ABCDEFGHIJKLMNOPQRSTUVWXYZ
1
2
3
4
5
6
7
8
 OSCAR RED OXIDE PRIMER 8940
9
10
Product DescriptionThis product is a primer based on Alkyd Resin and pigmented with red oxide and other suitable extenders.
This product is designed as primer for ferrous metals. It can be used for interior and exterior surfaces. This product has good adhesion to clean ferrous metals, is easy to apply and resists mildly corrosive environments.
11
Interior / Exterior
12
13
Recommended Uses- This product is designed as primer for ferrous metals. It can be used for interior and exterior surfaces.Solvent Based
14
-Ferrous metal
15
Volume Solid
16
Special Features ·        Durable50 ± 2%
17
·        Good hiding power
18
·        Good adhesion
19
·        Easy to apply
20
·        Excellent flow and levelingCoverage:
21
·        Excellent spreading on substrate10.0-16.7 m2/L
22
Product test standardsSpecific Gravity:
23
ASTM D 1475 / BS EN ISO 2811-1 : 2016
24
Gloss: Roller
25
ASTM D 523 / BS EN ISO 2813 : 2014
26
Volume Solids:
27
ASTM D 2697 / BS EN ISO 3233-3 : 2015Brush
28
Viscosity:
29
 ASTM D 562
30
Packing18 LTR Spray Gun
31
3.75 LTR
32
33
34
35
StorageStore in cool and well ventilated place protected from heat and direct sunlight. Containers must be kept tightly closed.
36
37
Flash Point > 38° CVOC - 400 g/L
38
Physical Properties
39
FinishSmooth-Flat
40
Colors Red Oxide
41
Specific Gravity1.60+/-0.02
42
Volume Solids 50 ± 2 % Surface Drying:
43
Thinner & CleanerWhite Spirit 2 Hours.@ 30° C
44
DilutionMaximmum 5%
45
Mixing RatioNot Applicable
46
Pot LifeNot Applicable
47
Shelf Life24 month when stored in original sealed container In a cool dry placeHard Drying:
48
Wet Film Thickness 60-100 µ16 hours @ 30° C
49
Dry Film Thickness 30-50 µ per each coat
50
Theoretical Coverage 10.0-16.7 m2/L per each coat
51
Spreading rate depends on applied film thickness, surface imperfections, type of surface texture, porosity of the substrate, environment temperature and wastage during application. Maximum spread rate per coat is obtained at minimum dry film thickness and vice versa. 3.75 L
52
Surface Dry2 hours at 30° C
53
Over-Coat Min 16 Hours
54
Hard dry16 hours at 30° C
55
Surface PreparationThe metal surface must be clean, dry and free from dust, oil, grease, rust or other contaminants.
Depending on the condition, the surface must be prepared according to ISO St2, ISO St3 or ISO Sa2½
56
18 L
57
58
Recommended Coating SystemStir the contents well before use. Do not apply the paint in very cold conditions, to impervious surfaces or surfaces subject to steam and condensation. It is advisable to build up coat thickness by applying in thin layers, instead of applying one single thick coat to avoid cracking Avoid painting below 10° C and humidity more than 85% .
59
Flammable
60
61
Exterior/Interior
62
On Ferrous
63
 Primer1 X Oscar Red Oxide Primer 8940
64
Top Coat2 X Oscar Enamel Flat 8690
65
66
On Metal SubstratePaint System
67
 Primer1 X Oscar Red Oxide Primer 8940
68
Top Coat2 X Oscar Enamel Flat 8690Splashes on eye- wash with Water
69
70
71
72
73
Application DataGuidelines for Airless Spray Application
74
Nozzile Orifice : 0.017" - 0.019"
75
Spray Angle : 65° -80°
76
Nozzile Pressure : 140-150 kg/cm2 (2175psi)
77
78
Health and SafetyEnsure good ventilation during application and drying.
79
Avoid contact of the product with skin and eyes by using proper gloves, apron , goggles and mask.Splashes on Skin-wash with soap & hot water
80
If splashes enter eyes wash with plenty of water.
81
Keep out of reach of children.
82
Remove splashes from skin with soap and warm water.
83
In case of insufficient ventilation during spraying, wear suitable respiratory equipment.
84
Do not breathe vapour / spray.
85
86
DISCLAIMERThe above information is based on internal testing and our accumulated experience. This information is given in good faith but without warranty as the conditions under which the product is used are often beyond our control. This data sheet supersedes those previously issued and may be changed without prior notice.
87
Disclaimer
88
89
90
91
92
93
94
95
96
97
98
99
100