ABCDEFGHIJKLMNOPQRSTUVWXYZAAABACADAEAFAGAHAIAJAKALAMANAOAPAQARASATAUAVAWAXAYAZBABBBCBDBEBFBG
1
2
3
4
5
User Guide for Form resin
6
For other resin user guides, please visit https://siraya.tech support section
7
Form is an affordable general model resin for laser SLA resin printers like Formlabs and Peopoly Moai.
8
It is formulated to work with both PDMS and FEP vat commonly found on laser printers. The Form offers great resolution and surface finish while it is easy to print using the suggested setting.
9
10
Due to higher polymer content for its outstanding mechanical properties, the ideal printing condition for Form is over 25C.
11
Due to Form resin is developed for laser SLA printer, it takes more energyt to cure than resins designed for MSLA/LCD printer. Please avoid using Form on MSLA printers
12
13
* Important, before printing Form
14
Form has that dark grey colors that model makers love, and we have already seen some great prints. However, it is also the only Siraya Tech resin that has pigments, and it may settle. To get the best results out of Form, SHAKE HARD (applies to all resins with pigments)

To do it correctly to shake that bottle for 20-30s before use. Stir up the resins that is already in the vat before each print. And if you just received Form, before opening it up for the first time, turn it upside down for a minute (submerged in warm water is even better) and then shake for another minute or two to make sure you get a great mix.

IF you want to take it to next level, throw a small metal ball in there and shake, the object will significantly increase the efficiency of mixing pigments and resins.
15
16
Please download profiles base for Elegoo, Anycubic, Phrozen, Peopoly, EPAX, Creality
17
https://drive.google.com/drive/folders/1eCz4_dc0fT-jfBLp4L9mKYebY90lfHHO?usp=sharing
18
19
Exposure: Form Grey
20
Recommended
21
PrinterProfile
22
Form2Grey V4
Some users run print at Dental LT for higher accuracy print
23
Form3Grey V4
Some users run print at Dental LT for higher accuracy print
24
Form1+Grey V4
Some users run print at Dental LT for higher accuracy print
25
Moai
Laser Power set to 58. Use standard slicing profile
26
27
28
Before Printing
29
It is a good practice to mix resin and expose the bottom of the vat to air before printing. This replenish oxygen in the vat and helps reduce peel force.
30
Form especially benefit from mixing because it has pigments and may settle over time
31
It would also ensure print consistency if user can get the initial resin temperature above 25 and keep the environmental temperature above 20 C
32
33
Cleaning:
34
Use a painter brush (or any brush made with hair) remove excess resins on the printed part with Use 95% concentrated Ethanol or IPA to clean.
35
Do not submerge the parts in alcohol for more than 30 seconds. After 2-3 minutes of cleaning action, remove alcohol with a hair dryer or air blower. For complex part with lots cavities, it may be a good idea to clean/dry multiple times.
36
User can check by touching the dryed surface of the part to see if it is still sticky. If the dryed surface is still sticky, wash some more and dry again.
37
38
Sanding is easy with Form. Use 1000 grit sand paper with a bit of mineral oil or water. Mineral oil adds lusters
39
40
Post Curing:
41
Form reached its optimal strength when the printed part is post-cured with UV after cleaned. Use 395-405nm UV light and cure for about 15 minutes.
42
Make sure resin is completely cleaned off and there is not alcohol left (it needs to be dry) on the print before curing.
43
Curing by submerging object in water will significantly increase curing efficiency
44
45
Mechanical Properties
46
Heat Deflection Point: 120C
47
Liquid Denisty (g/cm3) 1.13
48
Hardness (Shore D) 80
49
Tensile Strength at Break (Mpa) 60
50
Elogation at Break (%) 6
51
Young’s Modulus (MPa) 825
52
Viscocity (cps at 25c) 800-1000
53
54
55
MSDShttps://drive.google.com/file/d/1hQ-EJPGCuDp6SrYnl4VQeKm8hku_s9wK/view?usp=sharing
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100