| A | B | C | D | E | F | G | H | I | J | K | |
|---|---|---|---|---|---|---|---|---|---|---|---|
1 | D3D Pro SHIPPING CHEAT SHEET | By/Date: | |||||||||
2 | CUT | 11 packs total | NOTES | NOTES | |||||||
3 | 4 | 4 | 13" 8mm rod, smooth | 1 | HARDWARE AND TOOL BAG | ||||||
4 | 6 | 6 | 17.5” 8 mm rod, smooth | 1 | 27 | m6x18 zinc plated socket screw | |||||
5 | 5 | 5 | 14” 8mm rod, can be any steel | 1 | 12 | m6x30 zinc plated socket screw | |||||
6 | 12 | 12 | 1/8"x1.5"x10" angle | 1 | 1 | m6x25 zinc plated socket screw | |||||
7 | 4 | 4 | cut 4 strips, 1/16"x2"x7.5" | 1 | 13 | m6 zinc plated nut | |||||
8 | 2 | 2 | pick steel plates, 1/8"& 1/16" by 8" | 1 | 18 | 6mm x 10 mm set screws | |||||
9 | 1 | 1 | Drill center of 1/16" plate, ¼” bit | 1 | 15 | m3x25 SS socket head screw | |||||
10 | 1 | 1 | Weld on long-nut on the ⅛” plate | 1 | 22 | 8 mm linear bearing | |||||
11 | 1 | 1 | weld rest of heater box | 1 | 15' 6" | GT2 belt, 6mm wide | |||||
12 | 1 | 1 | Grind plates, angle, rods | 1 | 5 | GT2 pulley, 5mm bore, 6mm wide, 20 teeth, 2 set screws | |||||
13 | 19 | 19 | paint frame members, 5 rods, box | 1 | 10 | m6x12x4 flanged bearing | |||||
14 | 1 | 1 | 14'4" belt | 1-hardware bag | 1 | 14' | nichrome | ||||
15 | 1 | 1 | 10' Fiberglass Sleeve | hardware bag | 1 | 30 | zip ties for wire management | ||||
16 | 1 | 1 | cut 8”x8” PEI | 1 | 10' | fiberglass sleeve | |||||
17 | 1 | 1 | Double-sided adhesive, stick it on | 1 | 32" | 200C wire, 18 ga, with attached fence wire | |||||
18 | 1 | 1 | 14' 26 ga nichrome wire | 1 | 1 | SD card | |||||
19 | 1 | 1 | Filament Sample | 2-plastic bag | 1 | EXTRUDER (SEPARATE BAG INSIDE OF HARDWARE bag) | |||||
20 | 1 | 1 | 48" Split Wire Loom, ½" | plastic bag | 1 | 2 | 0.4, 0.8 nozzles (1.0+ is already on heater block) | ||||
21 | 2 | 2 | make 15 rod bundle 4+6+5 and pack | 3-rods | 1 | 1 | 608 ZZ skate bearing | ||||
22 | 3 | 3 | make angle bundle and pack | 4-angle | 1 | 1 | main aluminum heat sink | ||||
23 | PICK | 1 | 1 | spring for extruder | |||||||
24 | 1 | RAMPS assembly + LCD + SD | 1 | 1 | mk7 drive gear | ||||||
25 | 6 | Stepper wires + Stepper motors | 1 | 2 | m3x30 cap head screw, heat sink | ||||||
26 | 2 | endstops | 1 | 6 | m3x18 cap head screw, idler + blower | ||||||
27 | 1 | Z probe | 1 | 1 | m3x8 cap head screw, main attachment of motor | ||||||
28 | 1 | GFCI + Plug + 5V plug + USB cable | plug up to nut | 1 | 2 | 2.9x13mm self tapping screws for fan | |||||
29 | 1 | SSR + Power Supply | 1 | 1 | fan heat sink | ||||||
30 | 1 | Heater Block assembly + extra thermistor | 1 | 1 | heater sock | ||||||
31 | 1 | Fan + blower assemblies | 1 | 1 | thin m6 nut | ||||||
32 | 1 | SSR signal + 5V signal + 24V power wires | 1 | 1 | thermal grease | ||||||
33 | TEST CONTROLLER: STEPS | 1 | PICK 3D PRINTED PARTS | ||||||||
34 | 1 | [6] Stepper Motors to RAMPS. | 1 | 4 | Frame Corners, plain | ||||||
35 | 2 | [3] endstops (one is Z probe). | 1 | 2 | left hand corners | ||||||
36 | 3 | [3] extruder heater, blower, and SSR signal | 1 | 2 | right hand corners | ||||||
37 | 4 | [3] RAMPS Power Plug (3 wire sets) | 1 | 2 | Z axis base attachment | ||||||
38 | 5 | [2] thermistors | 1 | 2 | Z axis top attachment | ||||||
39 | 6 | LCD screen | 1 | 5 | One Piece Motor | ||||||
40 | 7 | Plug in 2 plugs into GFC and connect. Ready for power. | 1 | 2 | Bed Support Carriage | ||||||
41 | test | check fan, 2 temps. Bed heat, extruder heat, motors. | 1 | 1 | One Piece Carriage | ||||||
42 | test | Test blower. Extruder motor M302 S0. Set voltages. | 1 | 1 | Y1 New Carriage | ||||||
43 | PACK AFTER TEST | 1 | 1 | Y2 New Carriage | |||||||
44 | 1 | fill heat bed + pack with bed surface | 5-heat bed | 1 | 5 | Carriage Closure | |||||
45 | 1 | usb, plug assy, gfci, SSR | 6-Power Bag | 1 | 5 | One Piece Idler | |||||
46 | 1 | controller | 7-controller | 1 | 8 | 4 autopar / 2 end / 2 x hold | |||||
47 | 1 | wires | 8-wires | 1 | 4 | bedholder pieces | |||||
48 | 1 | electronic components | 9-components | 1 | 1 | 1/4" spacer washer for bed | |||||
49 | 1 | steppers | 10-steppers | 1 | 1 | Control Panel | |||||
50 | BOX, BAG, AND INCLUDE OSE LINUX WITH LOVE. | 1 | 2 | Wire Loom Clip | |||||||
51 | 1 | Extruder Idler | 1 | 2 | Spool Holders | ||||||
52 | 5 | Belt Cylinder | 1 | 1 | Extruder Main | ||||||
53 | 5 | Belt Clamp | 1 | 1 | Exturder Secondary |