Make Page Steel Requirements


1	Step	StockSize	Size (Inches)	Length (Inches)	QTY.	Part Name

2	1	Flat	.25x2	12	1	Controller Mount
3	1	Flat	.25x3	6	1	Controller Mount, Bottom Piece
4	1	Flat	.25x6	12	1	Valve Mount
5	1	Flat	.25x6	15	1	Controller Mount
6	1	Sheet	.125x29x13.5		1	Dirt Keeper Plate
7	1	Sheet	.125x29x17.5		1	Brick Holder Plate
8	2	Angle	.5x4x6	72	2	Secondary Arms
9	2	Angle	.5x4x6	72	2	Primary Arms
10	2	Flat	.25x8	8	4	Feet
11	2	Tubing	.1875x2.5x2.5	6	14	Leg Holders
12	2	Tubing	.25x2x2	48	4	Legs
13	3	Angle	.25x2x2	10	2	Sides of guard
14	3	Angle	.25x2x2	16	2	Top and bottom of guard
15	3	Angle	.5x4x4	8	1	Motor mount angle
16	3	Angle	.5x4x4	21	1	Hopper Mount Angle
17	3	Rebar	1	7	2	Braces
18	3	Sheet	.125x10x16		1	Guard
19	4	Flat	1x2	5	1	Hammer
20	4	Flat	1x2	6	1	Hammer
21	4	Round	1	7.25	1	Shaft
22	6	Angle	.5x4x4	38	2	Grate supports
23	6	Tubing	.25x2x2		2	Hopper Supports
24	7	Flat	1/8x3	36	8	Hinge Plates
25	8	Flat	.5x3	11.25	2	Hopper Mounting Plate
26	8	Flat	.5x3	15	2	Hopper Mounting Plate
27	9	Angle	.25x2x2	35.5	2	Frame Short Pieces
28	9	Angle	.25x2x2	72	2	Frame Long Pieces
29	9	Flat	.25x2	71.5	1	Cross Support
30	9	Rebar	0.5	34	33	Rebars
31	10	Angle	.5x4x7	12	1	Back
32	10	Flat	.1875x2.5	36	2	Outer Rails
33	10	Flat	.25x7	13.5	2	Sides
34	10	Flat	.25x8	12.5	1	Roof
35	10	Flat	.5x2	36	2	Inner Rails
36	10	Flat	.5x3	3	1	Tongue
37	10	Flat	.5x6	12	1	Vertical Supports
38	10	Flat	1x7	12	1	Press Plate
39	10	Tubing	.5x6x6	12	1	Spacer
40	11	Flat	.375x 3	3	1	Spacer Plate
41	11	Flat	.5x3	3	1	Spacer Plate
42	11	Flat	.5x3	16	2	Main Plate
43	12	Angle	.25x2x2	6	2	Wide cylinder support Vertical
44	12	C-Channel	6 heavy	29	2	Wide cylinder support Horizontal
45	13	C-Channel	3	1.5	2	Thin Cylinder support
46	13	Flat	.25x1	14	1	Magnet Holder
47	13	Pipe	.75ID 1OD	1	2	Thin Cylinder support
48	13	Rebar	0.375	3	1	Sensor Holder
49	13	Rebar	0.375	6	1	Sensor Holder
50	13	Threaded Rod	0.75	1.25	1	Magnet Holder
51	13	Threaded Rod	0.75	3.5	1	Sensor Holder
52	13	Threaded Rod	0.75	3.5	1	Sensor Holder
53	13	Threaded Rod	0.75	6.25	2	Thin Cylinder support
54	14	C-Channel	6 heavy	21	4	Horizontal Members
55	14	C-Channel	6 heavy	53	2	Vertical Members
56	14	Threaded Rod	0.75	3.75	4	Drawer member drawer adjuster bolts
57	15	Flat	1x4	10	1	Lower Press Foot
58	15	Flat	1x6	12	1	Upper Press foot
59	15	Threaded Rod	0.75	2.5	2	Upper Press foot
60	16	DOM Round	1.5	3.5	1	Fill in rod tubing
61	16	Flat	1x1	2.5	2	Press foot supports
62	17	Tubing	6x12	50	1	Optional Jig
63	17	Angle	.25x2x2	6	2	Dirt Blockers
64	17	C-Channel	6 heavy	13	2	Spacers
65	17	Flat	.375x 3	24	2	Horizontal Members Reinforcement
66	18	DOM Round	1.5	11	1	Cylinder Pin
67	18	Dom tubing	1.5 ID 2.0OD	1.5	2	Horizontal Members, cylinder mounting
68	Assembly 5	Flat	.5x3	3	1	Eye for 2nd cyl