Easy by Siraya Tech - user guide
 Share
The version of the browser you are using is no longer supported. Please upgrade to a supported browser.Dismiss

View only
 
 
ABCDEFGHIJKLMNOPQRSTUVWXYZ
1
2
3
4
5
User Guide for Easy
For other resin user guides, please visit https://siraya.tech support section
6
7
Easy is developed to be an affordable general application resin ideal for model making like tabletop minis, and figurines.
8
It is not a tough or engineering resin but can be mixed with Blu/Tenacious for more impact resistant.
9
10
While the ideal printing condition for Easy is over 20C, we have printed as long as 15C as long as the bottom layers uses more exposure time
11
12
13
Best print with recommended support setting, see below
14
15
Exposure
16
Recommended
Resin Temperture 25-35C
Room temperature 20-25C
17
PrinterLayer HeightExposure (s)
# of Initial Layers
Exposure for Init Layers
Exposure (s)
# of Initial Layers
Exposure for Init Layers
Note
18
Photon50um11-12 (s)460 s12-13 (s)690 s
19
EPA X150um9 (s)445 s9 (s)675 s
20
EPA X1100um12 (s)475 s12 (s)690 s
21
Shuffle50um9(s)575 s
22
Shuffle XL50um12(s)575 s
23
D750um9(s)575 s
24
Inkspire50um12-13 (s)690 s
Inkspire does not specify its light output, one user told us it is very closely to Photon
25
Photon S50um11s560s12s690s
26
27
28
Before Printing
29
It is a good practice to mix resin and expose the bottom of the vat to air before printing. This replenish oxygen in the vat and helps reduce peel force.
30
31
It would also ensure print consistency if user can get the initial resin temperature above 25 and keep the environmental temperature above 20 C
32
33
Recommend best support settings:
34
Make sure the support tip diameter is 1.2mm for larger prints with a depth of 0.5mm. See more full settings recommended
35
https://www.facebook.com/groups/sirayatech/permalink/290257771885611/
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
It is best to use island style base like below left, not the raft style on the right. If you have problem keeping first layer on, make sure you level again to minimize gap between build plate and LCD screen
67
68
Island base ->
69
Raft base ->
70
71
72
73
74
75
76
77
78
79
Cleaning:
80
Use a painter brush (or any brush made with hair) remove excess resins on the printed part with Use 95% concentrated Ethanol (preferred) or IPA to clean. Some form of methnol should work but make sure it does not contain acetone.
81
Do not submerge the parts in alcohol for more than 30 seconds. After 2-3 minutes of cleaning action, remove alcohol with a hair dryer or air blower. For complex part with lots cavities, it may be a good idea to clean/dry multiple times.
82
User can check by touching the dryed surface of the part to see if it is still sticky. If the dryed surface is still sticky, wash some more and dry again.
83
84
Post Curing:
85
Easy reached its optimal strength when the printed part is post-cured with UV after cleaned. Use 395-405nm UV light and cure for about 15 minutes.
86
Make sure resin is completely cleaned off and there is not alcohol left (it needs to be dry) on the print before curing.
87
Curing by submerging object in water will significantly increase curing efficiency
88
89
Mechanical Properties
90
​Shore D 90
91
Tensile Strength 35Mpa
92
Young’s Modulus 800Mpa
93
Elongation At Break: 8.5%
94
95
96
msds
97
https://drive.google.com/open?id=10jGDee_fYSWe6GQdGVJ-7NnwH7Iiru2V
98
99
100
Loading...