File Specifics (Please Reference Previous Two Sections)

Comments/Questions (If you have more specific color requests, specific strength requirements, etc., please leave them here)

So hi jeffrey:) this is our first print woo. This will be on of our Bonus hands to take to hand camp, and we are just testing the scaling out:)

- left_palm done
- pins done
- clip, cap, tensioner done
- finger tips, proximals, and gauntlet printing

-- 1x raptor_reloaded_left_palm_supported.stl, no color preference, 120%
-- 2x raptor_reloaded_knuckle_pin.stl, no color preference, 120%
-- 1x raptor_reloaded_thumb_pin.stl, no color preference, 120%
-- 5x raptor_2.0_proximal.stl, no color preference, 120%
-- 5x raptor_2.0_finger_pin.stl, no color preference, 120%
-- 5x raptor_2.0_fingertip.stl, no color preference, 120%
-- 1x raptor_reloaded_gauntlet_supported.stl, no color preference, 120%
-- 2x raptor_reloaded_wirst_pin.stl, no color preference, 120%
-- 2x raptor_reloaded_wrist_pin_cap.stl, no color preference, 120%
-- 1x raptor_reloaded_tensioner.stl, no color preference, 120%
-- 1xraptor_reloaded_retention_clip.stl, no color preference, 120%
-- 5x raptor_reloaded_tensioner_pin.stl, no color preference, 120%

Color irrelevant, upscale by factor of 3 (overall height should be roughly 30 mm)

finger cover has a bit of supports that will need to be removed

Color irrelevant, all parts should be 100%. The ball should be about 28 mm tall, if not then scale to be around that

raptor_reloaded_right_palm_supported.stl (1x) – orange, 130%
raptor_reloaded_knuckle_pin.stl (2x) – orange, 130%
raptor_reloaded_thumb_pin.stl (1x) – orange, 130%
raptor_2.0_proximal.stl (5x) – orange, 130%
raptor_2.0_finger_pin.stl (5x) – orange, 130%
raptor_2.0_fingertip.stl (5x) – orange, 130%
raptor_reloaded_gauntlet_supported.stl (1x) – orange, 130%
raptor_reloaded_wirst_pin.stl (2x) – orange, 130%
raptor_reloaded_wrist_pin_cap.stl (2x) – orange, 130%
raptor_reloaded_tensioner.stl (1x) – orange, 130%
raptor_reloaded_retention_clip.stl (1x) – orange, 130%
raptor_reloaded_tensioner_pin.stl (5x) – orange, 130%

I wrote how many of each part we need printed next to the part names (E.g.: raptor_2.0_finger_pin.stl (5x) – orange, 130% = print 5 of these parts)

# of each part needed is listed in file specifics (e.g. (5x) = 5 of this part needed)

Color irrelevant. Units in millimeters, all parts should be 100%. For reference, height of stem should be about 22 mm.

These parts will be under higher stress. If possible, increase infill percentage (40%?). Would like to have it done by Wednesday evening.

These are button stands for Adaptathon, but with screw holes in the top. We need 30 of the double stands, and 8 of the single stands.

No color preference. Units in inches, 100% (height should be about 0.45 in). Requesting quantity of 6.

No color preference, but is it possible for all parts to be the same color?

1x - raptor_reloaded_right_palm_supported.stl – no color preference, 135%
2x - raptor_reloaded_knuckle_pin.stl – no color preference, 135%
1x - raptor_reloaded_thumb_pin.stl – no color preference, 135%
5x - raptor_2.0_proximal.stl – no color preference, 135%
5x - raptor_2.0_finger_pin.stl – no color preference, 135%
5x - raptor_2.0_fingertip.stl – no color preference, 135%
1x - raptor_reloaded_gauntlet_supported.stl – no color preference, 135%
2x - raptor_reloaded_wirst_pin.stl – no color preference, 135%
2x - raptor_reloaded_wrist_pin_cap.stl – no color preference, 135%
1x - raptor_reloaded_tensioner.stl – no color preference, 135%
1x - raptor_reloaded_retention_clip.stl – no color preference, 135%
5x - raptor_reloaded_tensioner_pin.stl – no color preference, 135%

The socket parts are final and will be under moderate stress. 40-50% infill? Ball part is fine at 10-20% as it is a test part.

Gray isn't listed on there, but the recipient requested this. Specifically, they wanted a gray that resembles metal (normal gray or dark gray as opposed to something light). If you need more info slack me (Megan Yip) and I can send reference pictures of the color that the recipient requested. Thanks you!

Please prioritize this as its for a recipient and needs to be painted before it is strung.

Ball and Socket Joint. Same as before, it's just that the previous socket didn't print well, some of the plastic was sagging at the bottom.

The socket parts will definitely need support material if that wasn't being used before. Percent fill of ~40% for socket parts, ball and stem can stay at ~20%.

Support filament necessary for both. Joint components of both parts will be under compressive stress, requesting infill of ~40%.

30% infill and 1.5mm wall thickness
Also if you could keep each finger separate from the others after they're printed, that would be awesome (but not a big deal)

Thank you so much!!!

Gray if possible please because the recipient requested it. Also, I requested 2 cuffs because we had some issues the first time and I just want to have a backup piece in case anything goes wrong. Thank you!

Likely just for testing purposes. Would appreciate if we could get this expedited for Thursday 2/2 as I forgot to submit earlier

Good luck removing supports I don't want to break it lol

tensioner, fingerplate, fingerhingeplate printed; gauntlet, handbody printed

Team 102 Unlimbited Arm (Hand Camp recipient)

The 120% sizing ended up being perfect!

35% infill please per Unlimbited's guidelines

Unlimbited says that palm and cuff will need supports. Palm they typically add 2-3 rows of support in the middle of the palm area to help with bridging and for cuff they use autogenerated.
Additional print settings - 3 perimeter shells, 3 top and bottom layers (idk what this means but figured I'd include it if it helps you lol)

Thank you!!

Sorry there's so many pieces! Testing out which pieces would work best

Kellen McKenney and Kathryn Kalouf

We submitted a print request for this same clip earlier, but we think it was printed at 100% instead of 120%

I am not sure if 20% is the best scale option so if you think a different scale would be better feel free to change it :)

The palm that was printed failed because the printer ran out of filament:( (If you want to see it, it is in the Team 102 bin)

Hoping to get this in by my meeting Thursday 3/2 so that we can assemble the hand part!!

Sorry this is annoying. Elbow pins were too small but the wrist ones fit perfectly (I am confused lol)

it was printed but then i lost it, another one is printing on a printer

does not have to be strong, we just want to see what the overall shape will be like

could this get printed by this thursday 3/9/23? would be amazing hehe

These are for prototyping, not final. There are 2 different items we call jack grips, each has 2 parts. They will fit together and be secured with velcro. They will be used by children and placed on the jack of a headphone cable to allow folks with disabilities to grab it.

We meet Thursday afternoon and I'll need these before then, if at all possible. All parts should fit on the same bed. These are just for prototyping, not the final product.

put in order for pink pla filament today, will message you when I'm told we get it, thanks!

HAND CAMP PRIORITY <3 Thank you so so much, this is finally the last print!

Assortment of colors if possible, print 10 please. Prioritize the keychains I submitted previously though <3

Could you make the infill slightly more than you typically do? Maybe like 5% more infill than regular. This is the final print for our team.

Please print ASAP, would like to have by tomorrow if possible, if not though no worries

Would hopefully like to be able to start building the two hands my next meeting 4/12 :)

Thank you! If these could get printed by Tuesday 4/25 that would be great :)