1 of 28

Pneumatic Bumper Car

Submitted By:- Supervisor By:-

1. Naveen Kumar (15ME010) Mr. Kavi Grover

2. Rahul (15ME011) Assistant Professor

3. Jitendra Singh (15ME007)

4. Hemant (15ME004)

5. Indresh Ray (15ME005)

​

​

​

SCHOOL OF ENGINEERING & TECHNOLOGY

Department of Mechanical Engineering

BATCH (2015-2019)

2 of 28

Pneumatic Bumper Car

3 of 28

  • Contents

​

1. Introduction

2. Parts

3. Construction & Working

4. Advantages & Limitation

5. Conclusion

4 of 28

Introduction

  • India is the developing country. India is a densely populated country with the vehicle usage being really diverse. While the available resources which are used to run the vehicles like road quality & new technologies in vehicles are being developed to avoid accidents. The number of people expired during vehicle accidents is very large as compared to the other causes of death.

​

…..Continued

5 of 28

  • Though there are different causes for accidents but proper technology of braking system and technology to reduce the damage during accident should be developed.

​

  • Hence there is need of Impact Reduction system to prevent the accidents and to reduce the damage to vehicle and also the driver.

​

  • To achieve this goal, we design this prototype of Pneumatic Bumper Car. Our aim is to design & develop automatic control system based on intelligent electronic control automotive bumper activation system called β€œ PNEUMATIC BUMPER CAR ’’.

​

6 of 28

Parts

  1. PISTON.
  2. SOLENOID VALVE.
  3. AC MOTOR.
  4. RELAY.
  5. FABRICATION.
  6. BATTERY.
  7. COMPRESSOR.

​

​

7 of 28

1.PISTONοΏ½οΏ½

8 of 28

  • It’s means that the air pressure operates on the forward and backward strokes. The air from the compressor is passed through the solenoid valve which controls the pressure to the required amount by adjusting its knob.οΏ½

9 of 28

2. SOLENOID VALVE

10 of 28

  • It is a flow control device used in pneumatic system to change the direction of air flow. Solenoid valve is used in automatic bumper system to control the compressed air towards the pneumatic cylinder during the extraction of the bumper.

11 of 28

3. AC MOTOR.

12 of 28

  • An electric motor is an electrical machine that converts electrical energy into mechanical energy. Electric motors are used to produce linear or rotary force (torque). Gears will be attached to the motor which will help driving the chain drive which in turn will move our vehicle.

13 of 28

4. RELAY

14 of 28

  • It is a control unit having certain specifications. This control unit acts according to the sensor signal to activate the Bumper with the help of compressed air through solenoid valve.

15 of 28

5. FABRICATION

16 of 28

  • FRAME WITH AXLE AND WHEELS.
  • Initially frame is constructed in rectangular shape by welding angle bar. Then the four angle bars are welded to the main rectangular frame in order to mount all other components.

17 of 28

6. BATTERY

18 of 28

  • A container consisting of one or more cells, in which chemical energy is converted into electricity and used as a source of power.
  • Voltage: 12V

Current : 7Amp.

19 of 28

6. COMPRESSOR

20 of 28

CONSTRUCTION AND WORKING

  • As this system is used at the time of emergency during work. In normal travelling of vehicle this system can be switched of with the help of a switch and it will not affect the normal working of the vehicle When any obstacle, human, animal or vehicle comes in front of the vehicle then the installed infrared sensor senses the obstacle. The range of distance between the vehicle and obstacle is variable. This range is varied according to the density of vehicles or humans on road. The received signal by IR sensor is provided to the control unit .
  • ……continued

21 of 28

  • When any obstacle, humans, animals or vehicle is came in front of the vehicle then the installed infrared sensor senses that obstacle. The range of distance between the vehicle and obstacle is variable. This range is varied according to the density of vehicles or humans on road.
  • The received signal by IR sensor is provided to the control unit. The control unit then activates the Solenoid Valve which will allow the flow of compressed air through it.

22 of 28

  • Compressed air is provided as an Input to the Solenoid Valve which has two Outputs both connected to the Double Acting Pneumatic Cylinder This pneumatic force of the compressed air through the Solenoid Valve is transferred to the Bumper System. The pneumatic force provides forward motion to the Bumper and it also retracts the bumper slowly reducing the impact.
  • Hence, when the external body is kept safe, there will be no chance of internal damage.

​

23 of 28

ADVANTAGE & LIMITATION

24 of 28

ADVANTAGES

  • Simple construction of the prototype vehicle.
  • It provides safety to passengers in the vehicle as well as to the vehicle body.
  • It reduces accident intensity and impact.
  • This system increases the response time of vehicle braking by keeping safe distance between two vehicles.
  • The design also increases the crashing distance by providing extra space due to extension of the bumper, decreasing the chances of injuries to commuters.

25 of 28

LIMITATION

  • Additional cost is required to install this arrangement in the vehicle.
  • Vehicle speed above 40-50 km/h.

26 of 28

CONCLUSION

Behind the designing of this system, our main aim is to improve the technique of prevention of accidents and also reducing the hazard from accidents like damage of vehicle, injury of humans, etc.

​

This project work has provided us an excellent opportunity and experience, to use our limited knowledge. We have gained practical knowledge regarding, planning, purchasing, assembling and machining while doing this project work.

​

In conclusion remarks of our project work, we have developed an β€œACCIDENT PREVENTION SYSTEM BY AUTOMATIC PNEUMATIC BUMPER” which helps to achieve low Impact damage.

27 of 28

β€œ We are proud that we have completed the work with the limited time successfully. We have done the project to our ability and skill making maximum use of available facilities and we are able to understand the difficulties in maintaining the quality. We have also observed that the prototype manufactured is working with satisfactory conditions and our work is able to achieve all the objectives which are necessary.”

Declaration

28 of 28

THANK YOU