SLA-printer Resin Precision-Fit Test-Gauge
 Share
The version of the browser you are using is no longer supported. Please upgrade to a supported browser.Dismiss

View only
 
 
ABCDEFGHIJKLMNOPQRSTUVWXYZAAABAC
1
SLA-printer Resin Precision-Fit Test-Gauge.
NOTE: If your software has some sort of "horizontal size compensation," please disable it or set it to 0.0.
Shake resin before printing then let air bubbles settle.
2
Hosted by Photonsters
https://github.com/Photonsters
Note: Print flat on the bed with no support.
3
4
Print this model:
https://www.thingiverse.com/thing:3325364
5
Video:
https://www.youtube.com/watch?v=tc8-v3YDM2c
6
Use this form to submit your test results:
https://docs.google.com/forms/d/1VVIo4WLNRmNHhQEd6YYyfDdULA1OKF2qzdLtWosaM2c
7
8
9
Printer ModelResin NameResin ColorGauge Passed
Cost per liter USD
Layer Thickness
Exposure Time
Room Remp (C)
Reported ByComments
10
11
Anycubic PhotonMonocure Rapid with 20% Flex100Clear+0.1090501228Robert Silvers
Seems like 15% blend is perfect for achieving nominal size.
12
EPAX X1Siraya EasyAmber-0.10$39501024Robert Silvers
Dead on precise. Amerilabs Town Space Needle not formed yet, so 11 seconds is probably ideal for this machine. 4 baselayers of 100 seconds made torsion socket break free so do more layers.
13
Anycubic PhotonAnycubic Clear-0.1052501120Ryan
Exposure time could be adjusted down further as writing was a +/- signs were a bit difficult to see. Not to much of a smell and doesn't come out yellow.
14
Anycubic PhotonBoRapPurple clear-0.10501228Robert Silvers
Good exposure if precision fit is needed.
15
Anycubic PhotonElegoo ClearClear-0.1053501028Robert Silvers
More brown cast than Monoprice clear.
16
Anycubic PhotonElegoo Green
Green - maybe transparent?
-0.1044501020Sky Captain Hana
17
Anycubic PhotonElegoo RedTranslucent Red-0.1044501028Robert Silvers
18
Anycubic PhotoneSun BioResinRed-0.106050825Robert Silvers
Recommended exposure for precision fits.
19
Zortrax InkspireMonoprice RapidBlack-0.105350823James DeGroat
All Go Gauges fit like they should. I think I needed the exposure time a little longer for this resin. Will test again at a longer exposure. Pigment settled at bottom even after shaking.
20
Anycubic PhotonSiraya Blu + 10% Anycubic BlackDark Green-0.1055501230Robert Silvers
Lost some strength.
21
Anycubic PhotonSiraya Blu Tough Engineering ResinTransparent Blue-0.1055501025Robert Silvers
Dead-on precise at this exposure and temp.
22
Anycubic PhotonSiraya Blu Tough Engineering ResinTransparent Blue-0.1055501230Robert Silvers
Dead-on precise at this exposure and temp.
23
Anycubic Photon
Siraya Blu with 1 drop alcohol ink per 250 ml (0.02ml per 100g)
Transparent Blue-0.1055501228Robert Silvers
24
Anycubic Photon
Siraya Blu with 10% by weight 1/32 glass fiber added
Transparent Blue-0.1055501230Robert Silvers
Fibers sank to bottom. Not recommended unless you pause and stir a lot.
25
Form 1+HARZ Model ResinClear-0.10?100N/A20Robert Silvers
26
Zortrax InkspireZortrax ProBlack-0.10170501223James DeGroat
No post cure needed according to them, but later found out it was very weak. Very low smell, parts feel good, and fit the ring gauge exactly like they should.
27
Anycubic Photon SElegoo White-0.1040507.520Ardell
28
Zortrax InkspireElegoo ClearClear-0.155350822James DeGroat
Has a slight brownish tint to it after post curing. -0.10 goes about a 1/4 of the way in.
29
Anycubic PhotonElegoo WhiteWhite-0.1548501417Sky Captain HanaKinda smelly.
30
Anycubic PhotonMonoprice RapidClear-0.1553501228Robert Silvers
Warm tone color (yellowish). Significant vapors.
31
Anycubic PhotonElegoo GreyGray-0.2065501024Tobias Becher
Seven to eight seconds seemed to give the same results.
32
Anycubic PhotonBoRapPurple clear-0.20501528Robert Silvers
Good exposure to sharpen fine details.
33
Anycubic PhotonDragon ResinGray-0.2075501215Cagri Aydogan
Prints fine works great
34
Anycubic PhotonElegooBlue-0.20501428Robert SilversLight blue.
35
Zortrax InkspireElegooBlack-0.204850823James DeGroat
Very low smell, looks amazing with a matte finish. When scratched, it has a white powdered looked. The -1.5mm gauge goes half way and is more of a press fit. It can pass all the way with a lot of force.
36
Anycubic PhotoneSunGray-0.2060501222Ender Birer
GO -0.15mm also passed through but there was a little friction.
37
Anycubic PhotoneSun BioResinRed-0.2060501025Robert Silvers
This is the most exposure time it should have. I am trying less. No smell and stuck to plate unusually well.
38
Anycubic PhotoneSun General PurposeBlack-0.2060501025Robert Silvers
Space Needle in tact on Amerilabs Town, so 8 or 9 seconds would also work, and perhaps give a -0.1mm fit.
39
Anycubic PhotonMonocure RapidClear-0.2090501228Robert Silvers
Ideal for mineatures. Didn't notice any smell. Had four rows of needles on Amerilabs Town, so lots of detail.
40
Anycubic PhotonMonocure Rapid with 10% Flex100Clear-0.2090501228Robert Silvers
Ideal for mineatures. Didn't notice any smell. Had four rows of needles on Amerilabs Town, so lots of detail.
41
Anycubic PhotonMonoprice RapidGray-0.2053501428Robert Silvers
Many failed prints. Didn't stick to plate well even with 100 second layers.
42
Zortrax InkspireNOVA3d Standard Rigid ResinGray-0.207050822James DeGroat
Feels about the same as AC Grey resin and has similar smell. Part number for this resin is SRGR0-M00-1841. Overall this resin seems good
43
Anycubic PhotonSiraya Blu Tough Engineering ResinTransparent Blue-0.20551001230Robert Silvers
Layers too thinn. Not recommended at this setting.
44
Anycubic PhotonSiraya Blu Tough Engineering ResinTransparent Blue-0.2055501230Robert Silvers
Underexposed a bit. 50u was better dimensionally.
45
Anycubic PhotonSiraya Labs SculptDark Gray-0.2050501625Robert Silvers
Lost Space Needle on Amerilabs Town
46
Anycubic PhotonSiraya Labs SculptDark Gray-0.2050501825Robert Silvers
Had Space Needle on Amerilabs Town
47
Zortrax InkspireAnycubic Green/Transparent-0.3052501123Obe Bradford
48
Anycubic PhotonAnycubic Gray-0.305250822James DeGroat
Very low smell while printing, looks great for models, and feels fairly durable.
49
Anycubic PhotonAnycubic Gray-0.3052509.620Dustin Scott
Hardly any smell while printing, results may vary. Great for minis however, probably not the best for models where precision, or small detail is a key.
50
Anycubic PhotonAnycubic Gray-0.3052501422Robert Silvers
Not much smell.
51
Anycubic PhotonHARZ Model ResinBlack-0.3050820Robert Silvers
At 8 seconds, one of the parts disintigrated, indicating that exposure was too low. Also, no Space Needle on Amerilabs Town.
52
Anycubic PhotonAnycubic White-0.3+40-601001024Robert Silvers
Even the -0.3 gauge didn't really go. But less exposure is probably too little.
53
Anycubic PhotonHARZ Model ResinBlack-0.3+501020Robert Silvers
-0.3 gauge didn't go. Ok for it's purpose making models or shorten exposure. Amerilabs Town had the Space Needle.
54
55
Also see my torsion-strength tests: https://docs.google.com/spreadsheets/d/1JlqLSi4sxZLdA-hHCp6Ow4isoGMNI7nlE9Nmbj1ajWk/
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
By Robert Silvers: rsilvers129@gmail.com
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Loading...