ABCDEFGHIJKLMN
1
2
Printer: F1 / F1+ / F2
3
4
Printer: F1 / F1+ / F2
5
6
Printer: F1 / F1+ / F2
7
8
Printer: F1 / F1+ / F2
9
10
Printer: F1 / F1+ / F2
11
ModeSettingZ-Axis OffsetLayer ThicknessSupport DensitySupport Point SizeDate and CommentsFirmwareResultAmbient Temp
12
Printer: F1 / F1+ / F2OpenClear V300.1mm10.6mm1/13/17 Raft did not stick to build plate, raft lightly cured to PDMS, Fairly bad smell even with no heat.0
13
OpenWhite V200.1mm10.7mm1/13/17 Raft just barely cured to build plate, most of it cured to PDMS layer, very funky smell - no heat.Fail
14
Printer: F1 / F1+ / F2OpenBlack V200.1mm 10.6mm1/13/17 Nice raft, good adhesion to build plate, crisp edges, a corner of the part did not cure to supports, hence the partial success. Maybe I will try increasing Support Point Size.Partial Success
15
OpenCastable V2480.1mm10.67mm1/13/17 Best print yet, crisp edges, fully printed including all supports. Edge near supports slightly distorted. Upon removal, raft was a weird undercured consistency, but it held. Everything else was fully cured. Probably best setting, just needs tweaking from here. Part has offense odor during post cure, final mechanical properties have slight flex, but do break under moderate stressSuccess
16
Printer: F1 / F1+ / F2OpenCastable V200.1mm0.80.7mm1/13/17 Tried a big print. Got greedy with my support density I guess. Raft cured to build plate, still a weird undercured, waxy consistency (maybe due to castable settings, maybe raft needs to be less cured in order to remove delicate parts or something), pretty much entire part cured in one big layer on the PDMS. Lots of little floaties, had to strain and reset.Fail
17
OpenCastable V200.1mm1.7mm1/14/17 Part was distorted, but I am starting to think it's just my part orientation and support layout. So far this setting, or the same setting with different support point size, is working the best.Success
18
Printer: F1 / F1+ / F2NA/Modified OpenClear V100.1mmNANA11/24/2017 Raft did not stick to build plate.
form1--0x140--telepathically-adeptness--15792357--2014-12-09--15-37-41
Fail74 F
19
NA/Modified OpenClear V200.1mmNANA
form1--0x140--telepathically-adeptness--15792357--2014-12-09--15-37-41
Fail74 F
20
Printer: F1 / F1+ / F2NA/Modified OpenCastable00.05mmNANA11/24/2017 Raft did not stick to build plate.
form1--0x140--telepathically-adeptness--15792357--2014-12-09--15-37-41
Fail74 F
21
NA/Modified OpenTough0
22
Printer: F1 / F1+ / F2NA/Modified OpenBlack V10
23
NA/Modified Open(Grey V200.1mm
form1--0x140--telepathically-adeptness--15792357--2014-12-09--15-37-41
74 F
24
Printer: F1 / F1+ / F2NA/Modified Open
25
NA/Modified Open
26
Printer: F1 / F1+ / F2NA/Modified Open
27
NA/Modified Open
28
29
Investment Casting
30
PrinterColorModeSettingZ-Axis OffsetLayer ThicknessSupport DensitySupport Point SizeDate and CommentsResult
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100