ABCDEFGHIJKLMNOPQRSTUVWXYZ
1
11 Jun 2022fits...year dash series, or year..year. 63-01 is 1963 American, 63-10 is classic with 232. Roadster is a 61-01, modified. 68-01 is Esmond, 60-01 is Rambler American 2-door wagon.
2
Air intake duct hose63-01NAPA BK825-6038, 3-1/8" x 32"
3
AlternatorroadsterMitsubishi A1T25077. 35A, same as Dixie A-8829. in "T"-shaped recess, the T top is start signal (ignition, closer to output stud), the T vertical is indicator lamp. to ground? to 12V? Bearing (front and rear) is 15mm id 35mm OD 11mm thick. NSK 6202
4
Alternator60-01, etc1984 Chevy Caprice, 61A, NAPA #66013 (esmond has similar or same, 55A). Lower mount boss (the pivot) is 2" thick.
5
Ball joint, lower70-01FA647
6
Ball joint, upper70-01NAPA 260-1087, FA630
7
bearing, front wheel hubAllSET2 (outer, small) SET6 (inner, large). SET6 is LM67048 (bearing) + LM67010 (race).
8
bearing, rear axleAllAMC15 axle: BR6 is SET6 is ( LM67048 + LM67010 ) is AMC/Rambler front inner AND AMC/Rambler rear axle bearing.
9
bearing, throwoutroadster1993 Ford 2.3L four. fork adapted to stock Ford TO bearing. was Rambler, National 1505
10
bearing, thrust, steering knuckleallAMC 316-3284, Hoover 3061-R, Nice 608V, 7480 or 5210W. INA D7. Nice 608V available.
11
bearing, knuckle rotationallKaydon KN-121608, needles are .094 x .405.
12
belt, A/C68-01With low-mounted Sanden clone. With 4.5" drive pulley: 9425/17425, 43.25". Close fit, another 1/2" would be nice. (With 7" drive pulley: 7465, 47-1/16".)
13
belt, alternator68-0136015, Dayco 15360, NAPA 257360, Gates 7360, Goodyear 13361/15366, 36-5/8” x 25/64”
14
belt, alternatorroadsterNAPA 25-7375, 13/32" x 38-1/8".
15
belt, water pump and alternator60-01Gates 1380, 3/8" x 38". 10si type alt on bracket in generator location.
16
Borg Warner M35 filter/gasket63-10NAPA 1-4730 (ATP. 14730). has snorkel-type filter, not flat
17
Brake banjo unionroadsterBQ60, 10mm banjo hole to 3/8 NF invert flare port. 4 ea, front and rear. brakeConnect.com
18
Brake caliper, front leftroadsterNapa N4745, Wagner L107084, Ray RC4234. 1990 Chevy Celebrity
19
Brake caliper, front rightroadsterNapa N4746, Wagner L107085, Ray RC4233. 1990 Chevy Celebrity
20
Brake disc banjo boltroadsterNAPA 82703 Dorman #13940
21
Brake disc caliper support keyAllNAPA UP? 82432 for AMC small Bendix.
22
Brake disc rotor63-01KEL AR8548E:P, 1995-1997 Ford Ranger 3.0 V6 2WD front ABS. Not current roadster! Did not record part ID! In Scarebird list in notebook. Toyota Previa I think, Ranger was previous kit in 63-01.
23
Brake drum, front58..63Raybestos 2500 or 2500R, 9 x 2 (larger center hole 2-7/16). Bendix PDR0105
24
Brake drum, front68-01, 60-01Raybestos 2502, 9 x 2.5
25
Brake drum, rear58..63Raybestos 2501, 9 x 2
26
Brake hoseAllBendix 88358, same hose for all. With Scarebird/Celebrity calipers use banjo adapter. has inverted flare M and F, may work for rear with separate tee; 15.25" flange to flange.
27
Brake hose, rearroadsterDorman H36778, Ford axle, each side.
28
Brake hoses, caliper72-01Autospecialty HB-83006 (Kelsey-Hayes)
29
Brake line adapterroadster, 63-10Dorman 43301. Accepts 3/16” inverted flare tube, screws into 5/16” flare hole. (master cyl.)
30
Brake line adapter (master cyl)roadsterEdelmann 258350, DORMAN 490535. 1/2-20 male, accepts 3/16” female (standard brake line)
31
Brake line adapter (master cyl)roadsterEdelmann #258302 (summitracing.com), DORMAN Part # 7830, Dorman 490-533 (impossible). 9/16-18 male, accepts 3/16” female (standard brake line)
32
Brake master cylinderroadsterMC39027 (7/8" bore) plus adapters. was: MC39118 (1"). pushrod and ports vary. was: NAPA M2056. 1/2-20 port (“front”, closest to pushrod) 9/16-18 (“rear”). see adapters.
33
Brake master cylinder60-01Raybestos MC2796
34
Brake master cylinder63-01, 63-10, 68-01Raybestos MC36237, drums. Has 1/2-20 ports front and rear. REQUIRES ADAPTER (2) Edelmann 258350, DORMAN 490535. 1/2-20 male, accepts 3/16” female.
35
Brake pads, frontroadsterSpectra One Premium+ VSD215, EE edge code. WAS: Bosch BP215 organic; Raybestos BD215M;. 1990 Chevy Celebrity
36
Brake pads, rearroadsterVortex VSD627, EE edge code. WAS: RAYBESTOS EHT627H. 1998 Mustang 2.3L four
37
Brake rotor, frontroadsterNAPA 48-86174, Wagner BD125058, Ray 96174. 91..94 Previa w/rear drum
38
Brake self-adjuster68-01, 58..63H2516 (left), H2517 (right). For 9" drums (both). Cable has orange paint mark (shorter than 10" brakes).
39
Brake shoe68-01For 9 x 2.5 front, Raybestos 112PG (organic)
40
brake shoe spring68-019x2.5" drum shoe spring is YELLOW, H102
41
Brake spring kit58..63For Bendix front drums, shoe and hold-downs, Raybestos H7037. Does two brakes (one axle).
42
brake teeroadsterDorman 499-020.1. 3/16” inverted flare female
43
brake wheel cylinder, front58..63Raybestos WC34177 left, WC34178 right. 1" bore (port always faces rearward). 1960 Rambler (not American), 1960-66 Mopar A-Body
44
brake wheel cylinder, front60-01, 68-01, 63-01for 9x2.5 brakes, Raybestos WC37014, WC37015 (left and right), 1.125" bore. This is what's in the 60 American wagon. The RIGHT one has 1/4-28 bleeder; the LEFT one is M7x1mm.
45
brake wheel cylinder, rear58..63WC34876 (same each side)
46
brake wheel cylinder, rear70-01Raybestos WC34876, 13/16". Same both sides (centered port)
47
bushing, control arm70-01FB391 which?
48
bushing, control arm70-01FB263 which?
49
bushing, control arm, lower68-01ACDELCO 45G9016. one in a box
50
bushing, control arm, lower58..63Use upper arm part, but press carefully to 0.500" spec in TSM. The correct lower bushing is unavailable, is identical except for a press-depth-limiting rib.
51
bushing, control arm, upper68-01ACDELCO 45G8012. 2 in a box, but vague.
52
bushing, control arm, upper58..63Raybestos 565-1017, AC Delco 45G1017. 1.25" OD working diam (press-fit area, larger stepup), 1.71" long, .690" ID (11/16"). MAYBE DORMAN 532-422
53
bushing, shock absorberAllDorman 31018. contains two rubbers, for one end of one shock. Front of car needs 4 sets.
54
bushing, strut rod, kit70-01Perfect Circle, McQuay-Norris FA685; Moog FA-685? Better part?; NAPA 274-9054, MOOG K8157, MK8157 is a Ford part, with AMC instructions. Moog K3090 no longer exists, but Mevotech MK8157 does and references K3090. Dorman 531-650.
55
bushing, sway bar70-01FA1453
56
bushing, trunnion, kit68-01Prothane 1-210. polyurethane, but only choice. one kit does two trunnions.
57
cable, battery68-01UNITED 4225. 25", 4ga, good quality generic cable.
58
cable, speedometer60-01For BW M35 auto, AC brand CC-79 (1950's NORS). Has 1" diameter fat conical transmission end. 72" long. The 58" cable barely fits, tight. Is that manual trans?
59
carburetor, YFA 7112s60-01see carb pages
60
carburetor, YFA feedback 7480ssee carb pages. Rebuild kit 4317.
61
cap, oil filler68-01ACDELCO 12C19
62
cap, radiator60-01Stant 10328, 7 psi. Factory seems to have been 13 psi.
63
carburetor60-01"Yard sale" Carter YF, stamped 7112S, should be 1976 AMC Gremlin 232/258. Mike's Carburetor rebuild kit K4073, float FL32, Carter float 216-17. Accel pump shaft is 2.645, gapped section .340". Idle jet 17-20, .027" orfice, .094" OD, 1.500" long. See carb sheet for tune and maint. quadrajetparts.com float 1445B, ethanol proof accel pump 1062AE.
64
clutch kitroadster1993 Mustang 2.3L four, Sachs K0315-04. driven disc installed under AMC cover; Ford cover will require drilling flywheel but otherwise is good. see roadster T5 research page for alternatives.
65
connector, alternator, GMallNAPA VRC148, for Delco 10si
66
connector, coolant pumproadsterBeck Arnley 158-0400,. for the 0392022002 intercooler pump
67
coolant circulation pumproadsterDavies Craig EBP15, Bosch 0 392 023 004. small pump, ~27 lpm
68
coolant hose, circ pumproadsterPegasusAutoRacing.com, 90 elbow 19mm ID black.
69
Cooling Fan63-01NAPA 823-1226, Flex-A-Lite nylon, 14". requires 3/8" - 1/2" spacer; works great.
70
drive belt (elec water pump)roadsterGates 7325 (38.125”)
71
EGR valve70-01BJA 17075669 and 18812 (AMC part?). 1983 258ci engine
72
filter, air60-01CA184, in chopped 70's air hat.
73
filter, airAllNAPA 2054/WIX 42054, many AMC. 2.25" x 9.75"
74
filter, crankcase air63-10Allied Signal CA6902
75
filter, crankcase breather68-01Purolator B13153, fits in Help! grommet 42056 but will mount in 81 Spirit air cleaner
76
filter, fuel68-01Cartridge inside glass bowl, Wix 33038, is this Fram CG8? 1.916" tall, 1.508 OD, .656" hole.
77
filter, fuel60-01Cartridge inside bowl, Fram CG-7, Wix 33943 NAPA 3943, 1.89" tall, Carter double-action pump
78
filter, fuelallWIX 33032 (metal), WIX 33002 (clear), 5/16" hose nipples
79
filter, fuelallPurolator transparent filter. F21111, 3/8". F20011 5/16".
80
filter, oil68-0113/16 thread. NAPA 1258, WIX 51258, Mobile One M1-203, ACDELCO PF24. 199/232/258.
81
filter, oilroadster, 60-01WIX 51374 or 51088. 3/4-16 thread, gasket OD 2.74, ID 2.43. 51088 fits 1986 BMW 325 2.7L, 1986 M-B 190E 2.3L. NAPA Gold 1374. WIX 51374 (1988..1991 BMW M3, 2.3 L4). but don't need anti-drainback since mounted open-up.
82
fitting, hose nippleall5/16" hose to 1/8" NPT male thread (fuel pump, vacuum ports, etc). Dorman 785-412
83
gasket set, overhaulOHVFelPro 7723 B-3, unobtainium. Best RS527SA.
84
gasket, Carter YF type carburetorAllFel-Pro 60044
85
gasket, exhaust pipe flange68-01Felpro 60299, the "donut", 1-13/16" ID. later ones are larger ID
86
gasket, headOHVBest Gasket 527G, 527SA, 52527
87
gasket, oil pump, 1965 full-flowOHVFor 1965 full-flow pump and block 3A84, Best 3A84 RS574SA. Part from old Felpro overhaul kit is marked 13887, not found.
88
gasket, timing cover kit68-01Fel-Pro TCS 45458
89
gasket, transmission pan, M-3560-01BW Model 35 transmission oil pan gasket. IT IS NOT Felpro TOS 18109 INCORRECT PART.
90
gasket, valve coverOHVBest 22027E, 10057E (maker unknown)
91
Heater core60-01Not exact, but APDI 9010135, Murray 94629, 75..87 Ford F-250. Requires fab plate and moving hole.
92
Heater core63-10Ready-Aire 1211, NAPA 3107, Four Seasons 94562, Everco 2221, Stant 9206, Murray 9407
93
hose, brake63-01, roadsterNAPA 36801. front and rear (rear with tee), but substituting late part for rear
94
hose, fuelallGates 27134, 25 feet of 5/16" Barricade hose. 30R14 T1, not that 30R7 shit that melts with alcohol.
95
hose, lower, coolant pumproadster1.25” to 19mm/.75” 90 degree elbow, silicone, HPS Silicone Hoses HTSER90-075-125. Hps-siliconehoses.com
96
hose, oil lines, PTFE lined60-018AN female, 16" long, Fragola 380018, 2 each. For modified 1965 pump to remote filter. ONE END 45 DEGREES! CHECK PART NUMBER.
97
hose, radiator, lower60-01Gates 20442
98
hose, radiator, lower63-10Gates/NAPA 7310, 1.5" x 1.75" x 19.25", FLEX DOES NOT FIT
99
hose, radiator, lower70-01NAPA 7651, 60977 (Gates?) fits bigger 3-row
100
hose, radiator, lowerroadsterfor the Speedway radiator and stock pump: Dayco 81491 flex hose, works OK, 1-1/2" x 22-7/8", sharp 90 one end. WUT: the Speedway rad outlet is 1.75"?