sympleSEQ_BOM
 Share
The version of the browser you are using is no longer supported. Please upgrade to a supported browser.Dismiss

 
View only
 
 
Still loading...
ABCDEFGHIJKLMNOPQRST
1
PartQuantityDesignator/s
2
[BASE MODEL] - included in full kit.
3
Logic BoardControl Board
4
ICs
5
CD40106 Hex Inverter1IC1
6
CD4017 Decade Counter1IC2
7
CD4011 Quad NAND Gate1IC3
8
TLC272 Dual Op-amp **1IC4
9
** You can also use TLV272, or pretty much any other TL-series dual linCMOS single supply op-amp with the same pinout.
10
** LM358 is also a drop in substitution!
11
12
NOTE: I highly recommend using IC sockets. You will need 2x14 pin, 1x16 pin and 1x8 pin DIP sockets if you are sourcing your own parts. The full kits include these sockets :)
13
14
Capacitors
15
.1uF Ceramic Capacitor (5mm spacing)4C1, C3, C6, C7
16
2.2uF Electrolytic Capacitor1C2
17
10uF Electrolytic Capacitor1C4
18
19
Diodes
20
5mm High Intensity LED, aka "ultra-bright"8LED1-8
21
1N914 Small Signal Diode21D1, D2, D3, D4, D5D1-8, D2.1-8
22
1N4148 or any other general purpose small signal diode should work just fine as well.
23
24
Resistors
25
Alpha 9mm PCB Mount 100k Potentiometer8CV1-8
26
Mouser Part Number: 317-2090F-100K
27
1M Linear Potentiomer (panel mount)1P1
28
100k Resistor4R1, R2, R7, R9
29
10k Resistor11R5, R6, R8R1-8
30
1k Resistor2R3, R4
31
5% should be fine for all resistors. You may wish to use 1% to increase temperature stability for the clock resistor (R5), but it's not absolutely crucial. If you have them around, you may as well use 1% for everything, but if you don't then don't worry about it!
32
33
Switches
34
PCB Mount super mini ON-OFF-ON Vertical Toggle Switch8S1-8
35
Futurlec Part Number: SPDT101PCSM
36
OR Mouser Part Number: 108-2AS3T1205-EVX
37
38
Hardware (NEW!)
39
M3 machine screws with nuts for securing to panels6
40
http://www.bigbluewave.co.uk/resynthesis/sympleseq_step_sequencer.htm
41
I recommend purchasing these ones from Ben at Re:Synthesis since he has some really nice ones, and you are buying a beautifully made panel from him anyway, right? ;)
42
12 pin female and male .1" (2.54mm) through-hole header6
43
Feel free to use a 40 pin header (these are most common) -- just break the other 28 pins off to make a 12 pin header! Make sure to get a male one AND female to connect the two PCBs together.
44
45
[PARTS YOU MUST GET] - NOT included in full kit!
46
47
Output Jacks (1/4", Banana, 1/8", etc.)2CV Out, GATE Out
48
SPDT Toggle Switch (only if building standalone!)1Power
49
9V Battery Clip (only if building standalone!)1GND, +V
50
51
[OPTIONAL PARTS] - NOT included in full kit!
52
53
Input Jacks (1/4", Banana, 1/8", etc.)3RESET In, PAUSE In, CLOCK In
54
SPDT Toggle Switch2RESET, PAUSE
55
.01uF Ceramic Capacitor (soldered across switch leads)2RESET, PAUSE
56
Knobs 6mm shaft/19mm max. diameter9CV1-8, P1
57
58
59
[DUAL EURORACK PARTS] - NOT included in full kit!
60
Here are some of the parts you might find handy if you're building a Re:Synthesis panel for your sympleSEQ:
61
Jacks12
62
NOTE: Mouser part number 16PJ138 are an excellent choice of jacks
63
SPDT Toggle Switch2RESET, PAUSE
64
.01uF Ceramic Capacitor (soldered across switch leads)4RESET, PAUSE
65
Momentary ON toggle switch2RESET, PAUSE
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Loading...
 
 
 
Sheet1