BTB Resin Settings

	A	B	C	D	E	F	G	H	I	J	K	L	M	N	O	P	Q	R	S	T	U	V	W	X
1	TIPS:
2	- Remember to correcty CALIBRATE your PRINTER
3	- Always SHAKE your RESIN before start printing
4
5	PRINTER BRAND	PRINTER MODEL	RESIN BRAND	RESIN TYPE	STATUS	DATE	PATRON	RELEASE	MODEL	Layer Height	Bottom Layers	Transition Layers	Transition Type	Exposure Time	Bottom Exposure Time	Light-off Delay	Bottom Light-off Delay	Bottom lift Distance	Lifting Distance	Bottom Lift Speed	Lifting Speed	Retract Speed	Room Temp. (ºC)	Comments
6	AnyCubic	Photon	AnyCubic	Grey		20/01/2021	Bite the Bullet	Jul 20 - Jan 21	Multiple	30 µm	8	0	Linear	11,0 s	60 s	1 s	1 s	5 mm	5 mm	55 mm/min	55 mm/min	140 mm/min	20,0 ºC
7	Phrozen	Sonic Mighty 4K	AnyCubic	Grey		20/01/2021	Bite the Bullet	Jan 21 - Mar 21	Multiple	30 µm	6	6	Linear	2,5 s	30 s	10 s	10 s	7 mm	7 mm	70 mm/min	70 mm/min	150 mm/min	20,0 ºC
8	Phrozen	Sonic Mighty 4K	Phrozen	Aqua Resin Gray 4K		20/04/2021	Bite the Bullet	Mar 21 - Current	Multiple	30 µm	8	4	Linear	2,0 s	30 s	11 s	11 s	8 mm	6 mm	60 mm/min	60 mm/min	150 mm/min	20,0 ºC
9	Elegoo	Mars	Elegoo	ABS-Like Grey		23/01/2021	...	All	Multiple	30 µm	8	0		9,5 s	70s	0 s	0 s	7 mm	5 mm	35 mm/min	240 mm/min	240 mm/min	20,0 ºC	Temperature 20+
10	Elegoo	Mars Pro	Siraya Tech	Sculpt Grey		24/01/2021	IT Xaumby	Dec-Jan	Multiple	30 µm	5	0		14,0 s	75 s	0 s	0 s	5 mm	5 mm	40 mm/min	180 mm/min	150 mm/min	22,0 ºC	Slower resin but very consistent results. Must be warm for good results. 2x-3x curing time after print.
11	Elegoo	Mars Pro	AnyCubic	Grey		24/01/2021	IT Xaumby	Dec-Jan	Multiple	30 µm	5	0		7,0 s	50 s	0 s	0 s	5 mm	5 mm	40 mm/min	50 mm/min	150 mm/min	22,0 ºC	I use these settings for any thin resins as a baseline. If it feels strong enough I will increase lift speed to 180mm/min
12	Elegoo	Mars pro 2	Monocure3d	rapid red and green		04/02/2021	James Jefferson	All	Multiple	30 µm	4	0		2,3 s	16 s	11 s	11 s	9 mm	9 mm	40 mm/min	180 mm/min	180 mm/min	20,0 ºC	my general setting for Monocure resins. ill increase the exposure by .1 if i increase layers. 30sec cure time usually sufficiant.
13	Phrozen	SMini4K	Monocure3d	rapid red and green		04/02/2021	James Jefferson	All	Multiple	30 µm	4	1	Linear	2,3 s	20 s	12 s	12 s	6 mm	6 mm	40 mm/min	180 mm/min	180 mm/min	20,0 ºC	I also use a whambam with my phrozen
14	Creality	LD-002H	elegoo/anycubic	clear/transparent ABS-like		08/02/2021	Xan		Multiple	30 µm	8	0		2,0 s	12 s	0 s	0 s	5 mm	5 mm	100 mm/min	300 mm/min	300 mm/min	25,0 ºC	My goto settings for all mini prints
15	Creality	LD-002R	Monocure3D	rapid gunmetal grey		20/02/2021	Kal	January 2021	Barath	40 µm	5	0		6,5 s	45 s	1 s	1 s	6 mm	6 mm	60 mm/min	60 mm/min	60 mm/min	25,0 ºC
16	Phrozen	Sonic Mini 4k	Esun	PLA bio resin gray		10/03/2021	Clara	All	Multiple	30 µm	9	0	Linear	3,1 s	23 s	0 s	0 s			60 mm/min	45 mm/min	60 mm/min	25,0 ºC	bottom layers are hell to remove, but so far,very few failed prints
17	Phrozen	Sonic Mini 4k	Siraya Tech	Fast Grey		09/03/2021	Astounding	February 21	Goblins	40 µm	4	0		2.5	25 s	0 s	0 s	6 mm	6 mm	240 mm/min	240 mm/min	240 mm/min	18,0 ºC	First try with Vroom settings. Best resin I've used yet.
18	Phrozen	Sonic Mighty 4k	Siraya Tech	Fast Grey/Tenacious (80/20)		08/03/2021	OtterProper		Multiple	30 µm	6	0		2.5 s	30 s	13 s	13 s	9 mm	9 mm	240 mm/min	240 mm/min	240 mm/min	22,0 ºC	post-proc: sonic cleaner 15mins @ 35ºC, then 3mins ISO wash, trim supps, lightly brush and dry, UV cure, airbrush prime. Next.
19	Creality	LD-002R	Siraya Tech	Fast Smoky Black		10/05/2021	Kal	May 21	Multiple	50 µm	10	0		9,0 s	50 s	0 s	0 s						24,0 ºC	Best Resin I've used
20	Phrozen	Sonic Mini 4k	Siraya Tech	Epax Hard Grey/Tenacious (80/20)		20/06/2021	DesertDweller55	June 21	Multiple	20 µm	6	0	Linear	2.4	18 s	0 s	0 s	8 mm	6 mm	50 mm/min	50 mm/min	130 mm/min	20,0 ºC	Multiple Stress Tests - Best Result
21	Creality	Photon Mono X	Siraya Tech	Epax Hard Grey/Tenacious (80/20)		20/06/2021	DesertDweller55	June 21	Multiple	20 µm	6	0		2,0 s	18 s	0 s	0 s	8 mm	6 mm	50 mm/min	50 mm/min	130 mm/min	20,0 ºC	Concurrent tests with Above PSM4K tests
22	Phrozen	Sonic Mini 4k	3D Resin Solutions	Fast+ Cool Grey		24/06/2021	DesertDweller55	May 21	Ranger	30 µm	6	0		2,2 s	30 s	0 s	0 s	9 mm	7 mm	50 mm/min	50 mm/min	130 mm/min	20,0 ºC	Fast+ is thicker than normal. It has more impact resistance than normal but not much.
23	Phrozen	Sonic Mini 4k	Siraya Tech	Navy Grey		28/07/2021	Treebeard	July 21	4Dragonborn/3Lilith	40 µm	4	0		2.8	28 s	5 s	5 s	10 mm	6 mm	35 mm/min	240 mm/min	240 mm/min	20,0 ºC	Quality of resin is similar to ST Fast Grey, but visibilty is far superior. Requires 20% more exp time. Less post cure.
24	Creality	Halot-One	Esun	Sky Blue	NEW	27/12/2021	Pendrayk		Multiple	50 µm	4	0		3,5 s	22 s	1 s	1 s	6 mm	6 mm	180 mm/min	180 mm/min	180 mm/min	20,0 ºC	Need to use craft knife blade to get mini off the build plate, dropped the initial layer exposure time by 1s and seems to have made a difference allowing easier removal from build plate
25	Creality	Halot-One	Monocure3D	Grey		15/02/2023	Pendrayk		Multiple	50 µm	4			4,7 s	45 s	1 s	1 s	6 mm	6 mm	180 mm/min	180 mm/min	180 mm/min	28,0 ºC
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100