| A | B | C | D | E | F | G | H | I | J | |
|---|---|---|---|---|---|---|---|---|---|---|
1 | 2 | Motor Piece | 2 | 5V power supply - also one for Arduino | 1 | Atmega328p-pu / bootloader | ||||
2 | 5 | Carriage Piece | 6"x6" | spring steel | 1 | 28 Pin DIL Socket | ||||
3 | 5 | Idler Piece | 1 | bed plate, 6"x6" | 1 | 16MHz crystal | ||||
4 | 1 | Z to X axis Connector | 6"x6" | Buildtak surface | 1 | stripboard | ||||
5 | 2 | Z axis Base | 4 feet | split wire loom | 2 | 100uF 25V electrolytic capacitors | ||||
6 | 1 | Y Axis Raised Idler | 25 | zip ties for wire management | 2 | 100uF 50V ceramic disk capacitors | ||||
7 | 1 | Y Axis Raised Motor Piece | 0.5 | heat shrink | 2 | 22pF ceramic disc capacitors | ||||
8 | 1 | main extruder piece | 1 | solder | 1 | tactile switch | ||||
9 | 1 | secondary extruder piece | 15 | ferrules | 2 | LED - one for power electronics | ||||
10 | 1 | extruder idler piece | 1 | wood base, 11.25"x12.5" | 1 | 220ohm resistor | ||||
11 | 1 | Control Panel | 7 | skate bearings | 1 | jumper wire for breadboard | ||||
12 | 1 | Spool Holder | 1 | 0.5"x1"x2" 6061 aluminum for heat sink | 1 | jumper wire spools | ||||
13 | 6 | Belt Pegs | 1 | spring for extruder | 1 | 6 pin female header right-angle | ||||
14 | 2 | Wire Loom Clip | 1 | mk7 drive gear | 1 | 40 pin female headers | ||||
15 | 2 | Endstops | 2 | m3x30 cap head screw, heat sink | 1 | Serial to USB converter | ||||
16 | 2 | m6x30 for attaching extruder | 1 | m3x18 cap head screw, idler | 1 | arduino uno | ||||
17 | 1 | m6x25 for tool attach | 3 | m3x8 cap head screw, main + side attach | 2 | copper clad boards | ||||
18 | 35 | m6x18 zinc plated socket screw | 1 | height sensor- 5V PNP - LJ18A3-8-Z/BY-5V | 1 | muriatic acid + hydrogen peroxide | ||||
19 | 36 | m6 zinc plated nut | 2 | 2.9x13mm self tapping screws for fan | 1 | 555 motor | ||||
20 | 12 | m3x25 SS socket head screw | 1 | 24V 4040 fan | 1 | motor coupler for 1/8" mill bit | ||||
21 | 6 | 8 mm rods | 1 | 24V 5015 blower | 2 | 1 mm mill bit | ||||
22 | 19 | 1-1/4" screws | 2 | fan heat sink | 1 | hacksaw blade | ||||
23 | 4 | nema 17, 72 oz in stepper motors | 1 | heater block | 1 | box cutter blade | ||||
24 | 12 | 8 mm linear bearing | set | 0.4, 0.8, and 1.2 mm nozzle set | 1 | safety glasses - for spindle | ||||
25 | 7 feet | GT2 belt, 6mm wide | 1 | heater sock | Soldering iron | |||||
26 | 3 | GT2 pulley, 5mm bore, 6mm wide, 20 teeth | 1 | heat break | 1 | screen - includes HDMI cable | ||||
27 | 6 | m6x12x4 flanged bearing | 1 | thin m6 nut | 1 | pi 4B 4GB RAM | ||||
28 | 12 | 3x12mm N52 magnets | 1 | thermistor | 1 | pi cooling fan | ||||
29 | 3 feet | 22 ga wire | 1 | 40W 24V heater | 1 | pi power cable - for wall power + charging | ||||
30 | 2 | end stops + wires | 1 | 5 mm hex key - main tool | 1 | battery pack | ||||
31 | 4 | stepper motor wires | 1 | 2 mm hex key | 1 | pi 2 camera module | ||||
32 | 1 | GFCI outlet | 1 | 2.5 mm hex hey | 1 | usb c cable for power supply | ||||
33 | 1 | 12/24V power supply | 1 | small philips head screwdriver | ||||||
34 | 1 | plug | 1 | small flathead screwdriver | ||||||
35 | 1 | power cord | 1 | philips driver bit | ||||||
36 | 1 | RAMPS + MEGA + drivers + LCD | 1 | crazy glue | ||||||
37 | 2 | USB A to B cords (printer + Arduino) | 1 | black contact paper | ||||||
38 | 1 | SD card, 8 GB | 1 | 1 spool filament |