MAURBHANJ SCHOOL OF ENGINEERING�BARIPADA : 757107 , ODISHA�
Branch : Mechanical Engineering
Semester : 4th Sem
Subject : THEORY OF MACHINE
Topic : GOVERNOR
Faculty : Er. A DAS
STUDY �OF� GOVERNOR
INTRODUCTION
The function of governor is to regulate the speed of an engine when there are variation in the load
Eg. When the load on an engine increases, its speed decreases, therefore it is necessary to increase the supply of working fluid & vice-versa. Thus, Governor automatically controls the speed under varying load.
Types of Governors:
The governors may broadly be classified as
The centrifugal governors may further be classified as follows:
Centrifugal governor
Pendulum type
Loaded type
Watt governor
Dead weight governor
Spring controlled governor
Porter governor
Proell governor
Pickering governor
Hartung governor
Wilson - Hartnel governor
Hartnell governor
CENTRIFUGAL GOVERNORS
The centrifugal governors are based on the balancing of centrifugal force on the rotating balls for an equal and opposite radial force, known as the controlling force. It consist of two balls of equal mass, which are attached to the arms as shown in fig. These balls are known as governor balls or fly balls.
when the load on the engine increases, the engine and the governor speed decreases. This results in the decrease of centrifugal force on the balls. Hence the ball moves inward & sleeve moves downwards. The downward movement of sleeve operates a throttle valve at the other end of the bell rank lever to increase the supply of working fluid and thus the speed of engine is increased. In this case the extra power output is provided to balance the increased load.
When the load on the engine decreases, the engine and governor speed increased, which results in the increase of centrifugal force on the balls. Thus the ball move outwards and sleeve rises upwards. This upward movement of sleeve reduces the supply of the working fluid and hence the speed is decreased. In this case power output is reduced.
Watt Governor
It is the simplest form of centrifugal governor. It is basically a conical pendulum with links attached to a sleeve of negligible mass. The arms of governors may be connected to the spindle in following three ways;
Let,
m = Mass of the Ball in Kg
w = Weight of the ball in Newton (= m.g)
T = Tension in the arm in N
rad/sec.
r = Radius of path of rotation of ball in mtrs.
Fc = Centrifugal force acting on the balls in Newtons (m ω2r)
h = Height of governor in mtrs.
Fc x h = W x r
mr ω2 x h = m.g.r
h = g / ω2
When g is in m/s2 and ω is in rad/sec, then h is in mtrs. If N is the speed in r.p.m. then
ω = 2ΠN / 60
H = 9.81 / (2ΠN / 60)
= 895 / N2 mtrs.
Final Equations:
Porter governor
The porter governor is a modification of a Watt’s governor, with central load attached to the sleeve. The load moves up and down the central spindle. This additional downward force increases the speed of revolution required to enable the balls to rise to any predetermined level.
Let,
m = mass of each ball
w = Wt. of each ball
M = mass of central load
W = Wt. of central load
r = Radius o rotation
h = Height of governor
N = Speed o ball in r.p.m.
ω = Angular speed o balls
Fc = centrifugal force
Let,
T1 = Force on the arm
T2 = Force in the links
α = Angle of inclination of arm to vertical
β = Angle of inclination of link to vertical
Final Equations:
mg + ( M.g ± F)/2
m.g
2)
N2
=
x
895
h
(1+q)
x
With Friction
3)
h
=
(m + M)
m
x
g
ω2
1)
N2
=
(m + M)
m
x
895
h
Without Friction
Proell Governor
The Proell governor has the balls fixed at B & C to the extension of the links DF & EG, as shown. The arms FP & GQ are pivoted at p & Q respectively.
Consider the equilibrium of the forces on one half of the governor. The instantaneous centre (I) lies on the intersection of the line PF produced and the line from the D drawn perpendicular to the spindle axis. The perpendicular BM is drawn on ID
Final Equations:
1)
N2
=
(m + M)
m
x
895
h
Since h is in mtrs.
FM
BM
Hartnell Governor
It is a spring loaded governor, consists of two bell crank levers pivoted at the pts. O, O to the frame. Frame is attached to the governor spindle and therefore rotates with it. Each lever carries a ball at the end of the vertical arm OB & a roller at the end of horizontal arm OR. A helical spring in compression provides equal downward forces on two rollers through collar on the sleeve. The spring force may be adjusted by screwing a nut up or down on the sleeve.
Let,
m = mass of each ball
M = Mass of sleeve in kg.
r1 = Minimum radius of rotation
r2 = maximum radius of rotation
r = Distance of fulcrum O from gov. axis.
ω1 = Angular speed of governor at r1
ω2 = Angular speed of governor at r2
S1 = Spring force exerted on the sleeve at ω1
S2 = Spring force exerted on the sleeve at ω2
Fc1 = centrifugal force at ω1
Fc2 = centrifugal force at ω2
S = Stiffness of the spring
X = Length of vertical or ball arm
Y = length of horizontal or sleeve arm
Final Equations:
S
=
S2 – S1
h
=
2
Fc2 – Fc1
r2 – r1
x
y
2
Fc
=
Fc1 + (Fc2 – Fc1)
r – r1
r2 – r1
=
Fc2 -- (Fc2 – Fc1)
r2– r
r2 – r1
Hartung Governor
A spring controlled governor of Hartung type is shown in fig. In this type of governor, the vertical arms of the bell crank levers are fitted with spring balls which compress against the frame of the governor when the rollers at the horizontal arm press against the sleeve.
Wilson - Hartnell Governor
It is a governor in which the balls are connected by a spring in tension as shown. An auxiliary spring is attached to the sleeve mechanism, through lever by means of which equilibrium speed for a given radius may e adjusted. The main spring may e considered of two equal parts each belonging to both the balls.
Pickering Governor
It is mostly used for driving gramophone. It consists of three straight leaf springs arranged at equal angular intervals round the spindle. Each spring carries a weight at the centre. The weights move outwards and the springs bend as they rotate about the spindle axis with increasing speed.
CONCLUSION :-
In this way we have studied aout the various types and working of different governors.