A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | ||||||||||||||||||||||||||
2 | ||||||||||||||||||||||||||
3 | ||||||||||||||||||||||||||
4 | ||||||||||||||||||||||||||
5 | User Guide for Sculpt (For Sculpt only, not for Sculpt Ultra) | |||||||||||||||||||||||||
6 | For Sculpt - Ultra resin user guide, click here: | |||||||||||||||||||||||||
7 | For other resin user guides, please visit https://siraya.tech support section | |||||||||||||||||||||||||
8 | Sculpt is developed to be as the go-to resin for model makers with high hardness, great surface finish, excellent resolution and high temperature resistance at 160C | |||||||||||||||||||||||||
9 | Not only prints made with Sculpt is easy to get great looks with minimal post-processing effort. The hitemp feature allows Sculpt be used to make vulcanized rubber molds or to be printed as mold. | |||||||||||||||||||||||||
10 | ||||||||||||||||||||||||||
11 | Due to higher polymer content for its outstanding mechanical properties, the ideal printing condition for Sculpt is over 25C. | |||||||||||||||||||||||||
12 | If user can maintain a resin temperature of 30C, the printing time could be further reduced | |||||||||||||||||||||||||
13 | It is recommended to shake Sculpt bottle vigorously before pouring | |||||||||||||||||||||||||
14 | ||||||||||||||||||||||||||
15 | * Important, before printing Sculpt | |||||||||||||||||||||||||
16 | Sculpt has that dark grey colors that model makers love, and we have already seen some great prints. However, it is also the only Siraya Tech resin that has pigments, and it may settle. To get the best results out of Sculpt, SHAKE HARD (applies to all resins with pigments) To do it correctly to shake that bottle for 20-30s before use. Stir up the resins that is already in the vat before each print. And if you just received Sculpt, before opening it up for the first time, turn it upside down for a minute (submerged in warm water is even better) and then shake for another minute or two to make sure you get a great mix. IF you want to take it to next level, throw a small metal ball in there and shake, the object will significantly increase the efficiency of mixing pigments and resins. | |||||||||||||||||||||||||
17 | ||||||||||||||||||||||||||
18 | ||||||||||||||||||||||||||
19 | Exposure: Sculpt Grey | |||||||||||||||||||||||||
20 | Recommended | Resin Temperture 25-35C | Room temperature 20-28C | |||||||||||||||||||||||
21 | Printer | Layer Height | Exposure (s) | # of Initial Layers | Exposure for Init Layers | Exposure (s) | # of Initial Layers | Exposure for Init Layers | Note | |||||||||||||||||
22 | Photon | 50um | 18 (s) | 4 | 80 S | 18 (s) | 6 | 90 s | ||||||||||||||||||
23 | Shuffle | 50um | Use TR250 profile | https://www.dropbox.com/s/v7puaea58scxewr/profile_phrozen-tr250-50um-shuffle_2018-12-06.json?dl=1 | ||||||||||||||||||||||
24 | Shuffle XL | 50um | Use TR250 profile | https://www.dropbox.com/s/xinbughp5clviq7/profile_phrozen-tr250-50um-shuffle-xl_2018-12-06.json?dl=1 | ||||||||||||||||||||||
25 | EPAX X1 | 50um | 14 (s) | 4 | 60 s | 14 (s) | 6 | 75 s | ||||||||||||||||||
26 | Elegoo Mars | 50um | 14 (s) | 4 | 60 s | 14 (s) | 6 | 75 s | ||||||||||||||||||
27 | D7 | 50um | 15 (s) | 5 | 90 s | |||||||||||||||||||||
28 | Inkspire | 50um | 18 (s) | 6 | 90 s | Inkspire does not specify its light output, one user told us it is very closely to Photon | ||||||||||||||||||||
29 | Moonray | Moonray Ortho Clear Resin setting works well. | ||||||||||||||||||||||||
30 | Slash | 50um | 100um 5 sec 75um 4 sec 50um 3.5 sec 25um 2.8 sec 10um 2.5 sec - LED power 250 (default) - First layer for all 12sec/ first 3 layers (default amount). - Slow setting for Lift speed - 8mm lift height is safest and allow time resin to flow back (they only allow you to pick from 3,8, and 15mm height...which sucks...I'd like 6mm if I could. - Cooldown between layers on auto (smaller prints i do 2sec to speed things up) - Supports point(head) size no less than 1mm, but 1.5 is recommended with 2mm shaft. | |||||||||||||||||||||||
31 | ||||||||||||||||||||||||||
32 | ||||||||||||||||||||||||||
33 | Exposure: Sculpt Clear | |||||||||||||||||||||||||
34 | Recommended | Resin Temperture 25-35C | Room temperature 20-25C | |||||||||||||||||||||||
35 | Printer | Layer Height | Exposure (s) | # of Initial Layers | Exposure for Init Layers | Exposure (s) | # of Initial Layers | Exposure for Init Layers | Note | |||||||||||||||||
36 | Photon | 50um | 11(s) | 6 | 60 s | |||||||||||||||||||||
37 | Peopoly Phenom | 50um | 12s | 6 | 60 s | Use Peopoly Deft Profile to start | ||||||||||||||||||||
38 | EPA X1 | 50um | 8 (s) | 6 | 50 s | |||||||||||||||||||||
39 | Shuffle | 50um | 7.5(s) | 5 | 60 s | |||||||||||||||||||||
40 | Shuffle XL | 50um | 11(s) | 5 | 75 s | |||||||||||||||||||||
41 | Phrozen Transform | 50um | 8(s) | 5 | 60 s | due to variation in light system in Transform, best to calibrate your resin for your machine in your environment using this https://www.thingiverse.com/thing:4280278 | ||||||||||||||||||||
42 | ||||||||||||||||||||||||||
43 | ||||||||||||||||||||||||||
44 | Before Printing | |||||||||||||||||||||||||
45 | It is a good practice to mix resin and expose the bottom of the vat to air before printing. This replenish oxygen in the vat and helps reduce peel force. | |||||||||||||||||||||||||
46 | Sculpt especially benefit from mixing because it has pigments and may settle over time | |||||||||||||||||||||||||
47 | It would also ensure print consistency if user can get the initial resin temperature above 25 and keep the environmental temperature above 20 C | |||||||||||||||||||||||||
48 | ||||||||||||||||||||||||||
49 | Cleaning: | |||||||||||||||||||||||||
50 | Use a painter brush (or any brush made with hair) remove excess resins on the printed part with Use 95% concentrated Ethanol or IPA to clean. | |||||||||||||||||||||||||
51 | Do not submerge the parts in alcohol for more than 30 seconds. After 2-3 minutes of cleaning action, remove alcohol with a hair dryer or air blower. For complex part with lots cavities, it may be a good idea to clean/dry multiple times. | |||||||||||||||||||||||||
52 | User can check by touching the dryed surface of the part to see if it is still sticky. If the dryed surface is still sticky, wash some more and dry again. | |||||||||||||||||||||||||
53 | ||||||||||||||||||||||||||
54 | Sanding is easy with Sculpt. Use 1000 grit sand paper with a bit of mineral oil or water. Mineral oil adds lusters | |||||||||||||||||||||||||
55 | ||||||||||||||||||||||||||
56 | Post Curing: | |||||||||||||||||||||||||
57 | Sculpt reached its optimal strength when the printed part is post-cured with UV after cleaned. Use 395-405nm UV light and cure for about 15 minutes. | |||||||||||||||||||||||||
58 | Make sure resin is completely cleaned off and there is not alcohol left (it needs to be dry) on the print before curing. | |||||||||||||||||||||||||
59 | Curing by submerging object in water will significantly increase curing efficiency | |||||||||||||||||||||||||
60 | ||||||||||||||||||||||||||
61 | Mechanical Properties | |||||||||||||||||||||||||
62 | Heat Deflection Point: 160C | |||||||||||||||||||||||||
63 | Liquid Denisty (g/cm3) 1.13 | |||||||||||||||||||||||||
64 | Hardness (Shore D) 82 | |||||||||||||||||||||||||
65 | Tensile Strength at Break (Mpa) 63 | |||||||||||||||||||||||||
66 | Elogation at Break (%) 6 | |||||||||||||||||||||||||
67 | Young’s Modulus (MPa) 1000 | |||||||||||||||||||||||||
68 | Viscocity (cps at 25c) 400-700 | |||||||||||||||||||||||||
69 | ||||||||||||||||||||||||||
70 | ||||||||||||||||||||||||||
71 | MSDS | https://drive.google.com/open?id=1LLgV7orTDDU5vOMhUIQkvX2dLjG8wAJu | ||||||||||||||||||||||||
72 | ||||||||||||||||||||||||||
73 | ||||||||||||||||||||||||||
74 | ||||||||||||||||||||||||||
75 | ||||||||||||||||||||||||||
76 | ||||||||||||||||||||||||||
77 | ||||||||||||||||||||||||||
78 | ||||||||||||||||||||||||||
79 | ||||||||||||||||||||||||||
80 | ||||||||||||||||||||||||||
81 | ||||||||||||||||||||||||||
82 | ||||||||||||||||||||||||||
83 | ||||||||||||||||||||||||||
84 | ||||||||||||||||||||||||||
85 | ||||||||||||||||||||||||||
86 | ||||||||||||||||||||||||||
87 | ||||||||||||||||||||||||||
88 | ||||||||||||||||||||||||||
89 | ||||||||||||||||||||||||||
90 | ||||||||||||||||||||||||||
91 | ||||||||||||||||||||||||||
92 | ||||||||||||||||||||||||||
93 | ||||||||||||||||||||||||||
94 | ||||||||||||||||||||||||||
95 | ||||||||||||||||||||||||||
96 | ||||||||||||||||||||||||||
97 | ||||||||||||||||||||||||||
98 | ||||||||||||||||||||||||||
99 | ||||||||||||||||||||||||||
100 |