1 of 23

Polybuilt

California Polytechnic University San Luis Obispo 1

A - Team Design Report 2021

_________________________ __________________________

​

Dante P. , Team Captain Dr. Mohammad Sadek, Advisor

2 of 23

Table of Contents

Design Objectives

​

Design Specifications

Operator’s Station Design

Polybuilt Organizational Design

Strategy

Structure

Processes

People

Drivetrain Design

​

Steering and Electrical systems design

​

Brake design evolution

​

Clutch Hydraulic Throwout Cylinder Evolution and Re-Design

​

Manufacturing

Serviceability and Safety

Tractor Cost Overview

Cost Analysis

Qualitative Risk Analysis

Acknowledgments and Citations

FMEA - Electric Kill Switch

​

​

​

​

​

4

​

5

6

7

8

9

10

11

12

​

13

​

14

​

15

​

16

17

18

19

20-21

22

23

​

​

​

​

​

California Polytechnic University San Luis Obispo 1

3 of 23

List of Figures

Figure 1. Polybuilt Tractor

Figure 2. Organizational Structure

Figure 3. Labeled Tool Wall

Figure 4. Drivetrain

Figure 5. Disk Brakes

Figure 6. Hydraulic Throwout Cylinder

California Polytechnic University San Luis Obispo 1

6

9

10

12

14

15

​

4 of 23

Design Objectives

Design Objectives

Matching Features

California Polytechnic University San Luis Obispo 1

    • Aluminum in previous models was replaced with steel

Durability  

    • Theory of Constraints applied to Polybuilt’s production system

Production Efficiency 

    • Adequate space to access and service drivetrain components

Easy Maintenance  

    • Designed with space for adding implements

Potential for Various Uses  

    • Greater steering radius and new steering brakes

Maneuverability   

5 of 23

Design Specifications

California Polytechnic University San Luis Obispo 2

Engine

    • Briggs & Stratton 31hp Vanguard V-twin

Transaxle

    • Midwest Super Cub 3 Forward & 1 Reverse Gear

Steering

    • Hydraulic Steering 2.75 Turns Lock to Lock

Capacities

    • Fuel Tank - 5.5 Quarts
    • Engine Oil - 2.3L w/ Filter
    • Hydraulic Oil - .5 Quart

Dimensions

    • 72” Wheel Base
    • 95” OAL
    • 42” Max Width
    • COG 23” Forward of Rear Axle

6 of 23

Operator’s Station Design

California Polytechnic University San Luis Obispo 3

Features

Benefits

Steel framing steering column instead of the previous Aluminum column

More stiff steering column

Shorter frame compared to prior design

Closer proximity to the steering wheel to make it more accessible

Ergonomic seat

More comfort for the operator

Figure 1. 2021 Polybuilt Tractor

7 of 23

Polybuilt Organizational Design

California Polytechnic University San Luis Obispo 4

Strategy

    • Competitive advantage
    • Products and services

Structure

    • Level of specialization
    • Centralization vs. Decentralization

Processes

    • Workflows
    • Budget allocation

People

    • Hybrid organizational structure

Polybuilt applied several elements of the Star Model to design the organization

Galbraith, J. (n.d.). Designing your organization: The Star Model. John Wiley & Sons.

​

8 of 23

Strategy

What Polybuilt offers to our clientele

​

1. Design and cost control

Parts designed and built in-house to maintain greater design and cost flexibility

2. Excellent services to keep equipment functioning and reliable when it is needed most

Aftermarket repair and maintenance options and plans

​

Polybuilt’s competitive advantage

​

Custom built tractors that align with the specific needs of our client’s operation

California Polytechnic University San Luis Obispo 5

9 of 23

Structure

Polybuilt was developed as a relatively decentralized organization because the company is small and takes advantage of the fluidity of the horizontally oriented transfer of communications and decision making. Horizontally designed firms also benefit from the speed at which they can respond to demand fluctuations, evolving customer needs, and other market changes.

As shown in the figure, Polybuilt has 3 departments: design, construction, and business. The company’s founders determined that this structure represented the optimal level of specialization to keep the firm functioning effectively. The horizontal arrows in the figure represent the subsystems of the tractor and the project teams tasks with developing each. The joints are there to visually convey the matrix structure and show how it aligns projects with professionals from all departments to maximize the benefits to be gained from cross-functional teams.

​

Figure 2. Organizational Structure

California Polytechnic University San Luis Obispo 6

10 of 23

Processes

Polybuilt uses standard practices and procedures for budget allocation, but continuously changing workflow processes with the following objectives in mind:

1. Improving efficiency by selecting the optimal combination of material, design, and manufacturing process

2. Reducing the wastes identified in the lean model by identifying them and developing workflows for future operations that eliminate them

​

3. Conducting value-added analyses on our workflows to ensure that all steps in an operation are necessary and produce valuable features for the end user

4. Keeping organized and accessible workstations by having designated locations for all tools with clear labels, as shown in the figure to the side, to avoid misplacement of tools or time spent obtaining the tools required for an operation

​

Figure 3. Labeled Tool Wall

California Polytechnic University San Luis Obispo 7

11 of 23

People

Polybuilt’s model for training and development is represented in the figure on the side. The concept is to not only promote specialization in one of the 3 departments at Polybuilt, but to also give teams an opportunity to think holistically.

For example, the design expert on a team may have a conceptual design for a major drivetrain component that they discuss with the construction expert and the business specialist. The representative from the construction department may then state that the design is unnecessarily complex and that simplifying it will cut fabrication time by 10% without having to eliminate any required features of the component. The business expert may then enter the discussion and propose some methods of reducing direct labor or material cost.

Recruitment

Develop department related skills

Gain familiarity with the operations of the other department

Work as a member of a cross functional team on a specific custom tractor

Solve problems and track job progress as each tractor is being designed and constructed

California Polytechnic University San Luis Obispo 8

12 of 23

Drivetrain Design

California Polytechnic University San Luis Obispo 9

The differential in the transaxle was flipped which allowed Polybuilt to eliminate the 1 to 1 gearbox that was previously being used to change the direction of rotation on the incoming shaft. Not only did this gearbox represent an extra cost especially because of the CNC machining required to produce it, but it also increased the weight of the vehicle. Eliminating the gearbox saved PolyBuilt both money and weight.

Figure 4. Drivetrain

13 of 23

Steering System Design

A hydraulic system was chosen over a rack and pinion design because it would be easier for the operator to repair and replace parts. An electrical steering system was another option, but was decided against because an electrical power loss would leave the operator with no means of controlling their steering. Such a scenario could be dangerous for the operator, so a system that could function without power was selected.

California Polytechnic University San Luis Obispo 10

Electrical System Design

The electrical system of the tractor includes a ground speed sensor, a gear position sensor, and an engine speed sensor.

14 of 23

Brake Design Evolution

Brake Design Version I

​

The internal brake built into the transaxle was originally going to be used to halt the tractor. To test the brake, a six foot moment arm was attached to the axle shafts and it was concluded that the brake could only handle 503 Lb-ft on average. From the technical inspection requirements, it was determined that 805 Lb-ft of force is required to support the tractor on a 20 degree incline.

​

Disk brakes were incorporated into the design, one on each rear wheel, as a substitute for the internal brake. Each brake is controlled by a separate pedal for independent braking and better maneuverability.

California Polytechnic University San Luis Obispo 11

Figure 5. Disk Brakes

15 of 23

Clutch Hydraulic Throwout Cylinder Evolution and Re-Design

Since the development of the PolyBuilt TorqMaster clutch-pack, PolyBuilt has experienced frequent issues with the hydraulic throwout cylinder on their clutch-pack. The first cylinder used was a pre-manufactured part (a new one shown in Figure 6 in the rear center) which kept failing from over pressurization, extruding the o-ring. The wall thicknesses across this cylinder were considerably thin, and it also suffered from some mechanical damage over a short time. Two years ago, engineers at PolyBuilt designed a replacement for this throwout cylinder. The new cylinder (shown on the left in the figure) was structurally stronger and utilized two back-up anti-extrusion rings for each o-ring groove. The internal grooves were fairly difficult to properly manufacture, but the new cylinder seemed to operate well. When testing the new cylinder for a couple of hours, it developed a large leak and failed to maintain pressure. The cause was determined to be a sharp burr cutting into the o-ring in the groove that went undetected.

​

The engineers at PolyBuilt decided that the internal grooves posed a severe threat to quality assurance and designed their latest throwout cylinder with external grooves (shown on the right of the figure). The new hydraulic throwout cylinder was much easier to manufacture and has performed well for multiple tests without issue.

​

California Polytechnic University San Luis Obispo 12

Figure 6. Hydraulic Throwout Cylinders

16 of 23

Manufacturing

Aluminum was chosen instead of steel to manufacture the tractor’s steering column, front axle, and parallel shaft gearbox. This decision saved labor hours and decreased wear on the attachments for the CNC machine.

​

The CNC machine was used to decrease labor hours to machine parts and to ensure that they are manufactured precisely because the machine is programmed to cut the material to the exact dimensions inputted. Another benefit of using the CNC is that once it is programmed to perform an operation, the machine can repeat the process numerous times which would accelerate production if the tractor were to be manufactured on a large scale.

California Polytechnic University San Luis Obispo 13

17 of 23

Serviceability

Safety

The spaciousness of the tractor’s overall design allows for easy access to drivetrain elements so they can be serviced without obstacles or the need to remove and disassemble large components to reach these components.

The heat shielding surrounding the exhaust pipe has been improved in comparison to the previous models of Polybuilt’s tractors. Another feature Polybuilt added to improve operator safety is pressure switches on the brakes that ensure the engine will not start until the brake is applied. One other item newly added to the tractor is a gear position sensor that will prevent the engine from starting unless the vehicle is in neutral. Finally, there is one breakaway switch and 1 kill switch that will shut down the engine when the operator is not present in the seat.

California Polytechnic University San Luis Obispo 14

18 of 23

Tractor Cost Overview

California Polytechnic University San Luis Obispo 15

* = shown as a percentage of total manufacturing cost

Profit margin

20%

Total Manufacturing Cost / Unit

$13,546.17

Manufacturing Variable Cost

$11,779.28

*Indirect Manufacturing Cost

10%

*Research and Development Cost

5%

Suggested sales price

$16,255.00

19 of 23

Cost Analysis

Cost Strategy: Applied the Theory of Constraints

  1. Identify the bottleneck machine or step in the workflow of each major tractor subsystem
  2. The bottleneck is the machine or operation in the workflow with the slowest output rate
  3. Increase the flow, or rate, of parts through this bottleneck machine
  4. This was done by keeping the bottleneck active on all workdays
  5. Add reserve capacity to the operations and corresponding machines upstream of the bottleneck
  6. This ensures that the bottleneck will always have extra work in progress ahead of it so it will stay busy at all times

​

California Polytechnic University San Luis Obispo 16

Future cost reduction steps

When Polybuilt expands its operation to reach growing demand pools, costs will be reduced naturally through economies of scale. The fixed costs of operation will certainly rise as new manufacturing plants become active, but overall variable costs across all branches of the firm will decrease since more orders will be placed and more units will be sold.

20 of 23

Qualitative Risk Analysis

California Polytechnic University San Luis Obispo 17

Impact Level

Risk Type

Level 1

Level 2

Level 3

Quality

Minor problems with the paint and exterior finishes

The frame, armrests, or steering wheel location make the tractor less ergonomic

Drivetrain problems that cause the vehicle to be inoperable or unsafe

Procurement

The cost of steel or aluminum material rises 1-2%

A single source vendor can no longer provide a part Polybuilt outsources

A sole source vendors that provides a key drivetrain component goes out of business

​

Market

A time-phase financial analysis reveals that sales dropped less than 2%

Sales decrease more than 5% in less than 1 year

A recession pushes down demand for tractors because farmers can no longer justify the large investment with lower forecasted revenues

​

​

Q1

Q2

Q3

P1

P2

P3

M3

M2

M1

21 of 23

Qualitative Risk Analysis

California Polytechnic University San Luis Obispo 18

Risk ID (from previous slide)

Risk Prevention Plan

M1

Polybuilt will continuously improve its products to offer more value to our customers and more reason to purchase our vehicles

M2

Polybuilt will encourage its distributors to use sale pricing, enhanced marketing and visibility techniques, and other means of boosting sales

M3

Polybuilt will help farmers during economic downturns by offering payment plans and other flexible purchase options

P1

Polybuilt will be prepared in advance to secure material from one or two other alternative sources

P2

Polybuilt will compare other vendors based on pre-established criterion and select a different source for parts that must be outsourced

P3

Polybuilt will plan a means of manufacturing all parts of the tractor so, if need be, the firm can operate without being dependent on any sole source vendors

Q1

The risk will be accepted because its low impact severity and low probability combined result in it being a low priority risk

Q2

User experience will be tested with every major design change that impacts the ergonomic rating of Polybuilt’s tractors

Q3

Quality testing and inspection will be conducted on a regular basis at every Polybuilt manufacturing plant

22 of 23

Acknowledgments and Citations

Polybuilt would like to acknowledge all of the following sponsors for the resources they provided to make this year’s participation in the competition possible:

California Polytechnic University San Luis Obispo 19

23 of 23

FMEA – Electric Kill Switch

California Polytechnic University San Luis Obispo 20