||||||||||||
17 | number of Amphenol(M) connectors | 12 | 2 used | ||||||||||||||||||||||||
18 | number of MacArtney(F) connectors | 14 | 4 used | ||||||||||||||||||||||||
19 | number of MacArtney(M) connectors (wet side) | 13 | 10 used |
1 | trigger board ID/name | LAPPD partner | status last updated | current location | description of current working status | ||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
2 | 40 | 8/9/2021 | Lab 6 dark room | complete board; I2C communications tested | |||||||||||||||||||||||
3 | 6/22/2021 | dark room | incomplete board; I2C communications tested |