Fast by Siraya Tech - user guide
 Share
The version of the browser you are using is no longer supported. Please upgrade to a supported browser.Dismiss

View only
 
 
ABCDEFGHIJKLMNOPQRSTUVWXYZ
1
2
Shake the bottle and mix the resin in the vat before start printing!
3
4
5
User Guide for Fast
For other resin user guides, please visit https://siraya.tech support section
6
7
Fast is an affordable fast curing and non-brittle general application resin ideal for model making like tabletop minis, and figurines.
8
It is not a tough or engineering resin but can be mixed with Blu/Tenacious for more impact resistant.
9
10
While the ideal printing condition for Fast is over 20C, we have printed as long as 15C as long as the bottom layers uses more exposure time
11
12
Best print with recommended support setting, see below
13
14
Exposure (Same for Grey, White, Green)
15
Recommended
Resin Temperture 25-35C
Room temperature 20-25C
16
PrinterLayer HeightExposure (s)
# of Initial Layers
Exposure for Init LayersExposure (s)
# of Initial Layers
Exposure for Init Layers
Note
17
Photon50um10 (s)460 s11(s)660 s
18
Peopoly Phenom
50um12s660 s12s660 s
see below for detail settings
19
EPA X150um7.5 (s)445 s8 (s)650 s
20
EPA X1100um12 (s)475 s12 (s)690 s
21
Shuffle50um7.5(s)560 s
22
Shuffle XL50um11(s)575 s
23
Phrozen Transform
50um8(s)560 s
*see additional info below
24
D750um8(s)560 s
25
Inkspire50um11 (s)675 s
Inkspire does not specify its light output, one user told us it is very closely to Photon
26
Photon S50um8s560s8s560s
27
Mars50um8 (s)450 s8 (s)450 s
28
29
Before Printing
30
It is a good practice to stir resin in the vatand expose the bottom of the vat to air before printing. This replenish oxygen in the vat and helps reduce peel force.
31
32
Recommend best support settings:
33
34
We recommend medium preset support setting in chitubox for smaller prints. Heavy support for large prints on large priners
35
If you don't use chitubox, at least download a copy and see the detail settings for each preset and copy them over to your software of choice
36
37
Cleaning:
38
Use a painter brush (or any brush made with hair) remove excess resins on the printed part with Use 95% concentrated Ethanol (preferred) or IPA to clean. Some form of methnol should work but make sure it does not contain acetone.
39
Do not submerge the parts in alcohol for more than 30 seconds. After 2-3 minutes of cleaning action, remove alcohol with a hair dryer or air blower. For complex part with lots cavities, it may be a good idea to clean/dry multiple times.
40
User can check by touching the dryed surface of the part to see if it is still sticky. If the dryed surface is still sticky, wash some more and dry again.
41
42
Post Curing:
43
Fast reached its optimal strength when the printed part is post-cured with UV after cleaned. Use 395-405nm UV light and cure for about 5-10 minutes.
44
Make sure resin is completely cleaned off and there is not alcohol left (it needs to be dry) on the print before curing.
45
Curing by submerging object in water will significantly increase curing efficiency. Do not leave Fast prints in water for extended period of time (6hr). It may become very soft and need to be dried before using
46
47
Mechanical Properties
48
​Shore D 72
49
Tensile Strength 33Mpa
50
Young’s Modulus 800Mpa
51
Elongation At Break: 6%
52
Viscosity:100cps
53
Heat Deflection Temperature: 68C
54
MSDS
55
https://drive.google.com/open?id=1lWqnHnGQKKKlNFQRnKpSpGX_4cuvIxrP
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Loading...