sympleSEQv2.0_EURORACK_BOM [PUBLIC]
 Share
The version of the browser you are using is no longer supported. Please upgrade to a supported browser.Dismiss

 
View only
 
 
Still loading...
ABCDEFGHIJKLMNOPQRST
1
sympleSEQ v2.0 DUAL EURORACK Bill of Materials
2
Part QtyDesignatorsNote/s
3
Logic BoardControl Board
4
5
Included in the full kits:
6
7
CD4017 Decade Counter 2IC1.1, IC1.2
8
CD4093 Quad NAND Gate2IC2.1, IC2.2
9
TLC274 Quad Operational Amplifier4IC3.1, IC3.2, IC4.1, IC4.2
10
Note: TLC279 is also a possible substitute. Pretty much any single supply quad opamp will work just fine!
11
12
LM78L05 Voltage Regulator4U2.1, U2.2, U3.1, U3.2T0-92 kinked lead package -- mouser part 512-LM78L05ACZXA
13
LM78L10 Voltage Regulator2U1.1, U1.2T0-92 kinked lead package -- mouser part 595-UA78L10ACLPRE3
14
15
14 pin DIP IC Socket6
16
16 pin DIP IC Socket2
17
18
.1uF Ceramic Disc Capacitor8C1.1, C1.2, C2.1, C2.2, C3.1, C3.2, C4.1, C4.25mm lead spacing
19
47uF Electrolytic Capacitor3C5.1, C6.1, C6.22.54mm lead spacing
20
.01uF Ceramic Disc Capacitor4C7.1, C7.2, C8.1, C8.25mm lead spacing
21
Note: All capacitors should be 25V rating or greater
22
23
1N914 Small Signal Diode54D1.1, D1.2, D2.1, D2.2, D3.1, D3.2, D4.1, D4.2, D5.1, D5.2, D6.1, D6.2, D7.1, D7.2, D8.1, D8.2, D9.1, D9.2, D10.2, D11.2, D12.1, D12.2All diodes on Control Board
24
Note: Or equivalent (ie: 1N4148)
25
26
1k Resistor12R1.1, R1.2, R2.1, R2.2, R3.1, R3.2, R4.1, R4.2, R5.1, R5.2, R6.1, R6.21/4W, 5% is fine for all resistors.
27
100k Resistor12R9.1, R9.2, R10.1, R10.2, R11.1, R11.2, R12.1, R12.2, R13.1, R13.2, R14.1, R14.21/4W, 5% is fine for all resistors.
28
10k Resistor20R15.1, R15.2, R16.1, R16.2All resistors on control board1/4W, 5% is fine for all resistors.
29
4.7k Resistor2R17.1, 17.21/4W, 5% is fine for all resistors.
30
100 Resistor2R18.1, 18.21/4W, 5% is fine for all resistors.
31
12k Resistor4R19.1, R19.2, R20.1, R20.21/4W, 5% is fine for all resistors.
32
15k Resistor2R21.1, R21.21/4W, 5% is fine for all resistors.
33
34
40 pin .1" male breakaway header3Jumpersbroken into 34 pins long (board-to-board), and 4 sections of 3 pins long (level jumpers)
35
40 pin .1" female header2Jumpersbroken into 34 pins long
36
2pin .1" jumper4Level JumpersLook on old computer hard drives/motherboards for these, if you can't find any around :)
37
38
5mm LED (ultra-bright)16All LEDs on Control BoardThe kits I supply contain red LEDs
39
LED Spacer16All LEDs on Control BoardMouser part number: 593-STD240B
40
41
ON-OFF-ON .1" pitch toggle switch16S1-8 (A/B)Mouser part number: 108-0044-EVX
42
Note: Alternatives: SPDT101PCSM (futurlec.com), EG2451-ND (Digikey)
43
44
Panasonic 5k (or 10, 20, 50, 100k) PCB mount linear taper potentiometer18CV1-8Mouser part number 667-EVU-F2MFL3B53 A lot of 9mm vertical pots will work (ie: Alps, Bourns, Alpha). CHECK THE DATASHEET IF YOU INTEND TO SUBSTITUTE!
45
D-shaft soft touch knob18Mouser part 450-4760
46
47
1/8" vertical mount jacks12All jacks on control boardErthenvar part number JACK35MMV or Mouser part number 16PJ138
48
49
SPDT toggle switch (PCB mount)3Run/Clock Select Switches Smallbear OR Mouser part number: 10TC410
50
Momentary ON push button switch (PCB mount))2Reset SwitchesMouser part number 611-D6R40F1LFS
51
52
2x5 .1" shrouded keyed header3Power XPAND_A, XPAND_BNOTE: XPAND ports are optional and are there for use by a future expansion module. You do not have to install them if you do not want to.
53
Eurorack 10pin Power Cable1Power
54
55
Re:Synthesis Dual Eurorack Panel1Panelhttp://www.resynthesis.co.uk
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Loading...
 
 
 
Sheet1