�Phenom XXL and XXL V2 Chitu Version Quickstart Guide
Revision 1.02�Published December 01, 2023
Step 1
Remove Packaging
Phenom XXL is heavy and it is recommended that you have at least four more person to help.
Please place the wooden box as shown below�
Step 1
Remove Packaging
Take out the latches of the 6 box buckles on the wooden box and open the buckles to remove the top panel
�
Straighten the 22 hook pieces as shown in the figure below with a tool to remove the four-sided panel
Step 1
Remove Packaging
This is after the printer opened the wooden box�
When moving the Phenom XXL, it is recommended for a 2 person lift. If you try and move it by yourself, please make sure the door is facing away from you as the UV acrylic shield could break with the weight if it the door is pressed against your chest while moving the printer. �
Step 2
Find a place for
Phenom XXL
�Place the Phenom XXL on a level and sturdy surface. If you have a level, you can place it on the top of the printer to ensure the printer is sitting level. �
�Keep in mind that the printer is large, (78 X 57.1 X 112cm / 30.7 x 22.5 x 44.1 inches) and is heavy (115kg / 253.5 pounds). Please make sure the area you put the printer on can support the weight and provide enough space for proper ventilation for the printer. ��Also consider that you will need a washing and curing station near the printer when planning out your set up.
Step 3
Open The front door of Phenom XXL and remove the foam inserts in the printer. There are accessories in the foam protectors.
The items from top to bottom are:
LCD Panel (if purchased additionally)�Accessories�Build Plate�Vat
Step 4
Identify the following items and place them off to the side:�1).Build Plate�2).Vat�3).Extra FEP film�4).Tools�5). USB stick�6). Funnels�7). Power cable
8). Spatula
9). Extra XXL V2 screen
10). Shading tape
���
Step 5
Make sure the power cord is a 3 prong / grounded power cord. ��Connect the power pack to the Phenom XXL and to a outlet
Step 6
�Power on the Phenom XXL and boot up the printer. ��You should see the Peopoly logo and then the main control screen.
Step 7
From the touch screen, raise the build plate up high enough so the vat can be inserted.��This can be done by pressing the wrench (tool) (1).��Then manual (2).��Select the amount of movement in milimeters you want to use. ��Then the up arrow.�
Step 8
Clean the LCD panel inside Phenom XXL with some isopropyl alcohol (IPA) at least 90 to 99% pure to make sure the surface is clean.��It is recommended not to use glass cleaner as it could leave a residue on the screen that could affect print quality.��Another recommendation, is to use a lint free microfiber cloth, soft cloth or soft paper towel so the LCD screen does not get scratched. ���
Step 9
Check to ensure the build plate is level to the LCD screen.
�It is very important to make sure the build plate and LCD screen is clean of any debris for this next step. . ��1). Ensure that the build plate is secure to the Z axis arm.�����
2). Get either a blank sheet of paper, or notebook paper.
3). Turn on the printer and go into Tools, Manual control, and then home.
��
This will bring the build plate down to the LCD panel and we will check to make sure that it is level to the LCD plate.
�4). Take the paper and try and slide it under where the plate meets the LCD panel all around. It should be that the paper should not slide under the build plate.��
Step 9 (continued)
If it still does, then on the display screen, make sure 0.1 is highlighted, this is the distance the Z axis will move, press the down arrow and hte plate will descend. Check the gap again, if there is still a gap, then repeat the process of lowering the Z axis and checking till the paper can not slide under the plate. You can keep moving down up to 0.6mm
��Once the plate is level to the screen, press the back button and then press the button that says Set Z=0 This will store the new height as the default Z axis as 0 with the new height.
If the paper slides under the plate, then loosen up the 4 bolts on top of the build plate so that plate should descend slightly.
Recheck again to make sure the paper does not slide under the plate. GENTLY press down the plate to make sure it is level to the LCD and carefully re-tighten the bolts, again double checking to make sure the paper does not slide between the plate and LCD.
Step 10
Make sure the Vat FEP sheet (film) is clean on both sides. Use the same cleaning method mentioned in the previous step if need be.
Step 11
Wait until alcohol in step 8 and 9 is evaporated before installing the vat. ��Carefully slide the vat into place so that it rests against the vat holder on each side(please be careful not to scratch your hands or scratch the film).��Turn four screws on both sides so the vat is secured. Please note. It is not needed to overtighten the bolts, they should be finger tight.
Step 12
With the Z axis raised all the way to the top. Take the build plate and with some IPA, clean the underside of the build plate. ��Slide it onto the support arm and tighten down the build plate knob to secure it in place. ��The build plate has been leveled at the factory and should not need to be adjusted. If by chance it has become loose via shipping, please refer to the main guide on how to level the build plate.
Step 13
Download Test Print File at the following location �� https://drive.google.com/file/d/1jixl28UxrZKUhIaSG4voJtOJzZdXRZcB/view?usp=sharing
�Save / copy over the file to the included USB drive and insert to the printer
�Note: There is a print test document in the usb disk, which is based on the Deft resin print test. If you change to another resin print test, please adjust the print parameters. The small square is a difficult model to print.
Step 14
Glove up! Make sure that the cover of the resin container is on tight and shake it up for about 15 - 30 seconds vigorously.
Open the bottle and pour it into the VAT, you can go a small bit past the angle line in the tank. ��DO NOT OVERFILL THE TANK! If so, when the plate descends, resin will overflow. ��For Peopoly resin, we recommend Deft and Neo. The only 3rd party resin we recommend outside of the Peopoly brand is Siraya Tech's Fast and Simple. We have many users running that exclusively too.
�** For new resin bottles, after opening the first time, remove the retention ring on the bottle so it does not fall into the vat.
Step 15
With the test file copied over to the USB stick, insert it into the side of the printer. On the main control window, press print, then select the demo file, and print. �����������With the printer starting, let's get the software setup.
Down and Install Chitubox Slicer Software
Step 16
You can download Chitubox 1.9.5 or the latest stable version here if you do not already have it
https://www.chitubox.com/en/download/previous/chitubox-free
��
Download and install Chitubox as this is the default slicing program for the Phenom XXL.
Adding Phenom XXL Printer in Chitubox
Be sure to use XXL settings for printing AND supports
Step 17-1
1.Click Setting in Chitubox on the right side of screen
2. Add new printer by press + on the upper left corner
�
�3. Select Peopoly Phenom XXL from the list
����
�
Making Sure Phenom XXL profile is correct�������
Step 17-2
1 You will find 2 profiles for Deft and Neo�
�
�2. Double check machine setting matches to below�
�
�
Making Sure Phenom XXL profile is correct
Please change the rest time to 3S
Step 17-3
1 Deft 50um
2 Neo 50um
1、Configure Chitubox Support
Step 18
2、Download support config parameters ��https://drive.google.com/file/d/1JqoHdm0D-LxWvvloJQK7hN-GFn2a4PtY/view?usp=sharing����
����
1) Select Support Setting icon in the upper right corner of the Chitubox
2) Import support configuration parameters
Check for firmware updates
Step 19
You can find out the firmware version on your Phenom XXL by using information under system menu
��
And check your firmware version.
The latest is 2.11.
Resin and Printing Considerations
Step 20-1
For Peopoly resin, we recommend Deft and Neo. The only 3rd party resin we recommend outside of Peopoly brand is Siraya Tech's Fast(Grey/White/Green/Smoky Black/Creamy/Metal Grey) and Simple(Clear/Grey/Smoky Black).
Here is a guide on resins, including use of 3rd party resins:
https://docs.google.com/document/d/1OKDZjyL88wFwuydggg9x2BJYXW3rZVjBd365wsubzH0/edit?usp=share_link
Make sure the build is clean and there is no cured residue in the VAT before the next print. Crushed prints will damage the panel with a bullet-like impact.
For hollow 3D models, Wall thickness >3mm
The best printing temperature of resin is 25-30℃
Resin and Printing Considerations
Step 20-2
For the Chitu mainboard, when you manually stop printing during the printing process, the motor cannot lock automatically and the platform will slide downward. At this time, click "Tools-Manual-Up Arrow" on the touchscreen(see the picture below) or turn off the machine to lock the motor
Step Finito
You are all set!�Your Phenom XXL should be printing the test file, and you have Chitubox installed on your computer now. ��If you need further assistance, please refer to the full guide here.��Or reach out to us via our facebook page or forums.�https://www.facebook.com/peopoly/�https://forum.peopoly.net/���Join our Phenom official facebook page �https://www.facebook.com/groups/2240866646207938/?ref=br_rs��And share your prints on social media with the hashtag #Phenom��