BOM.xlsx

	B	C	D	E	F
1
2
3	No	Name	Value	Layer	Note
4
5	1	C1	100uF 10V	Up	Can be 10uF to 100uF, 6.3V to 25V
6	2	C2	100uF 10V	Up	The same
7	3	C3	0.33uF 1206	Down	Can be 0.1...0.33uF
8	4	C4	0.33uF 1206	Down	Can be 0.1...0.33uF
9	5	C5	0.33uF 1206	Down	Can be 0.1...0.33uF
10	6	C6	100uF 10V	Up	Can be 10uF to 100uF, 6.3V to 25V
11	7	C7	0.33uF 1206	Up
12	8	C8	220pF 1206	Up	Can be 150...470pF
13	9	C9	220pF 1206	Up	Can be 150...470pF
14	10	DA1	AMS1117-3.3 sot223	Up	Any sot223 1117-3.3, for example LM1117-3.3, LD1117-3.3
15	11	DQ1	EPM3064ATC44 TQFP44	Up
16	12	DQ2	Atmega8a TQFP32	Up	Can be replaced with Atmega8L
17	13	FB1	>= 1000 Ohm 1206	Up	Ferrite bead. Can be replaced with resistor 0...100 Ohm
18	14	FB2	>= 1000 Ohm 1206	Up	Ferrite bead. Can be replaced with resistor 0...100 Ohm
19	15	FS1	Self recovery fuse 500mA 1812	Up
20	16	JP1	Pin header 2x6 2.54mm	Up
21	17	JP2	Pin header 2x4 2.54mm	Up
22	18	R1	1k 1206	Up	Install only this resistor or RN1, not both!
23	19	R2	1k 1206	Up	Install only this resistor or RN1, not both!
24	20	R3	1k 1206	Up	Install only this resistor or RN1, not both!
25	21	R4	1k 1206	Up	Install only this resistor or RN1, not both!
26	22	R5	560	Up	Can be 470...680 Ohm
27	23	R6	2k 1206	Up	Can be 2...4.7K
28	24	R7	2k 1206	Up	Can be 2...4.7K
29	25	R8	2k 1206	Up	Can be 2...4.7K
30	26	R9	do not install	Up
31	27	RN1	1K resistor array 0603*4	Down	Install only this resistor or R1, R2, R3, R4
32	28	VD1	LED 3mm green	Up
33	29	XS1	Pin header 7x1 2.54mm	Up	For burning firmware Altera EPM3064
34	30	XS2	Pin header 6x1 2.54mm	Up	For burning firmware Atmega8
35	31	XS3	do not install	Up
36	32	XS4	PS/2 connector	Up
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100