SWITCHING�

​

​

BRANCH-E&TC ENGINEERING

SEM – 4^th

SUBJECT-DATA COMMUNICATION AND COMPUTER NETWORK

CHAPTER-05- switching & routing

TOPIC- switching

Ay-2021-2022 ,summer-2022

FACULTY-ER V BEHERA.(LECTURER E & Tc engg dept)

Switching Networks

• Long distance transmission is typically done over a network of switched nodes
• Nodes not concerned with content of data
• End devices are stations
• Computer, terminal, phone, etc.
• A collection of nodes and connections is a communications network
• Data routed by being switched from node to node

Nodes

• Nodes may connect to other nodes only, or to stations and other nodes
• Node to node links usually multiplexed
• Network is usually partially connected
• Some redundant connections are desirable for reliability
• Two different switching technologies
• Circuit switching
• Packet switching

​

Simple Switched Network

Circuit Switching

• Dedicated communication path between two stations
• Three phases
• Establish
• Transfer
• Disconnect
• Must have switching capacity and channel capacity to establish connection
• Must have intelligence to work out routing

Circuit Switching - Applications

• Inefficient
• Channel capacity dedicated for duration of connection
• If no data, capacity wasted
• Set up (connection) takes time
• Once connected, transfer is transparent
• Developed for voice traffic (phone)

​

​

Public Circuit Switched Network

Telecomms Components

• Subscriber
• Devices attached to network
• Subscriber line
• Local Loop
• Subscriber loop
• Connection to network
• Few km up to few tens of km
• Exchange
• Switching centers
• End office - supports subscribers
• Trunks
• Branches between exchanges
• Multiplexed

Circuit Establishment

Circuit Switch Elements

Circuit Switching Concepts

• Digital Switch
• Provide transparent signal path between devices
• Network Interface
• Control Unit
• Establish connections
• Generally on demand
• Handle and acknowledge requests
• Determine if destination is free
• construct path
• Maintain connection
• Disconnect

Blocking or Non-blocking

• Blocking
• A network is unable to connect stations because all paths are in use
• A blocking network allows this
• Used on voice systems
• Short duration calls
• Non-blocking
• Permits all stations to connect (in pairs) at once
• Used for some data connections

​

Space Division Switching

• Developed for analog environment
• Separate physical paths
• Crossbar switch
• Number of crosspoints grows as square of number of stations
• Loss of crosspoint prevents connection
• Inefficient use of crosspoints
• All stations connected, only a few crosspoints in use
• Non-blocking

Space Division Switch

Multistage Switch

• Reduced number of crosspoints
• More than one path through network
• Increased reliability
• More complex control
• May be blocking

Three Stage Space Division Switch

Time Division Switching

• Modern digital systems rely on intelligent control of space and time division elements
• Use digital time division techniques to set up and maintain virtual circuits
• Partition low speed bit stream into pieces that share higher speed stream

Control Signaling Functions

• Audible communication with subscriber
• Transmission of dialed number
• Call can not be completed indication
• Call ended indication
• Signal to ring phone
• Billing info
• Equipment and trunk status info
• Diagnostic info
• Control of specialist equipment

​

Control Signal Sequence

• Both phones on hook
• Subscriber lifts receiver (off hook)
• End office switch signaled
• Switch responds with dial tone
• Caller dials number
• If target not busy, send ringer signal to target subscriber
• Feedback to caller
• Ringing tone, engaged tone, unobtainable
• Target accepts call by lifting receiver
• Switch terminates ringing signal and ringing tone
• Switch establishes connection
• Connection release when Source subscriber hangs up

​

​

Switch to Switch Signaling

• Subscribers connected to different switches
• Originating switch seizes interswitch trunk
• Send off hook signal on trunk, requesting digit register at target switch (for address)
• Terminating switch sends off hook followed by on hook (wink) to show register ready
• Originating switch sends address

Location of Signaling

• Subscriber to network
• Depends on subscriber device and switch
• Within network
• Management of subscriber calls and network
• ore complex

​

In Channel Signaling

• Use same channel for signaling and call
• Requires no additional transmission facilities
• Inband
• Uses same frequencies as voice signal
• Can go anywhere a voice signal can
• Impossible to set up a call on a faulty speech path
• Out of band
• Voice signals do not use full 4kHz bandwidth
• Narrow signal band within 4kHz used for control
• Can be sent whether or not voice signals are present
• Need extra electronics
• Slower signal rate (narrow bandwidth)

Drawbacks of In Channel Signaling

• Limited transfer rate
• Delay between entering address (dialing) and connection
• Overcome by use of common channel signaling

​

Common Channel Signaling

• Control signals carried over paths independent of voice channel
• One control signal channel can carry signals for a number of subscriber channels
• Common control channel for these subscriber lines
• Associated Mode
• Common channel closely tracks interswitch trunks
• Disassociated Mode
• Additional nodes (signal transfer points)
• Effectively two separate networks

Common v. In Channel Signaling

Common�Channel�Signaling �Modes

Signaling System Number 7

• SS7
• Common channel signaling scheme
• ISDN
• Optimized for 64k digital channel network
• Call control, remote control, management and maintenance
• Reliable means of transfer of info in sequence
• Will operate over analog and below 64k
• Point to point terrestrial and satellite links

SS7 �Signaling Network Elements

• Signaling point (SP)
• Any point in the network capable of handling SS7 control message
• Signal transfer point (STP)
• A signaling point capable of routing control messages
• Control plane
• Responsible for establishing and managing connections
• Information plane
• Once a connection is set up, info is transferred in the information plane

Transfer �Points

Signaling Network Structures

• STP capacities
• Number of signaling links that can be handled
• Message transfer time
• Throughput capacity
• Network performance
• Number of SPs
• Signaling delays
• Availability and reliability
• Ability of network to provide services in the face of STP failures

​

Softswitch Architecture

• General purpose computer running software to make it a smart phone switch
• Lower costs
• Greater functionality
• Packetizing of digitized voice data
• Allowing voice over IP
• Most complex part of telephone network switch is software controlling call process
• Call routing
• Call processing logic
• Typically running on proprietary processor
• Separate call processing from hardware function of switch
• Physical switching done by media gateway
• Call processing done by media gateway controller

​

Traditional Circuit Switching

Softswitch

Packet Switching Principles

• Circuit switching designed for voice
• Resources dedicated to a particular call
• Much of the time a data connection is idle
• Data rate is fixed
• Both ends must operate at the same rate

​

Basic Operation

• Data transmitted in small packets
• Typically 1000 octets
• Longer messages split into series of packets
• Each packet contains a portion of user data plus some control info
• Control info
• Routing (addressing) info
• Packets are received, stored briefly (buffered) and past on to the next node
• Store and forward

​

Use of Packets

Advantages

• Line efficiency
• Single node to node link can be shared by many packets over time
• Packets queued and transmitted as fast as possible
• Data rate conversion
• Each station connects to the local node at its own speed
• Nodes buffer data if required to equalize rates
• Packets are accepted even when network is busy
• Delivery may slow down
• Priorities can be used

Switching Technique

• Station breaks long message into packets
• Packets sent one at a time to the network
• Packets handled in two ways
• Datagram
• Virtual circuit

​

Datagram

• Each packet treated independently
• Packets can take any practical route
• Packets may arrive out of order
• Packets may go missing
• Up to receiver to re-order packets and recover from missing packets

​

Datagram�Diagram

Virtual Circuit

• Preplanned route established before any packets sent
• Call request and call accept packets establish connection (handshake)
• Each packet contains a virtual circuit identifier instead of destination address
• No routing decisions required for each packet
• Clear request to drop circuit
• Not a dedicated path

​

Virtual�Circuit�Diagram

Virtual Circuits v Datagram

• Virtual circuits
• Network can provide sequencing and error control
• Packets are forwarded more quickly
• No routing decisions to make
• Less reliable
• Loss of a node looses all circuits through that node
• Datagram
• No call setup phase
• Better if few packets
• More flexible
• Routing can be used to avoid congested parts of the network

​

Packet Size

Circuit v Packet Switching

• Performance
• Propagation delay
• Transmission time
• Node delay

​

Event Timing

X.25

• 1976
• Interface between host and packet switched network
• Almost universal on packet switched networks and packet switching in ISDN
• Defines three layers
• Physical
• Link
• Packet

X.25 - Physical

• Interface between attached station and link to node
• Data terminal equipment DTE (user equipment)
• Data circuit terminating equipment DCE (node)
• Uses physical layer specification X.21
• Reliable transfer across physical link
• Sequence of frames

​

X.25 - Link

• Link Access Protocol Balanced (LAPB)
• Subset of HDLC
• see chapter 7

​

X.25 - Packet

• External virtual circuits
• Logical connections (virtual circuits) between subscribers

​

X.25 Use of Virtual Circuits

Virtual Circuit Service

• Logical connection between two stations
• External virtual circuit
• Specific preplanned route through network
• Internal virtual circuit
• Typically one to one relationship between external and internal virtual circuits
• Can employ X.25 with datagram style network
• External virtual circuits require logical channel
• All data considered part of stream

X.25 Levels

• User data passes to X.25 level 3
• X.25 appends control information
• Header
• Identifies virtual circuit
• Provides sequence numbers for flow and error control
• X.25 packet passed down to LAPB entity
• LAPB appends further control information

User Data and X.25 Protocol Control Information

Frame Relay

• Designed to be more efficient than X.25
• Developed before ATM
• Larger installed base than ATM
• ATM now of more interest on high speed networks

​

Frame Relay Background - X.25

• Call control packets, in band signaling
• Multiplexing of virtual circuits at layer 3
• Layer 2 and 3 include flow and error control
• Considerable overhead
• Not appropriate for modern digital systems with high reliability

​

Frame Relay - Differences

• Call control carried in separate logical connection
• Multiplexing and switching at layer 2
• Eliminates one layer of processing
• No hop by hop error or flow control
• End to end flow and error control (if used) are done by higher layer
• Single user data frame sent from source to destination and ACK (from higher layer) sent back

Advantages and Disadvantages

• Lost link by link error and flow control
• Increased reliability makes this less of a problem
• Streamlined communications process
• Lower delay
• Higher throughput
• ITU-T recommend frame relay above 2Mbps

Protocol Architecture

Control Plane

• Between subscriber and network
• Separate logical channel used
• Similar to common channel signaling for circuit switching services
• Data link layer
• LAPD (Q.921)
• Reliable data link control
• Error and flow control
• Between user (TE) and network (NT)
• Used for exchange of Q.933 control signal messages

User Plane

• End to end functionality
• Transfer of info between ends
• LAPF (Link Access Procedure for Frame Mode Bearer Services) Q.922
• Frame delimiting, alignment and transparency
• Frame mux and demux using addressing field
• Ensure frame is integral number of octets (zero bit insertion/extraction)
• Ensure frame is neither too long nor short
• Detection of transmission errors
• Congestion control functions

​

​

User Data Transfer

• One frame type
• User data
• No control frame
• No inband signaling
• No sequence numbers
• No flow nor error control

​

Required Reading

• Stallings Chapter 10
• ITU-T web site
• Telephone company web sites (not much technical info - mostly marketing)
• X.25 info from ITU-T web site
• Frame Relay forum

​

Thank You