1 of 25

SERIES CIRCUITS

One path. Same current. Predictable voltage drops.

Technology Commons · CC BY-SA 4.0 · TEJ Electronics

2 of 25

What you will be able to do

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

02

LEARNING GOALS

•

Recognize a series circuit as one current path.

•

Calculate total resistance and circuit current.

•

Calculate voltage drops and check them with Kirchhoff’s voltage law.

•

Calculate power and choose a safe resistor rating.

WHY THIS MATTERS

Series calculations let you predict a real circuit before you build it. You will use the same process when you size indicator resistors, troubleshoot wiring, and analyse sensor circuits.

Reference: Grob’s Basic Electronics, Chapter 4.

3 of 25

A real series circuit

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

03

Follow the current path

•

Start at the positive terminal.

•

Pass through each component.

•

Return to the source.

•

There is only one path.

If one connection opens, current stops everywhere.

4 of 25

From the real circuit to the schematic

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

04

Physical circuit

Schematic model

The schematic shows electrical connections—not where parts sit on the table.

5 of 25

Watch the idea, then work the numbers

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

05

1

Conceptual introduction

2

Guided calculations

3

Alternate explanation

After each video, sketch the current path and write one prediction.

6 of 25

Series and parallel are different structures

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

06

SERIES · one path · same current

PARALLEL · several paths · same two nodes

7 of 25

Series rule 1 · Current is the same everywhere

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

07

Iₜ = I₁ = I₂ = I₃

There is no branch where current can split.

Measurement check

An ammeter should read the same current at every point in the loop.

8 of 25

Series rule 2 · Resistances add

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

08

Rₜ = ΣRᵢ + …

Adding a series resistor increases total resistance. If the source voltage stays the same, circuit current decreases.

Quick check: Rₜ must be larger than any one resistor.

9 of 25

Series rule 3 · Voltage drops add to the source

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

09

Vₜ = ΣVᵢ + …

Kirchhoff’s voltage law

Around one closed loop, the voltage rises and drops add to zero.

Use the source voltage to check your calculated drops.

10 of 25

Series rule 4 · Power and resistor safety

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

10

Pₜ = VₜIₜ

Pₜ = P₁ + P₂ + P₃ + …

P = I²R P = V²/R

A resistor’s power rating is a limit.

Choose a rating above the calculated dissipation. Do not operate a classroom resistor at its maximum rating.

The smallest allowable current limits the whole series circuit.

11 of 25

Series-circuit rules · Quick reference

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

11

12 of 25

Build and measure a series circuit

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

12

EQUIPMENT

•

Breadboard

•

Current-limited direct-current supply

•

Digital multimeter

•

Test leads and jumper wires

MEASURE AND CHECK

•

Current at four points

•

Each voltage drop

•

The source voltage

•

Calculated versus measured values

•

One clear photo of the circuit

Power off before measuring resistance. Put an ammeter in series.

13 of 25

Worked example · Start with the complete circuit

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

13

A 12.0 V source supplies three series resistors: 1.0 kΩ, 1.2 kΩ and 1.8 kΩ. Find total resistance, circuit current and every voltage drop. Check the result with Kirchhoff’s voltage law.

Use general equations before substituting numbers.

14 of 25

GUESS · Given and Unknown

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

14

G · GIVEN

U · UNKNOWN

Vₜ = 12.0 V

​

R₁ = 1.0 kΩ

​

R₂ = 1.2 kΩ

​

R₃ = 1.8 kΩ

Rₜ = ?

​

Iₜ = ?

​

V₁ = ?

​

V₂ = ?

​

V₃ = ?

15 of 25

GUESS · General equations

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

15

Rₜ = ΣRᵢ

Iₜ = Vₜ / Rₜ

Vᵢ = IₜRᵢ

Vₜ = ΣVᵢ

Select and rearrange the symbolic equation before inserting values.

16 of 25

GUESS · Substitute and solve

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

16

Keep full precision in calculator memory. Round only the final answers.

17 of 25

GUESS · State and check the answer

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

17

Rₜ = 4.0 kΩ Iₜ = 3.0 mA

V₁ = 3.0 V V₂ = 3.6 V V₃ = 5.4 V

Voltage-law check

3.0 V + 3.6 V + 5.4 V = 12.0 V ✓

The circuit current is 3.0 mA. The calculated voltage drops add to the 12.0 V source.

18 of 25

Casio fx-991ES PLUS C · One entry per line

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

18

Enter one calculation, then use Ans for the next step.

( 1.0 EXP 3 ) + ( 1.2 EXP 3 ) + ( 1.8 EXP 3 )

12.0 ÷ Ans

Ans × ( 1.0 EXP 3 )

3.0 + 3.6 + 5.4

Write units beside the result. Do not type units into the calculator.

19 of 25

Series Circuits A · Student problem set

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

19

•

1 · Complete series analysis

•

2 · Use a given current

•

3 · Choose a dropping resistor

•

4 · Work backward from one voltage drop

•

5 · Apply resistor power ratings

Solve each problem on paper with GUESS, then upload one clear photo for each question.

20 of 25

Question 1 · Complete analysis

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A · QUESTION 1

20

Problem

A 15.0 V source supplies three resistors in series: R₁ = 1.0 kΩ, R₂ = 2.2 kΩ and R₃ = 3.3 kΩ. Find Rₜ, Iₜ, V₁, V₂, V₃ and Pₜ. Show a Kirchhoff’s voltage-law check.

Use the general equations first · Show every GUESS step · Keep units with values · Round only the final answer

21 of 25

Question 2 · Current is given

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A · QUESTION 2

21

Problem

Two resistors, R₁ = 120 Ω and R₂ = 180 Ω, carry a series current of 15.0 mA. Find V₁, V₂, Vₜ and Pₜ.

Use the general equations first · Show every GUESS step · Keep units with values · Round only the final answer

22 of 25

Question 3 · Choose a dropping resistor

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A · QUESTION 3

22

Problem

A 6.0 V lamp requires 80 mA and must operate from a 9.0 V source. A resistor is placed in series with the lamp. Find the ideal resistor value and its power dissipation. Then select a practical resistor value and a safe power rating.

Use the general equations first · Show every GUESS step · Keep units with values · Round only the final answer

23 of 25

Question 4 · Work backward from one voltage drop

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A · QUESTION 4

23

Problem

Three resistors are in series: R₁ = 6.8 kΩ, R₂ = 12 kΩ and R₃ = 24 kΩ. The measured drop across R₂ is 9.0 V. Find Iₜ, V₁, V₃ and Vₜ.

Use the general equations first · Show every GUESS step · Keep units with values · Round only the final answer

24 of 25

Question 5 · Power-rating challenge

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A · QUESTION 5

24

Problem

R₁ = 1.0 kΩ is rated 0.25 W and R₂ = 1.5 kΩ is rated 0.125 W. They are connected in series. Find the largest source voltage that keeps both resistors within their ratings. Identify which resistor sets the limit.

Use the general equations first · Show every GUESS step · Keep units with values · Round only the final answer

25 of 25

Sources and support

CC BY-SA 4.0 · TECHNOLOGY COMMONS · SERIES A

25

Chapter 4 · Series circuits

Chapter 4 · Worked and practice problems

Experiment 4-1 · Series circuits

Equations, units, prefixes and GUESS