1 of 45

A COMPARATIVE STUDY OF SILICA AND IRON CONTENT FOR BAUXITE ORE AND ITS WASTE PRODUCTS

PRESENTED BY :

Sonal (1801227517)

Soumya Ranjan Panda (1801227525)

Awhan Parasar (1801227123)

​

UNDER THE GUIDANCE OF :

Asst. Prof. Rudra Narayan Mohapatra

DEPARTMENT OF CHEMICAL ENGINEERING

C V RAMAN GLOBAL UNIVERSITY,

BHUBANESWAR

2 of 45

CONTENTS

  • ABSTRACT
  • INTRODUCTION
  • LITERATURE REVIEW
  • OBJECTIVE
  • PROCEDURE
  • CALCULATIONS
  • RESULTS AND DISCUSSIONS
  • CONCLUSIONS
  • FUTURE WORKS
  • REFERENCES

3 of 45

ABSTRACT

  • Bauxite contains silica and iron as impurities which reduces its quality. Also, the two major waste products of bauxite mining, namely PLK rocks and Red mud, contain ample amounts of iron oxides as well as silica as impurities.
  • Both silica and iron form complexes with the caustic used during the processing of ore thereby forming precipitates which results in unnecessary wastage of caustic that contributes to increased processing costs.
  • We decided to go for both physical and chemical methods to determine silica content in Bauxite ore, PLK rocks and Red mud.

​

4 of 45

  • And for the determination of iron content in the aforementioned materials we go for just the chemical method.
  • As a result of all the process we were able to present a very vivid comparison of silica content from physical method and chemical method as well as among the materials itself.
  • Also, we were able to produce a comparison of iron content in the feed material and in the sample, we used for silica content determination.
  • For the physical method of silica content determination, we used the spiral separation method.

5 of 45

INTRODUCTION

  • The main source of Aluminium is bauxite ore which majorly consists of various hydrates of aluminium. They vary physically depending on the origin and geographic history of the deposits. Bauxite ore is formed by the weathering of various rocks.
  • Silica and iron make up the major impurities present in bauxite ore which also degrades its quality. On top of that, it reacts with caustic to form complexes during the processing, resulting into precipitate formation, and unnecessary increase in processing costs.
  • The amount of silica or iron has been known to vary place to place or throughout processes. PLK rocks and Red mud are the two major waste/by-products generated during Bauxite mining.

6 of 45

  • Red mud is a waste generated due the processing of bauxite into aluminium by Bayer’s process. It comprises different oxides including iron, which give its red colour.
  • PLK rocks or Partially Lateritised Khondalite rocks are the waste products of bauxite ore mining and have a high iron oxide content.
  • To achieve our results for the physical process, as already mentioned we are using wet spiral separator in addition with various types of crushers, sieve shaker and hot air oven for drying.
  • For the chemical method to analyze the silica and iron content of the three samples; we used an extensive chemical treatment process involving various chemicals mentioned later and some supplementary processes such as filtration and titration.

7 of 45

LITERATURE REVIEW

AUTHOR’S NAME

JOURNAL NAME AND PAPER DETAIL

Baudet, G. 

The dicalcium silicate Residue being produced, while using basic process on clays or anorthosites can be used in manufacture of Portland cementA documentary study on alumina extraction processes. Bureau de Recherché et Minieres Mission Arabic Saoudite. Departement mineralurgie. Orleans Cedex Fevriev, (1977).

Chai, W., Han, G., Huang, Y., Cao, Y., & Liu, J.

In this study, the desulfurization and desilication of low-quality bauxite ore by reverse flotation process, at the same time were observed Synchronous Desulfurization and Desilication of Low-Grade and High-Sulfur Bauxite by a Flotation Process. In Light Metals 2019 (pp. 35-38). Springer, Cham(2019). 

8 of 45

de Silva, H. 

In this the red mud particles are ultrasonically treated attend to disintegrate with particle size of about 250 nm after a treatment of 4-hour flotation experiment was carried our recovery of desilication product in alumina industry,(2014). 

Gomes, F. A. N., Barbota, C. N., Almeida, D. S. G., Sampaio, J. A.,

The detailed study of characterization showed that the bauxite contain patches of kaolinite associated with gibbsite, Reduction of Reactive Silica from Bauxite, Conference: 19th Symposium of ICSOBA, At: Belém, Pará / Brazil, Volume: v1, Pages 16-21.(2012). 

Hind, A. R., Bhargava, S. K., & Grocott, S. C. 

In this the reaserchers studied about the firing is that Bauxite is produced as a refining product to smelting grade alumina, from the process known as Bayer process,.(1999). The surface chemistry of Bayer process solids: a review. Colloids and surfaces A: Physicochemical and engineering aspects, 146(1-3), 359-374.

Jayalatharachc V. 

In this the author found out that desilication products have larger percentage in bauxite reduce 0 to 24% sodalite,  0 to 50% cancrinite  whose chemical and physical properties depend on nature of bauxite Understanding desilication products in bauxite refinery residues (Doctoral dissertation, Queensland University of Technology),(2016). 

9 of 45

 Kaußen, F. M., & Friedrich, B. 

In this the author mentions the possibility of capturing silica by addition of lime in order to form dicalcium silicates(2016). Methods for alkaline recovery of aluminum from bauxite residue. Journal of Sustainable metallurgy, 2(4), 353-364.

Klauber, C., Gräfe, M., & Power, G. 

 Studied about firing that in the whole world, the bauxite residue disposal areas contain minimum 2.7 billion tons of residue(2011). Bauxite residue issues: II. options for residue utilization. Hydrometallurgy, 108(1-2), 11-32.

Marino, S. L. 

��

In this we got that flotation can be applied in bauxite ores either by removing the impurities which is also known as reverse flotation or by floating the valuable minerals i.e., direct flotationThe Flotation of Marginal Gibbsitic Bauxite Ores from Paragominas--Brazil (Doctoral dissertation, Department of Metallurgical Engineering, University of Utah).(2012)

Massola, C. P., Chaves, A. P., Lima, J. R. B., & Andrade, C. F. 

 In this paper, the researchers come up with an innovative development in obtaining bauxite concentrates, that is by concentrating gibbsite via reverse froth flotation(2009). Separation of silica from bauxite via froth flotation. Minerals Engineering, 22(4), 315-318.

10 of 45

Mishra, B., Staley, A., & Kirkpatrick, D.  19

We've been known that further than 90 (by weight) alumina can be recovered from red slush by acidulous filtering and pop ash sintering(2002). Recovery of value-added products from red mud. Mining, metallurgy & Exploration, 19(2), 87-94.

Mohapatra, A., Bose, P., Pandit, S. S., Kumar, S., & Alex, T. C. 

In this Red mud and fly ash were obtained from HINDALCO Refinery, Ranchi for this experiment. The authors attempted to prepare geopolymer based products using these as raw materials ,Bulk Utilization of Red Mud in Geopolymer Based Products. Advances in Sciences and Engineering, 12(2), 86-91.(2020). 

Pan, X. L., Yu, H. Y., Dong, K. W., Tu, G. F., & Bi, S. W.

In this the author found out that the efficiency of desilication increases during the addition of lime in the process,Pre-desilication and digestion of gibbsitic bauxite with lime in sodium aluminate liquor. International Journal of Minerals, Metallurgy, and Materials, 19(11), 973-977,(2012). 

Peng, H., Peters, S., & Vaughan, J. 

��

In this research the authors identify the differences in the desilication of bauxite and activated bauxite Leaching Kinetics of Thermally-Activated, High Silica Bauxite. In Light Metals 2019 (pp. 11-17). Springer, Cham.(2019)

11 of 45

Peng,H. Seneviratne, D.&Vaughan, J. (2018).

 For this study, the authors precipitated DSP from synthetic NaOH–NaAl(OH)4–Na2SiO3–H2O solution at 75 and 90 °C Role of the amorphous phase during sodium aluminosilicate precipitation. Industrial & Engineering Chemistry Research, 57(5), 1408-1416

Rai, S., Lataye, D. H., Chaddha, M. J., Mishra, R. S., Mahendiran, P., Mukhopadhyay, J., ... & Wasewar, K. L. 

The authors in this paper talk about making an alternative building material using red mud,An alternative to clay in building materials: Red mud sintering using fly ash via Taguchi’s methodology. Advances in Materials Science and Engineering, 2013.

Saha, S.

It is a more affordable and environment friendly method of bio leaching of low-grade bauxite was discussed in the following paper. Biobeneficiation of bauxite ore through bacterial desilication (Doctoral dissertation)(2013).

Smith, P.

In this paper the author reviews many of the existing potential process applicable for high silica bauxite ores(2009). The processing of high silica bauxites—Review of existing and potential processes. Hydrometallurgy, 98(1-2), 162-176

Sukla, L. B., Pattanaik, A., & Pradhan, D.

In this process, the microorganisms and their biochemical products generate active redox environment to scatter or concentrate the various impurities present in the low-quality bauxite, here the Fe oxidizing and silicate bacterium eliminate Fe and solubilise silica.Advances in beneficiation of low-grade bauxite. In Light Metals 2019 (pp. 3-10). Springer, Cham(2019).

12 of 45

Swain, R., Padhy, L. N., & Rao, R. B. 

 In this paper the authors try to make bricks using the PLK waste obtained from bauxite mining, BENEFICIATION STUDIES ON BAUXITE MINING WASTE: A VALUE ADDITION FOR REFRACTORY INDUSTRIES. Iranian Journal of Materials Science and Engineering, 8(3), 37-49

Swain, R., Srinivas Rao, D., Vasumathi, N., Mohapatra, R., & Rao, R. B.

The authors, for this paper study characterization of PLK rocks obtained from bauxite mining at NALCO Orissa,Characterisation of Partially Lateritised Khondalite rock for value-added materials. International Journal of Mining and Mineral Engineering, 1(4), 383-396.

Ujaczki, É., Feigl, V., Molnár, M., Cusack, P., Curtin, T., Courtney, R., ... & Lenz, M

 In this paper the authors mention that with every passing day the world is facing increasing shortage of CRMs and so they talk about reusing bauxite residue by recovering the elements present in it,Re‐using bauxite residues: benefits beyond (critical raw) material recovery. Journal of Chemical Technology & Biotechnology, 93(9), 2498-2510.

Vafeias, M., Bagani, M., Xakalashe, B., Balomenos, Panias, D., Friedrich, B., 

 The results showed that temperature doesn't play a crucial role in aluminium extraction and that addition of NaOH assisted in silicon extraction.Alkaline Ammonia recovery from Bauxite residue slags, 3rd International Bauxite Residue Valorisation And Best Practices. (2020)

13 of 45

Vaughan, J., Peng, H., Seneviratne, D., Hodge, H., Hawker, W., Hayes, P., & Staker

In this the DSP concentrate which is obtained by physical separation from other components of bauxite Residue is used as a feed material for DSP concentrate sinter - leach process. The sandy desilication product process concept. Jom, 71(9), 2928-2935.(2019). 

Wellington, M., & Mandeville, J. W. 

In this the author reference lime as   aspirin of Bayer’s process because of its importance in   reduction impurities which impact Productivity of the process. Chem Xpress., 8(3), 208-213,(2015). 

Wu, H., Pan, X., Yu, H., & Bi, S. 

Results showed that by increasing the carbonate concentration, precipitation of cancrinite was increased too but it also reduced the crystallinity of several DSPs. Effect of Carbonate on Desilication of Sodium Aluminate Solution at High Temperature. JOM, 73(4), 1180-1187.(2021)

Wulandari,W.Purwasasmita, M.Sanwani, E. Pixelina, A. A., & Maulidan, A.

In this paper the authors apply the rear flotation system to separate silica from the bauxite ores acquired from west Kalimantan, Indonesia. (2017, January), to reduce reactive and non-reactive silica in bauxite ore from West Kalimantan. In AIP Conference Proceedings (Vol. 1805, No. 1, p. 050004). AIP Publishing LLC.

Xu, Y., Chen, C., Lan, Y., Wang, L., & Li, J. 

In this paper a combination of red mud and CaO as desilication reagent is better. It has a desilication ratio of ~89% Desilication and recycling of alkali-silicate solution seeded with red mud for low-grade bauxite utilization. Journal of Materials Research and Technology, 9(4), 7418-7426,(2020). 

14 of 45

OBJECTIVE

  • For this project we aim on presenting a comparative study of silica and iron contents in bauxite ore and its waste/by products. We’ll be using physical and chemical methods to determine the same.
  • A comparison of silica content determination through physical and chemical methods, a comparison of silica content among the materials will be presented.
  • An iron content comparison between feed sample and the sample used for silica content determination using chemical method; will be presented.

​

15 of 45

RED MUD

BAUXITE ROCK

PLK ROCK

16 of 45

PROCEDURE

The main procedure took place in the spiral separator. The procedure we followed for PLK rocks and Bauxite ore were similar, the procedure we followed for red mud was a little different. For red mud, we start from step-5. Following is a list of all the steps involved;

  • Step 1- The PLK sample was broken down into smaller pieces with the help of a hammer. Bauxite ore and red mud samples did not undergo this step.
  • Step 2- We used the jaw crusher to reduce the sample size of PLK rocks and bauxite ore upto 150-250mm size.
  • Step 3- The sample from jaw crusher was feed into roll crusher. The resultant sample was about 1-12mm in size.
  • Step 4- The output sample from roll crusher as feed into ball mill. It was rotated 500 times to obtain the output samples.

17 of 45

JAW CRUSHER

ROLL CRUSHER

BALL MILL

18 of 45

  • Step 5- We used the sieve shakers to separate various different particle sizes of the sample feed from ball mill. This step was applicable to all the three samples i.e. Bauxite ore, PLK rock and Red mud.

​

  • Step 6- We collected the -0.75𝞵m sample from the sieve shaker for further processing. 
  • In 3 different beakers of 1000ml capacity  each,  we mixed 500g of red mud sample in the first beaker, 100g of Bauxite ore sample in the second , and 1000g of PLK sample in the third one with water. 
  • For reference we named them sample 1, sample 2 and sample 3 respectively.

​

  • Step 7- First we washed down the spiral separator to remove any remaining foreign particles from previous experiments as a precaution. 
  • Then we started the water supply and adjusted its flow as per requirement. 
  • Sample 1 was slowly poured down from top of the separator, the slurry then divided into two different streams,  one majorly containing silica and the other non silica; while flowing down. 
  • These were collected from two different outlets into two different buckets. 

19 of 45

SEIVE SHAKER

SPIRAL SEPARATOR

20 of 45

For the chemical analysis to find the silica content we start by a chemical treatment process.

​

  • Step 1- Take 25gm samples of each; bauxite ore, red mud and PLK rock; in three different beakers; namely sample 1, sample 2, sample 3.

​

  • Step 2- Add 50gm of sodium hydroxide to each of the beakers and mix it well (sample:sodium hydroxide::1:2). Leave it in the hot oven for 2-3hrs at 170°C.

​

  • Step 3- Wash the three samples using distilled water and collect it in separate conical flasks. Filter this liquid sample to remove any solid particles of the material samples in question.

​

The following steps are performed while continually heating these samples on the hot plate, covered with a lead.

​

  • Step 4- Add 10ml of a diluted solution of sulphuric acid and water (1:9) and wait until the solution turns a bright shade of green.

21 of 45

CHEMICAL TREATMENT OF SAMPLES (i) RED MUD (ii) PLK ROCK AND (iii) BAUXITE ORE

(i) (ii) (iii)

  • Step 5- While continually stirring the solution, keep adding hydrogen peroxide at small intervals until the solution turned brownish.

​

  • Step 6- Remove the solution from the hot plate and let it cool down. Followed by filtering this brown solution for all the three samples to get a clear solution.

​

22 of 45

Following steps were followed for silica analysis;

​

  • Step1- Take10ml of the above obtained sample and added 20ml of sulphuric acid and heated it on the hot plate until all the liquid evaporated and we were left with a salt solution.

​

  • Step 2- Dry this salt solution in the hot air oven and the cool it down to retrieve the salt. And to this salt sample add 20ml distilled water and dehydrating it.

​

  • Step 3- Add about 1-2gm of pulp to the above obtained samples. Filter this solution and weigh it as the initial weight.

​

  • Step 4- Water wash these samples hot water (60˚C) 3-4 times and add a small amount of 1% Barium Chloride solution to it. Filter this solution and weigh it as the final weight.

23 of 45

BAUXITE SAMPLE WITH DILUTED SULPHURIC ACID ON HOT PLATE

SALT SOLUTION FORMS IN PLK ROCK SAMPLE

24 of 45

For the iron analysis we followed the following steps,

​

  • Step 1- We take two samples of each of the three materials; Bauxite ore, PLK rocks and Red mud; one of them being feed sample weighing 0.2gm and the other one was the chemically treated sample weighing 2ml.

​

  • Step 2- Add 20ml of hydrochloric acid to these samples and set them on the hot plate for continuous heating.

​

  • Step 3- Add stannous chloride dropwise while occasionally stirring and still on the hot plate until the solution losses its yellow colour. Set them aside to cool down.

​

  • Step 4- Add 5ml of lead chloride solution, a milky white precipitate is formed.

​

  • Step 5- Add 2-4ml of orthophosphoric acid and then a few drops of barium disulphate.

​

​

25 of 45

FEED SAMPLES READY FOR IRON ANALYSIS

  • Step 6- Titrate this solution against potassium dichromate and with barium disulphate as indicator. Note the initial and final readings of the burette until the solution turns to a violet colour.

​

For the iron analysis of the silica retrieved from the previous procedure of silica analysis, we followed the same steps as above.

26 of 45

CALCULATIONS

Following are the calculations to determine the silica percentage in our samples of Bauxite ore, PLK Rocks and Red mud.

​

  • For Bauxite ore,

Initial weight = 2.46gm

Final weight = 1.89gm

Weight of silica in 10ml of solution = Initial weight – Final weight

= (2.46 – 1.89) gm = 0.57gm

Weight of silica in 1ml of solution = 0.57gm/10 = 0.057gm

Percentage (%) of silica = 0.057 × 100 % = 5.7%

​

​

​

27 of 45

  • For PLK Rocks,

Initial weight = 1.475gm

Final weight = 1.025gm

Weight of silica in 10ml of solution = Initial weight – Final weight

= (1.475 – 1.025) gm = 0.45gm

Weight of silica in 1ml of solution = 0.45gm/10 = 0.045gm

Percentage (%) of silica = 0.045 × 100 % = 4.5%

  • For Red mud,

Initial weight = 1.028gm

Final weight = 0.543gm

Weight of silica in 10ml of solution = Initial weight – Final weight

= (1.028 – 0.543) gm = 0.435gm

Weight of silica in 1ml of solution = 0.435gm/10 = 0.0435gm

Percentage (%) of silica = 0.0435 × 100 % = 4.35%

28 of 45

Following are the calculations to determine the iron percentage in the feed samples of Bauxite ore, PLK Rocks and Red mud.

​

  • For Bauxite ore,

Initial reading = 22

Final reading = 26.5

Difference = 4.5

Iron percentage (%) = (4.5 × 0.005555 ×100)/0.2 = 12.49%

  • For PLK rocks,

Initial reading = 26.5

Final reading = 29.9

Difference = 3.4

Iron percentage (%) = (3.4 × 0.005555 ×100)/0.2 = 9.44%

​

29 of 45

  • For Red mud,

Initial reading = 12.5

Final reading = 22

Difference = 9.5

Iron percentage (%) = (9.5 × 0.005555 ×100)/0.2 = 26.38%

​

Following are the calculations to determine the iron percentage in the samples from silica analysis of Bauxite ore, PLK Rocks and Red mud.

​

  • For Bauxite ore,

Initial reading = 8.4

Final reading = 12.2

Difference = 3.8

Iron percentage (%) = (3.8 × 0.005555 × 10 × 100)/2 = 10.55%

​

30 of 45

  • For PLK Rocks,

Initial reading = 4

Final reading = 8.4

Difference = 4.4

Iron percentage (%) = (4.4 × 0.005555 × 10 × 100)/2 = 12.22%

​

  • For Red mud,

Initial reading = 12.2

Final reading = 22.4

Difference = 10.2

Iron percentage (%) = (10.2 × 0.005555 × 10 × 100)/2 = 28.33%

​

31 of 45

RESULTS AND DISCUSSIONS

For physical silica analysis,

  • Bauxite ore had 22% silica containing part.
  • PLK Rock had 39.7% silica containing part.
  • Red mud had 36.4% silica containing part.

SILICA AND NON-SILICA SAMPLES OF (i) RED MUD (ii) BAUXITE ORE (iii) PLK ROCK

(i) (ii) (iii)

32 of 45

RESULTANT SAMPLE WEIGHTS FROM PHYSICAL SILICA ANALYSIS

BAR GRAPH REPRESENTATION OF DATA ACQUIRED THROUGH PHYSICAL SILICA ANALYSIS

33 of 45

For the chemical analysis to determine silica content,

  • Bauxite ore has 5.7% silica content
  • PLK rocks contain 4.5% silica
  • Red mud has about 4.35% of silica.

PERCENTAGE OF SILICA CONTENT DETERMINED VIA PHYSICAL AND CHEMICAL ANALYSIS

34 of 45

For the chemical analysis to determine iron content in the feed sample,

  • Bauxite ore contained around 12.49% iron
  • PLK Rock contained 9.44% iron
  • Red mud contained 26.38% of iron.

GRAPH REPRESENTING THE COMPARISON OF SILICA CONTENT DETERMINED THROUGH CHEMICAL AND PHYSICAL ANALYSIS

35 of 45

For the chemical analysis to determine iron content of chemically treated samples,

  • Bauxite ore contains 10.55% of iron
  • PLK Rocks contain 12.22% of iron
  • Red mud contained 28.33% iron.

​

Finally, for chemical analysis to determine iron content of retrieved silica samples from all the three materials in consideration,

  • Silica sample retrieved from Bauxite ore contained 1.11% iron
  • Silica sample from PLK rocks contained 0.83% of iron
  • Silica sample from Red mud contained 1.66% of iron.

​

36 of 45

COMPARISON OF IRON CONTENT IN FEED SAMPLE VS CHEMICALLY TREATED SAMPLE VS RETRIEVED SILICA SAMPLE

IRON CONTENT PERCENTAGE IN FEED SAMPLE, CHEMICALLY TREATED SAMPLE AND RETRIEVED SILICA SAMPLE

37 of 45

CONCLUSION

  • As per the results and after comparing it, we come to the conclusion that using a spiral separator for physical analysis can be quite feasible in case of red mud and PLK rocks.
  • Also, we conducted only one round on the spiral separator but if we do another one or two rounds on the separator with the silica samples, we’ll be able to come up with a more accurate silica percentage.
  • But as this takes a lot of time and labor, with the physical analysis being cheap and environment friendly it’ll also take time, which might not be as efficient as needed in many situations.
  • For the chemical analysis for finding both the silica content and iron content, it was a success.

38 of 45

  • The retrieved silica sample from silica analysis, we found out that there were still a little amount (<2%) of iron left in those samples which can be removed by further processings.
  • The silica content results of samples through physical analysis were way more than the ones from chemical analysis method.
  • This signifies that there were a lot of impurities in the case of physical analysis and the results were almost on point and very precise in the case of chemical analysis.

39 of 45

FUTURE WORKS

  • We would conclude this project here only, but since there’s always room for development we’d want; for anyone who wishes; to continue working on this topic and find even more feasible methods and accurate results for the development of the Aluminium Industry.
  • Also, a use for these silica and iron free samples in industries could be worked upon.
  • The extracted silica and iron can also be put to use in the industry as raw materials for the production of different products.

40 of 45

REFERENCES

  • Baudet, G. (1977). ‘A documentary study on alumina extraction processes’. Bureau de Recherché et Minieres Mission Arabic Saoudite. Departement mineralurgie. Orleans Cedex Fevriev.
  • Chai, W., Han, G., Huang, Y., Cao, Y., & Liu, J. (2019). ‘Synchronous Desulfurization and Desilication of Low-Grade and High-Sulfur Bauxite by a Flotation Process’. In Light Metals 2019 (pp. 35-38). Springer, Cham.
  • de Silva, H. (2014). ‘Recovery of desilication product in alumina industry’.
  • Gomes, F. A. N., Barbota, C. N., Almeida, D. S. G., Sampaio, J. A., (2012). ‘Reduction of Reactive Silica from Bauxite’. Conference: 19th Symposium of ICSOBA, At: Belém, Pará / Brazil, Volume: v1, Pages 16-21.
  • Hind, A. R., Bhargava, S. K., & Grocott, S. C. (1999).’ The surface chemistry of Bayer process solids: a review’. Colloids and surfaces A: Physicochemical and engineering aspects, 146(1-3), 359-374.

41 of 45

  • Jayalatharachchi, V. (2016). ‘Understanding desilication products in bauxite refinery residue’s (Doctoral dissertation, Queensland University of Technology).
  • Kaußen, F. M., & Friedrich, B. (2016). ‘Methods for alkaline recovery of aluminum from bauxite residue’. Journal of Sustainable metallurgy, 2(4), 353-364.
  • Klauber, C., Gräfe, M., & Power, G. (2011). ‘Bauxite residue issues: II. options for residue utilization’. Hydrometallurgy, 108(1-2), 11-32.
  • Marino, S. L. (2012). ‘The Flotation of Marginal Gibbsitic Bauxite Ores from Paragominas—Brazil’ (Doctoral dissertation, Department of Metallurgical Engineering, University of Utah).
  • Massola, C. P., Chaves, A. P., Lima, J. R. B., & Andrade, C. F. (2009). ‘Separation of silica from bauxite via froth flotation’. Minerals Engineering, 22(4), 315-318.
  • Mishra, B., Staley, A., & Kirkpatrick, D. (2002). ‘Recovery of value-added products from red mud. Mining, metallurgy & Exploration’. 19(2), 87-94.
  • Mohapatra, A., Bose, P., Pandit, S. S., Kumar, S., & Alex, T. C. (2020). Bulk ‘Utilization of Red Mud in Geopolymer Based Products’. Advances in Sciences and Engineering, 12(2), 86-91.

​

42 of 45

  • Pan, X. L., Yu, H. Y., Dong, K. W., Tu, G. F., & Bi, S. W. (2012). ‘Pre-desilication and digestion of gibbsitic bauxite with lime in sodium aluminate liquor’. International Journal of Minerals, Metallurgy, and Materials, 19(11), 973-977.
  • Peng, H., Peters, S., & Vaughan, J. (2019). ‘Leaching Kinetics of Thermally-Activated, High Silica Bauxite’. In Light Metals 2019 (pp. 11-17). Springer, Cham.
  • Peng, H., Seneviratne, D., & Vaughan, J. (2018). ‘Role of the amorphous phase during sodium aluminosilicate precipitation’. Industrial & Engineering Chemistry Research, 57(5), 1408-1416.
  • Rai, S., Lataye, D. H., Chaddha, M. J., Mishra, R. S., Mahendiran, P., Mukhopadhyay, J., ... & Wasewar, K. L. (2013). ‘An alternative to clay in building materials: Red mud sintering using fly ash via Taguchi’s methodology’. Advances in Materials Science and Engineering, 2013.
  • Saha, S. (2013). ,Biobeneficiation of bauxite ore through bacterial desilication’ (Doctoral dissertation)
  • Smith, P. (2009). ‘The processing of high silica bauxites—Review of existing and potential processes’. Hydrometallurgy, 98(1-2), 162-176

43 of 45

  • Sukla, L. B., Pattanaik, A., & Pradhan, D. (2019). ‘Advances in beneficiation of low-grade bauxite’. In Light Metals 2019 (pp. 3-10). Springer, Cham
  • Swain, R., Padhy, L. N., & Rao, R. B. (2011). ‘Beneficiation studies on Bauxite mining waste: A value addition for Refractory Industries’. Iranian Journal of Materials Science and Engineering, 8(3), 37-49
  • Swain, R., Srinivas Rao, D., Vasumathi, N., Mohapatra, R., & Rao, R. B. (2009). ‘Characterisation of Partially Lateritised Khondalite rock for value-added materials’. International Journal of Mining and Mineral Engineering, 1(4), 383-396.
  • Ujaczki, É., Feigl, V., Molnár, M., Cusack, P., Curtin, T., Courtney, R., ... & Lenz, M. (2018). ‘Re‐using bauxite residues: benefits beyond (critical raw) material recovery’. Journal of Chemical Technology & Biotechnology, 93(9), 2498-2510.
  • Vafeias, M., Bagani, M., Xakalashe, B., Balomenos, Panias, D., Friedrich, B., (2020). ‘Alkaline Ammonia recovery from Bauxite residue slags’. 3 Rd International Bauxite Residue Valorisation And Best Practices.
  • Vaughan, J., Peng, H., Seneviratne, D., Hodge, H., Hawker, W., Hayes, P., & Staker, W. (2019). ‘The sandy desilication product process concept’. Jom, 71(9), 2928-2935.

44 of 45

  • Wellington, M., & Mandeville, J. W. (2015). ‘Effect of lime causticization on silica, calcium, oxalate and organic carbon levels in Bayer process washer overflow liquor’. Chem Xpress., 8(3), 208-213
  • Wu, H., Pan, X., Yu, H., & Bi, S. (2021). ‘Effect of Carbonate on Desilication of Sodium Aluminate Solution at High Temperature’. JOM, 73(4), 1180-1187.
  • Wulandari, W., Purwasasmita, M., Sanwani, E., Pixelina, A. A., & Maulidan, A. (2017, January). ‘Implementation of reverse flotation method to reduce reactive and non-reactive silica in bauxite ore from West Kalimantan’. In AIP Conference Proceedings (Vol. 1805, No. 1, p. 050004). AIP Publishing LLC.
  • Xu, Y., Chen, C., Lan, Y., Wang, L., & Li, J. (2020).’ Desilication and recycling of alkali-silicate solution seeded with red mud for low-grade bauxite utilization.’ Journal of Materials Research and Technology, 9(4), 7418-7426

​

45 of 45

THANK YOU