Agarose Gel electrophoresis

Agarose Gel Electrophoresis

​

​

Gel electrophoresis is a procedure that separates molecules on the basis of their rate of movement through a gel under the influence of an electrical field.

​

​

• DNA is negatively charged.

• An agarose gel is used to slow the movement of DNA and separate by size.

How fast will the DNA migrate?

strength of the electrical field, buffer, density of agarose gel…

Size of the DNA!

*Small DNA move faster than large DNA

…gel electrophoresis separates DNA according to size

small

large

Within an agarose gel, linear DNA migrate inversely proportional to the log10 of their molecular weight.

Agarose

Agarose is a linear polymer extracted from seaweed.

D-galactose

3,6-anhydro

L-galactose

• Sweetened agarose gels have been eaten in the Far East since the 17th century.

​

• Agarose was first used in biology when Robert Koch* used it as a culture medium for Tuberculosis bacteria in 1882

*Lina Hesse, technician and illustrator for a colleague of Koch was the first to suggest agar for use in culturing bacteria

​

Making an Agarose Gel

An agarose gel is prepared by combining agarose powder and a buffer solution.

Agarose

Buffer

Flask for boiling

Casting tray🡭

Gel combs🡭

Power supply🡪

Gel tank🡪

🡯Cover

Electrical leads

🡫

Electrophoresis Equipment

Gel casting tray & combs

Seal the edges of the casting tray and put in the combs. Place the casting tray on a level surface. None of the gel combs should be touching the surface of the casting tray.

Preparing the Casting Tray

Agarose

Buffer Solution

Combine the agarose powder and buffer solution. Use a flask that is several times larger than the volume of buffer.

Agarose is insoluble at room temperature (left).

The agarose solution is boiled until clear (right).

Gently swirl the solution periodically when heating to allow all the grains of agarose to dissolve.

***Be careful when boiling - the agarose solution may become superheated and may boil violently if it has been heated too long in a microwave oven.

Melting the Agarose

Allow the agarose solution to cool slightly (~60ºC) and then carefully pour the melted agarose solution into the casting tray. Avoid air bubbles.

Pouring the gel

Each of the gel combs should be submerged in the melted agarose solution.

When cooled, the agarose polymerizes, forming a flexible gel. It should appear lighter in color when completely cooled (30-45 minutes). Carefully remove the combs and tape.

Place the gel in the electrophoresis chamber.

buffer 🡺

Add enough electrophoresis buffer to cover the gel to a depth of at least 1 mm. Make sure each well is filled with buffer.

🡬Cathode

(negative)

Anode🡭

(positive)

🡩

wells

🡩

🡩

🡩

DNA🡺

6X Loading Buffer: 🡪

∙ Bromophenol Blue (for color)

∙ Glycerol (for weight)

Sample Preparation

Mix the samples of DNA with the 6X sample loading buffer (w/ tracking dye). This allows the samples to be seen when loading onto the gel, and increases the density of the samples, causing them to sink into the gel wells.

Loading the Gel

Carefully place the pipette tip over a well and gently expel the sample. The sample should sink into the well. Be careful not to puncture the gel with the pipette tip.

Place the cover on the electrophoresis chamber, connecting the electrical leads. Connect the electrical leads to the power supply. Be sure the leads are attached correctly - DNA migrates toward the anode (red). When the power is turned on, bubbles should form on the electrodes in the electrophoresis chamber.

Running the Gel

🡨 wells

🡨 Bromophenol Blue

Cathode

(-)

Anode

(+)

Gel

After the current is applied, make sure the Gel is running in the correct direction. Bromophenol blue will run in the same direction as the DNA.

DNA

(-)

🡫

DNA Ladder Standard

Inclusion of a DNA ladder (DNAs of know sizes) on the gel makes it easy to determine the sizes of unknown DNAs.

-

+

bromophenol blue🡪

Note: bromophenol blue migrates at approximately the same rate as a 300 bp DNA molecule

Staining the Gel

***CAUTION! Ethidium bromide is a powerful mutagen and is moderately toxic. Gloves should be worn at all times.

• Ethidium bromide binds to DNA and fluoresces under UV light, allowing the visualization of DNA on a Gel.

​

• Ethidium bromide can be added to the gel and/or running buffer before the gel is run or the gel can be stained after it has run.

Safer alternatives to Ethidium Bromide

​

∙ Methylene Blue

​

∙ BioRAD - Bio-Safe DNA Stain

​

• Ward’s - QUIKView DNA Stain

​

• Carolina BLU Stain

​

…others

advantages

Inexpensive

Less toxic

No UV light required

No hazardous waste disposal

disadvantages

Less sensitive

More DNA needed on gel

Longer staining/destaining time

​

Staining the Gel

• Place the gel in the staining tray containing warm diluted stain.

• Allow the gel to stain for 25-30 minutes.

• To remove excess stain, allow the gel to destain in water.

• Replace water several times for efficient destain.

Ethidium Bromide requires an ultraviolet light source to visualize

Visualizing the DNA (ethidium bromide)

Samples # 1, 4, 6 & 7 were positive for Wolbachia DNA

Primer dimers🡪

Visualizing the DNA (QuikVIEW stain)

🡨 250

🡨 1,500

🡨 1,000

🡨 500

🡨 750

🡨 2,000 bp

DNA ladder

🡫

PCR

Product

wells🡪

+ - - - - + + - - + - +

March 12, 2006

Samples # 1, 6, 7, 10 & 12 were positive for Wolbachia DNA