Slice Temperature Sensors - RT Tables


1	300°C Thermistor
2	WARNING
3	Use of Slice Engineering's 300°C Thermistor requires firmware modification. Improperly configured firmware can cause a fire! Marlin and Duet3D® firmware support the Slice Engineering® 300°C Thermistor. In your firmware settings, choose the 100K thermistor - ATC Semitec 104NT-4-R025H42G. Refer to documentation at marlinfw.org or configurator.reprapfirmware.org to configure your firmware PRIOR TO USE. DO NOT defeat the thermal runaway protection in your firmware. This will void any and all warranties. If your printer uses an older version of open source firmware, use the Resistance-Temperature Table below.
4	R25 (kΩ)	100 ± 3%
5	β25/85 (K)	4267 ± 2%
6	Resistance (Ω)	Temperature (℃)

7	1136000	-20
8	623200	-10
9	354600	0
10	208800	10
11	126900	20
12	100000	25
13	79330	30
14	50900	40
15	33450	50
16	22480	60
17	15430	70
18	10800	80
19	9094	85
20	7690	90
21	5569	100
22	4097	110
23	3058	120
24	2313	130
25	1770	140
26	1371	150
27	1074	160
28	850.1	170
29	679.3	180
30	547.6	190
31	445.2	200
32	365	210
33	301.6	220
34	251	230
35	210.4	240
36	177.5	250
37	150.7	260
38	128.7	270
39	110.5	280
40	95.39	290
41	82.78	300


1	450°C Thermistor
2	WARNING
3	Use of Slice Engineering's 450°C High Temperature Thermistor requires firmware modification. Improperly configured firmware can cause a fire! Marlin 2.0 and Duet3D® firmware support the Slice Engineering High Temperature thermistor. Refer to documentation at marlinfw.org or configurator.reprapfirmware.org to configure your firmware PRIOR TO USE. DO NOT defeat the thermal runaway protection in your firmware. This will void any and all warranties. If your printer uses an older version of open source firmware, use the Resistance-Temperature Table below.
4	R25 (kΩ)	500 ± 3%
5	β25/85 (K)	3800 ± 2%
6	Resistance (Ω)	Temperature (℃)

7	4018000	-20
8	2407000	-10
9	1497000	0
10	943200	10
11	613400	20
12	500000	25
13	407000	30
14	275000	40
15	190300	50
16	132900	60
17	94760	70
18	68870	80
19	59110	85
20	50750	90
21	37870	100
22	28590	110
23	21890	120
24	16920	130
25	13240	140
26	10480	150
27	8365	160
28	6745	170
29	5490	180
30	4509	190
31	3734	200
32	3104	210
33	2600	220
34	2193	230
35	1862	240
36	1591	250
37	1359	260
38	1168	270
39	1009	280
40	876	290
41	764.4	300
42	668.9	310
43	587.9	320
44	519	330
45	460	340
46	409.3	350
47	365.4	360
48	327.3	370
49	294.2	380
50	265.3	390
51	240	400
52	217.7	410
53	198	420
54	180.5	430
55	165.1	440
56	151.3	450
57	138.9	460
58	127.9	470
59	118	480
60	109.1	490
61	101.1	500


1	RTD Pt1000
2	WARNING
3	Use of Slice Engineering's RTD Pt1000 requires firmware modification. Improperly configured firmware can cause a fire! Marlin and Duet3D® firmware support the Slice Engineering RTD Pt1000. Refer to documentation at marlinfw.org or configurator.reprapfirmware.org to configure your firmware PRIOR TO USE. DO NOT defeat the thermal runaway protection in your firmware. This will void any and all warranties. Check with your 3D printer manufacturer to see if an amplifier circuit is needed for an RTD Pt1000.
4	R0 (Ω)	1000
5	α (1/℃)	0.00385 ± 0.1%
6	Resistance (Ω)	Temperature (℃)

7	921.6	-20
8	960.9	-10
9	1000	0
10	1039	10
11	1077.9	20
12	1097.3	25
13	1116.7	30
14	1155.4	40
15	1194	50
16	1232.4	60
17	1270.8	70
18	1309	80
19	1328.1	85
20	1347.1	90
21	1385.1	100
22	1422.9	110
23	1460.7	120
24	1498.3	130
25	1535.8	140
26	1573.3	150
27	1610.5	160
28	1647.7	170
29	1684.8	180
30	1721.7	190
31	1758.6	200
32	1795.3	210
33	1831.9	220
34	1868.4	230
35	1904.7	240
36	1941	250
37	1977.1	260
38	2013.1	270
39	2049	280
40	2084.8	290
41	2120.5	300
42	2156.1	310
43	2191.5	320
44	2226.8	330
45	2262.1	340
46	2297.2	350
47	2332.1	360
48	2367	370
49	2401.8	380
50	2436.4	390
51	2470.9	400
52	2505.3	410
53	2539.6	420
54	2573.8	430
55	2607.8	440
56	2641.8	450
57	2675.6	460
58	2709.3	470
59	2742.9	480
60	2776.4	490
61	2809.8	500

Published by Google Sheets–Report Abuse–Updated automatically every 5 minutes