ABCDEFGHIJKLMNOPQRS
1
hexinverter.net Galilean Moons v1.02 Bill of Materials
2
Part QtyDesignatorsNote/s
3
4
Base Parts (all formats need these parts)
5
TL074 quad opamp3IC2, IC3, IC4
6
TL072 dual opamp4IC7, IC8, IC10, IC11
7
TLV2374 quad single supply rail-to-rail opamp1IC5Do NOT substitute for this part unless you ABSOLUTELY know what you are doing. Please do not email me asking for me to find substitutes for you either! Use THIS opamp! :)
8
LM13700 dual operational transconductance amplifier2IC6, IC9
9
PIC18F14K22 Microcontroller w/ firmware2UC1, UC2Included pre-programmed with PCBs/kits from hexinverter.net
10
MCP4821 12b DAC2DAC1, DAC2Mouser: 579-MCP4821-E/P
11
LM7805 5V voltage regulator1IC1
12
2N3904 NPN Transistor4 Q2, Q3, Q5, Q6
13
2N3906 PNP Transistor2Q1, Q4
14
The use of IC sockets for all integrated circuits is HIGHLY recommended
15
16
17
DIODES:
18
1N4148 small signal diode2D1, D21N914 or any other small signal diode should work fine as well
19
5mm LED (diffused white)2EG.LED1, EG.LED2 I recommend diffused LEDs. Mouser doesn't sell these in diffused. I get mine from eBay!
20
21
CAPACITORS (16V or greater rating):
22
1uF electrolytic capacitor1C135mm diameter, 2.5mm lead spacing
23
220uF electrolytic capacitor3C1, C4, C66.3mm diameter, 2.5mm lead spacing
24
100pF4C9, C10, C17, C18 5mm lead spacing
25
330pF2 C11, C19 5mm lead spacing
26
6.8nF 2C24, C25 5mm lead spacing
27
12nF4 C20, C22, C26, C275mm lead spacing
28
18nF2C21, C235mm lead spacing
29
0.1uF10C3, C5, C8, C12, C14, C15, C2, C7, C28, C29 5mm lead spacing
30
31
RESISTORS (1/4W, metal film):
32
100R4R22, R42, R50, R57
33
1k10R1, R4, R12, R18, R38, R76, R34, R46, R53, R66
34
4.7k2R69, R70
35
6.8k8R58, R59, R60, R61, R62, R63, R64, R65
36
10k26 R2, R5, R7, R8, R9, R10, R11, R13, R14, R19, R23, R25, R27, R28, R29, R31, R33, R35, R36, R44, R40, R41, R67, R68, R71, R72
37
33k6R17, R26, R32, R48, R52, R55
38
47k2 R30, R54
39
100k16R3, R6, R16, R21, R39, R43, R45, R75, R15, R20, R24, R47, R49, R51, R73, R74
40
1M2R37, R56
41
42
100k cermet 12 turn trim pot (straight lead pattern)4T1, T2, TLED1, TLED2Mouser: 858-67WR100KLF
43
44
HARDWARE/ETC:
45
M3 machine screws (M3x35mm)4For connecting the boards together (not in Mouser cart)
46
12mm PCB spacers8For connecting the boards together (not in Mouser cart)
47
48
40pin male .1" breakaway header4For connecting the PCBs together -- broken into appropriate sections
49
40pin female .1" breakaway header2NOTE: headers are not in Mouser cart. Find these somewhere else! For example: http://dipmicro.ca
50
51
PCB set w/ microcontrollers1N/Ahttp://www.hexinverter.net
52
53
Eurorack Specific Control Board Parts (included in full eurorack kits)
54
55
Vertical PCB Mount 10kB potentiometers6ENV1.ATK, ENV1.DK, ENV2.ATK, ENV2.DK, BIAS1, BIAS2Alpha pots: http://www.taydaelectronics.com/10k-ohm-linear-taper-potentiometer-round-shaft-pcb-9mm.html [THESE ARE ROUND SHAFT AND NEED KNOBS WITH SET SCREWS]
56
Other pots: BI Tech. P0915N-FC15BR10K [THESE ONES ARE D-SHAFT AND ARE THE SAME AS IN THE KITS]
57
D-shaft knobs if using BI pots, else, set screw (for Alpha)6Mouser part 450-4760
58
PCB Mount ON-OFF-ON sub-mini toggle switch2SW.MODE1, SW.MODE2Mouser: 108-0044-EVX
59
PCB Mount ON-ON sub-mini toggle switch2SW.SHAPE1, SW.SHAPE2Mouser: 108-0042-EVX
60
3.5mm vertical mount jacks15All jacksKobiconn Jacks: Mouser part number 16PJ138
61
62
Eurorack power cable1http://erthenvar.com/store/eurodiy/power/cable1016
63
Eurorack power connector (or 2x5 .1" male header)2Power, XPANDNOTE: not in Mouser cart. Find these somewhere else! For example: http://dipmicro.ca
64
65
10pin .1" female STACKABLE header4http://www.taydaelectronics.com/stackable-header-10-pins-2-54mm.html
66
8pin .1" female STACKABLE header4http://www.taydaelectronics.com/stackable-header-8-pins-2-54mm.html
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100