ABCDEFGHIJKLMNOPQRSTUVWXYZAAABACADAEAFAGAHAIAJAKALAMANAOAPAQARASATAUAVAWAXAYAZBABBBCBDBEBFBG
1
2
Shake the bottle and mix the resin in the vat before start printing!
3
4
5
User Guide for Craft - Glow in Dark
6
For other resin user guides, please visit https://siraya.tech support section
7
The Craft – Glow In The Dark resin is ideal for applications that require print to emit light in the darkness.The
resin can be activated with UV light, Sunlight or even flashlights from smartphones.
8
10
The ideal printing condition for Craft is over 25C as it improves curing speed and lowers viscosity.
11
12
Best print with recommended support setting, see below
13
14
Please download profiles base for Elegoo, Anycubic, Phrozen, Peopoly, EPAX, Creality
15
https://drive.google.com/drive/folders/1eCz4_dc0fT-jfBLp4L9mKYebY90lfHHO?usp=sharing
16
17
Exposure Setting
18
Recommended
Resin Temperture 25-35C
19
PrinterLayer HeightExposure (s)# of Initial LayersExposure for Init Layers
20
Photon50um12 (s)460 s
21
Peopoly Phenom
use Peopoly Deft profile for your printer type in Chitubox
22
EPA X150um9.5 (s)455 s
23
Shuffle50um
24
Shuffle XL50um
25
Mars 2 Pro50um2s525
26
Mars50um9.5 (s)455 s
27
Photon Mono50um2s525
28
Mono X50um2s525
29
30
Glow-in-the-dark effect
31
The glow be activated via the use of common household light sources, including LED and flourecent light. A quick charge of a minute in close range (10cm) can give good effect.
32
UV Light can also be used to add energy to the printed object and depending on energy level, 30 seconds to a minute can be ample when done in clsoe range.
33
The glow effect can last up to 4 hours in dark environment while the glow diminishes over time.
34
35
Recommend best support settings:
36
37
We recommend medium preset support setting in chitubox for smaller prints. Heavy support for large prints on large priners
38
If you don't use chitubox, at least download a copy and see the detail settings for each preset and copy them over to your software of choice
39
40
Cleaning:
41
Use a painter brush (or any brush made with hair) remove excess resins on the printed part with Use 95% concentrated Ethanol (preferred) or IPA to clean. Some form of methnol should work but make sure it does not contain acetone.
42
Do not submerge the parts in alcohol for more than 30 seconds. After 2-3 minutes of cleaning action, remove alcohol with a hair dryer or air blower. For complex part with lots cavities, it may be a good idea to clean/dry multiple times.
43
User can check by touching the dryed surface of the part to see if it is still sticky. If the dryed surface is still sticky, wash some more and dry again.
44
45
Post Curing:
46
Craft reached its optimal strength when the printed part is post-cured with UV after cleaned. Use 395-405nm UV light and cure for about 1-2 minutes.
47
Make sure resin is completely cleaned off and there is not alcohol left (it needs to be dry) on the print before curing.
48
It is important to dry the print made by Craft completely before post curing. There is no need to use submerge in water technique with Craft
49
50
Mechanical Properties
51
​Shore D 84
52
Tensile Strength 43Mpa
53
Young’s Modulus 950Mpa
54
Elongation At Break: 2.5%
55
Viscosity:330cps
56
Heat Deflection Temperature: 65C
57
MSDS
58
https://drive.google.com/file/d/16QS62kBDGB1EH4AS_743MzeuH3ItvtkY/view?usp=sharing
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101