1 of 21

2 of 21

SERVER

OCP NIC Community Update�November 2026

�����Sub-group Project Wiki: https://www.opencompute.org/wiki/Server/NIC�

Mailing List: https://ocp-all.groups.io/g/OCP-NIC

NIC3.0

3 of 21

Agenda

  • OCP Global Summit
  • Thermal Workstream
  • Spec 1.7.0 update

​

4 of 21

OCP Global Summit

  • “Scaling Innovation for the AI Era”
  • 15,000 attendees - Sold out
  • 38% increase from 2025 (10,835)
  • 22 tracks; 948 speakers; 578 sessions
  • 178 sponsors; 158 booths
  • All recorded content/slide decks are online:

​

​

​

​

  • 2027 OCP Global Summit
  • Moscone Center - San Francisco, CA.

​

5 of 21

OCP NIC 3.0 Updates

Breakout session:

  • Updates for PCIe Gen 7, and test fixtures
  • Systems management updates (FRU)
  • Liquid cooling reference design
  • Short term power transients
  • 200 W connectors (in active development)
  • Link: https://www.youtube.com/watch?v=eNAsQ-L88pw

​

Innovation village

  • Display text fixtures, cards and liquid cooling reference design

​

6 of 21

OCP NIC Thermal Workstream

  • Facilitated by Jason Rock: jason.rock@dell.com

​

  • Meetings have resumed

​

  • First meeting held: 10/6
    • Finalizing v1.7 inputs
    • Liquid cooling activities

7 of 21

Draft v1.7 Section 7.2.2 - TSFF - Hot Aisle

Thermal workstream contributed the TSFF Card ASIC cooling estimates for Hot Aisle operation.

​

​

8 of 21

Use cases

  • Form factors: SFF, TSFF, DSFF
  • Today OCP NIC spec focused on radiated / fan cooling
  • Liquid cooled systems exist today, desire for capturing heat from the NICs / optics with liquid
  • Brackets - vented, solid (solid brackets facilitate better liquid heat capture, reduce air convection)
  • Reason for liquid cooling is because of the recent high speed NICs because they are quite power hungry / high thermal
  • Because of the platform is moving beyond just cooling computational devices (ex CPUs) with liquid we’re starting to see the need for liquid cooling for Dimms, SDDs, etc. Fans take space in this rack - at what point is this still required?
  • Do we look at solution(s) that achieve 100% DLC system with both SFF & TSFF?
  • What about the DSFF? Where does that play, is there a need?

​

Everything we are working on is tied to thermal performance / relief

Thermal Workstream Objectives and Scope

9 of 21

Proposal to add TA-1037 achieve up to 200 W

  • Why:
    • NICs/add-in-cards power demands are increasing
    • 80 W was enough for our traditional NICs
    • Power delivery is limited by the TA-1002 connector
  • Need:
    • Higher power connector
    • Backwards compatibility with existing OCP NIC cards.
    • “SFF-TA-1037 4C+ EP” connector as used on the PMM
      • HB thicknesses 1.57 mm to 3.05 mm ← need HB thickness aligned w/ SFF-TA-1002.
      • AIC thickness 1.57 mm
  • What needs to be investigated:
    • Should we add this? (both SFF and TSFF?)
    • System level interoperability implications from a thermal cooling standpoint
    • Couple liquid cooling implementations

​

10 of 21

OCP NIC use cases based on FF

SFF

  • Removable LOM
  • BaseT 10M -10G
  • SFP 1G, 10G, 25G, 100G
  • QSFP 100G, 200G, 400G

​

Multiple use cases

​

Tend to use standard HPMs

TSFF

  • Greater thermal relief
  • QSFP 400G & OSFP 400G / 800G / 1.6Tbps
  • Support SAS

​

Vertical, vendor specific, xPU-based / use cases

Tend to be custom/bespoke

11 of 21

  • Today liquid cooling with AI xPUs is prevalent

​

  • Seeing need for cooling other devices with liquid as fan area can be replaced by a total system manifold

​

  • How do we enable OCP NICs to to be connected in a liquid-cooled (no Fan) chassis manifold?

​

  • Should we also investigate/define SFF-based systems moving to all liquid cooling, too?

Major focus is / has been AI rackscale solutions

How we see liquid cooling in a rack shelf

AI xPU

nodes

Manifold

other devices

NICs, Dimms,

SDDs

12 of 21

Liquid Cooled TSFF Keep-in zone discussion

​

Intent is for System vendor and/or NIC vendor that yet to investigate into liquid cooling to have a reference design submitted by multiple member companies

LC Design by Meta/Boyd, et al.

13 of 21

Spec Draft 1.6.2 (for 1.7.0)

  • Add DSP0220 FRU requirements
  • PCIe Gen 7 insertion loss limits
  • SFF-TA-1002 short term power excursions >80W
  • Thermal workstream contributions for TSFF

​

Draft will be posted on the OCP NIC web page.

Notice will be sent to the OCP NIC Groups.io reflector.

14 of 21

DSP0220 “hybrid” FRU format

  • IPMI Mfg Date/Time Field
    • Rolls over to 00_00_01h for cards manufactured after Nov 24 ‘27)
    • Set to 00_00_00h

​

  • Add 0xC0 DMTF OEM Record
    • DMTF IANA - 3 bytes
    • DMTF FRU header offset from EEPROM address 0x00 (4 bytes)

15 of 21

IPMI FRU Mfg Date/Time Rollover

16 of 21

DSP0220 DSFF Example

17 of 21

DMTF FRU Files Record

18 of 21

​

Thank You

​

​

​

​

​

19 of 21

OCP Global Summit

Accepted Presentations

  • OCP NIC 2026: Gen 7 and liquid cooling – More speed and power ahead.
    • Jason Rock – Dell Technologies
    • Thomas Ng – Intel Corporation

Innovation Village

  • Focused on AI / Liquid cooling discussions and demo to help drive spec requirements
    • Broadcom Inc, Dell Technologies, Intel Corporation, Meta, Portwell
    • In the “IT Infra” area this year.
  • Intel/Thomas to lead planning activities

20 of 21

Draft Spec for 1.7.0

  • Opens:
    • DSP0220 (DMTF FRU) requirements text

​

  • Your feedback is welcomed!
  • The draft spec is available on the Wiki page: https://www.opencompute.org/wiki/Server/NIC
  • Scroll down to “Working Draft Docs”
  • Content review in November and submit to steering committee by end of Q4’2026

​

21 of 21

200 W power connector

  • SFF-TA-1037 (PMM) ⇒ 200W 4C+ EP connector
    • Backwards compatible with SFF-TA-1002 cards
    • Large Power / GND blade on NIC/connector
    • Requires updated platforms for high power cards

​

  • Configurations
    • Available in vertical, RA and straddle mount
    • Cabled / panel mount?
    • Gen 7 support?

​

  • Things to solve
    • Cooling
    • Preventing 200W card from plugging into legacy chassis.
    • Mechanical interlock - interference fit?
    • FRU - read power budget first? Hardware pin interlock?

Reference – Public SNIA document: https://members.snia.org/document/dl/51356