A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | AA | |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | KTH PrototypeCenter - Ultimaker Material Settings | ||||||||||||||||||||||||||
2 | |||||||||||||||||||||||||||
3 | This document is read-only for the general public, but can be edited by Prototype Staff | ||||||||||||||||||||||||||
4 | If you have any suggested edits, please email prototype@kth.se | ||||||||||||||||||||||||||
5 | |||||||||||||||||||||||||||
6 | last revised 11/2017 | ||||||||||||||||||||||||||
7 | |||||||||||||||||||||||||||
8 | General suggestions to how to get the best results! | ||||||||||||||||||||||||||
9 | http://support.3dverkstan.se/article/28-material-guide | ||||||||||||||||||||||||||
10 | In Ultimaker 2 and 2+ you can manually adjust the material settings for each print. However, in the Ultimker 3s, they pushed more of the material settings to be set in Cura instead. When you select the material on an Ultimaker 3, you are really only choosing the nozzle temperature - setup your material in Cura! | ||||||||||||||||||||||||||
11 | |||||||||||||||||||||||||||
12 | material | printing T (C) | build plate T (C) | retraction | fan (%) | print speed | flow (%) | spring length | build plate adhesion | note | Link | ||||||||||||||||
13 | PLA | 210 | 60 | enabled | 100 | 80 mm/s is usually fine | 100 | 10.5mm compressed | For most models a clean and well calibrated build plate is enough. Large models may require brim and a thin layer of glue (glue stick) on the build plate. | https://ultimaker.com/en/resources/22225-how-to-print-with-ultimaker-pla | |||||||||||||||||
14 | FPE45D | 220 | 100 | disabled | 30 | 50 mm/s? | 100 | 12mm compressed | It is important to use brim and a thick layer of glue (glue stick) otherwise the model will not stick tothe build plate. | ||||||||||||||||||
15 | NINJAFLEX | 235 | 45 | disabled | 50 | 30 mm/s (this is slow!) | 100 | 13.5mm compressed | For most models a clean and well calibrated build plate is enough. Large models may require brim and the thin layer of glue (glue stick) on the build plate. | works best with 0.8mm nozzle | https://ninjatek.com/products/filaments/ninjaflex/ | ||||||||||||||||
16 | ABS | 250 | 100 | 50 | 95 | I don' think glue works on the bed | |||||||||||||||||||||
17 | PETG | 240 | 70 | not available as a setting in Ultimaker 3, select CPE to start something close, and look up properties online | |||||||||||||||||||||||
18 | |||||||||||||||||||||||||||
19 | |||||||||||||||||||||||||||
20 | |||||||||||||||||||||||||||
21 | |||||||||||||||||||||||||||
22 | |||||||||||||||||||||||||||
23 | |||||||||||||||||||||||||||
24 | |||||||||||||||||||||||||||
25 | |||||||||||||||||||||||||||
26 | |||||||||||||||||||||||||||
27 | |||||||||||||||||||||||||||
28 | |||||||||||||||||||||||||||
29 | |||||||||||||||||||||||||||
30 | |||||||||||||||||||||||||||
31 | |||||||||||||||||||||||||||
32 | |||||||||||||||||||||||||||
33 | |||||||||||||||||||||||||||
34 | |||||||||||||||||||||||||||
35 | |||||||||||||||||||||||||||
36 | |||||||||||||||||||||||||||
37 | |||||||||||||||||||||||||||
38 | |||||||||||||||||||||||||||
39 | |||||||||||||||||||||||||||
40 | |||||||||||||||||||||||||||
41 | |||||||||||||||||||||||||||
42 | |||||||||||||||||||||||||||
43 | |||||||||||||||||||||||||||
44 | |||||||||||||||||||||||||||
45 | |||||||||||||||||||||||||||
46 | |||||||||||||||||||||||||||
47 | |||||||||||||||||||||||||||
48 | |||||||||||||||||||||||||||
49 | |||||||||||||||||||||||||||
50 | |||||||||||||||||||||||||||
51 | |||||||||||||||||||||||||||
52 | |||||||||||||||||||||||||||
53 | |||||||||||||||||||||||||||
54 | |||||||||||||||||||||||||||
55 | |||||||||||||||||||||||||||
56 | |||||||||||||||||||||||||||
57 | |||||||||||||||||||||||||||
58 | |||||||||||||||||||||||||||
59 | |||||||||||||||||||||||||||
60 | |||||||||||||||||||||||||||
61 | |||||||||||||||||||||||||||
62 | |||||||||||||||||||||||||||
63 | |||||||||||||||||||||||||||
64 | |||||||||||||||||||||||||||
65 | |||||||||||||||||||||||||||
66 | |||||||||||||||||||||||||||
67 | |||||||||||||||||||||||||||
68 | |||||||||||||||||||||||||||
69 | |||||||||||||||||||||||||||
70 | |||||||||||||||||||||||||||
71 | |||||||||||||||||||||||||||
72 | |||||||||||||||||||||||||||
73 | |||||||||||||||||||||||||||
74 | |||||||||||||||||||||||||||
75 | |||||||||||||||||||||||||||
76 | |||||||||||||||||||||||||||
77 | |||||||||||||||||||||||||||
78 | |||||||||||||||||||||||||||
79 | |||||||||||||||||||||||||||
80 | |||||||||||||||||||||||||||
81 | |||||||||||||||||||||||||||
82 | |||||||||||||||||||||||||||
83 | |||||||||||||||||||||||||||
84 | |||||||||||||||||||||||||||
85 | |||||||||||||||||||||||||||
86 | |||||||||||||||||||||||||||
87 | |||||||||||||||||||||||||||
88 | |||||||||||||||||||||||||||
89 | |||||||||||||||||||||||||||
90 | |||||||||||||||||||||||||||
91 | |||||||||||||||||||||||||||
92 | |||||||||||||||||||||||||||
93 | |||||||||||||||||||||||||||
94 | |||||||||||||||||||||||||||
95 | |||||||||||||||||||||||||||
96 | |||||||||||||||||||||||||||
97 | |||||||||||||||||||||||||||
98 | |||||||||||||||||||||||||||
99 | |||||||||||||||||||||||||||
100 |