BRANCH AUTOMOBILE ENGINEERING

​

SEM 5^TH

​

SUBJECT AUTOMOTIVE TRANSMISSION

​

CHAPTER 05

​

TOPIC REAR AXLE

​

FACULTY Er. BALADHARA JENA

1.REAR AXLE

2.Forces on rear axle

3.Types of rear axle construction

4.Rear axle drives

5.Types of rear axle casing

6.FINAL DRIVE

7.Differential

8.Types of gears for final drive

9.PROPELLER SHAFT

10.Parts of propeller shaft

11. Improvements in transmission system

•_{Rear Axles are structural members on which}

Rear wheels are mounted on bearings.

•_{The weight of the body of the automobile and}

load due to the occupants is transmitted

through springs to the axle casing.

1.Weight of the Body

2.Driving thrust

3.Torque Reaction

4.Side thrust

•_{Rear axle behaves like a beam supported at}

the ends and loaded at two points.

•_{The load coming on the axle is due to the}

weight of the body being transmitted through

the suspension springs.

•_{Weight causes shear force and bending on the}

wheels.

•_{Torque produced by the engine causes the thrust}

on the wheels. This force is responsible for the

forward motion of the vehicle.

•_{The drive force from the wheels is transmitted to}

the body or chassis by means of Radius rods or

thrust members. These members are in

longitudinal direction connecting axle casing and

the body.

•_{Torque reaction occurs due to the resistance offered by the}

wheels to the motion. This causes a torque produced on the

axle in the counter clockwise direction when viewed from the

left side of the vehicle rear wheel axle.

•_{The torque produced by the braking torque is just the}

opposite to the torque reaction.

•_{The torque reaction is opposed by Panhard rod which}

connects the Rear axle to the vehicle body or chassis and

prevents excessive bending load coming onto the propeller

shaft.

•_{Side thrust comes mainly when the vehicle is}

taking a turn or when the vehicle is moving

along an laterally inclined surface.

•_{The side thrust coming on to the axle can be}

taken by Panhard rod.

•_{Shearing force due to vehicle weight}

•_{Bending moment due to the offset of the wheel}

and the suspension.

•_{End thrust due to the side forces due to cornering,}

side wind etc.

•_{Bending moment due to end thrust and reaction}

from the tires.

•_{Driving torque.}

•_{Semi floating axle}

•_{Full floating axle}

•_{Three quarter floating axle}

•_{The wheel hub is connected directly to the rear axle.}

•_{All the loads are taken by the rear axle (Shearing, Bending, End}

thrust, Driving torque and brake torque).

•_Advantages

• _{The semi floating axle is the simplest and cheapest and they are}

widely used in cars.

•_{Disadvantages}

• _{The axle has to be designed for carrying higher loads i.e. they}

are of higher diameter for the same torque transmitted by other types

of axle supporting.

•_{The wheels hubs are mounted directly onto the axle casing and are}

supported by two taper roller bearings.

•_{The load on the axle is very less. It need to take only the drive torque.}

•_Advantages

• _{These are very robust type and are used for heavy vehicles.}

• _{Axle shaft carry only the drive torque so their failure does not affect the}

vehicle wheels.

• _{Vehicle can be towed with the broken axle shaft.}

• _{Axle shaft can be replaced by without jacking.}

•_Disadvantage

• _{Costliest type of axle supporting.}

•_{The bearing is mounted between the axle and the axle casing.}

•_{The axle shaft has to take drive torque and the end loads.}

•_{The axle casing will take Bending an shearing forces.}

•_Advantages

• _{At one time this axle type was commonly used for cars and light}

commercial vehicles.

•_{Disadvantages}

• _{These axles are no longer preferred. instead semi floating axles}

are used.

1.Hotchkiss Drive

2.Torque tube drive

•_{Simplest and most widely used rear axle drive.}

•_{The suspension springs take torque reaction driving thrust and side thrust}

•_Construction

•_{Propeller shaft with two universal joints and a sliding joint. The spring is fixed rigidly}

in the middle onto the frame. The drive torque is transmitted through the front half of

the springs.

•_{The front end of the leaf suspension is rigidly fixed onto the frame while the rear is}

connected via a shackle.

•_{Two universal joints are used to avoid the bending of the propeller shaft due to the}

torque reaction.

•_{Sliding joint is provided to accommodate for the variation of the length in the}

transmission shaft.

•_{Torque reaction, Braking torque and drive thrust are taken by Torque tube.}

•_{The suspension springs are taking only the side thrust and body weight.}

•_Construction

•_{One end of the torque tube is attached to the axle casing while the other}

end is spherical and fits into the cup on the frame. The torque tube

encloses the propeller shaft.

•_{Torque tube takes the torque reaction and centre line of the bevel pinion}

shaft always passes through the centre of the spherical cup.

•_{Single universal joint is used in the transmission drive because the}

universal joint is situated exactly at the centre of the spherical cup.

•_{No sliding joint is provided since the pinion shaft and the propeller shaft}

moves same center ( spherical cup).

1.Split type.

2.Banjo or Separate carrier type.

3.Salisbury or Integral Carrier type.

•_{The axle casing is made in two halves and then}

bolted together for assembly. But the main

disadvantage is whole rear axle has to be

removed as a unit and reassembled in case of

a fault. This kind is no longer used now.

•_{Axle is made as a single piece The complete}

differential unit is separate unit and is bolted to

the axle casing and the two shafts are put from

two sides.

•_{In case of repair the shafts can be taken from}

two sides and differential can be removed

easily.

•_{This is similar to the banjo type except that the}

permanent housing tubes are pressed and

welded onto the sides.

•_{This is the most commonly used kind of rear}

wheel driven cars.

•_{Final drive is used to provide a permamanent speed}

reduction and to turn the drive through 90 degree.

•_{The reduction ratio provided by the final drive is 4:1 for cars}

and 10:1 for heavy vehicles.

•_{The reduction ration upto 7:1 can be done in single stage}

and above that is done in two stages. This is done to reduce

the size of the gear and to improve the ground clearance.

•_{Final drive can be bevel pinion and crown wheel or worm and}

worm wheel arrangement.

1.Straight Bevel Gears.

2.Spiral Bevel Gears.

3.Hypoid Bevel Gears

4.Worm and Worm Wheel Arrangement.

•_{The gears have straight teeth.}

•_Advantages

•_{Simplest and Cheapest}

•_{Disadvantages}

•_{Uneven transmission due to contact of single}

pair of teeth.

•_{Less load carrying capacity.}

•_{Noisy and high levels of wear.}

•_{Spiral bevel gears have curved teeth so have}

greater number of teeth in contact. The gear

tooth have sliding motion also in between.

•_Advantages

•_{Silent Running.}

•_{They are able to take more loads.}

•_{The structure of the teeth have hyperboloid in shape. Hyperboloid is}

obtained by rotating a hyperbola Abut an offset axis.

•_{The gears transmit motion at right at right angles but the axis of the}

gears don’t intersect but they lie at an offset distance.

•_Advantages

•_{The hypoid gears permit a lower position of the propeller shaft and}

allow more lower chassis height or less chassis height as the case

may be.

• _{Hypoid gears increases the loads capacity of the gears.}

•_Disadvantage

•_{Expensive difficult to assemble and need special lubricant due to the}

greater sliding action between the gears.

•_{Worm is a single or multi started thread which drives the worm wheel which}

has teeth over the periphery of the wheel.

•_{Higher gear ratios are possible in worm and worm wheel arrangement.}

•_Advantages

•_{Worm and Worm wheel arrangement is particularly used in heavy vehicle}

where higher gear ratios of greater than 6 needed

•_{Strong and efficient drive}

•_{Single stage reduction is only necessary for higher gear ratios also.}

•_{Worm gears give low chassis height or more ground clearance as the case}

may be.

•_{Disadvantages}

•_{Higher cost and more weight than bevel gear}

•_{Mechanical efficiency is lower than bevel gear for single stage reduction}

•_{Lubrication is difficult with overhead worm.}

•_{Differential is the gear mechanism which}

allows the wheels to turn at different speeds

according to the radius of curvature they are

negotiating. The differential allows the wheels

to rotate at different speeds using planetary

gear mechanism and give different speeds

according to the load coming onto the different

wheels.

•_{Propeller shaft transmits the drive from the}

engine to the drive axles.

•_{Propeller shaft consists of three main parts}

1.Shaft

2.Universal joints

3.Slip joints

•_{Shaft is the member which transmits the power. It}

needs to withstand torsional loads mainly.

Normally the shafts are of tubular cross sections.

They needs to be well balanced to avoid whirling at

high speeds.

•_{Materials used for shafts are steel aluminum or}

composites materials.

•_{The mass of the shaft has to be made small to}

avoid high rotational moment of inertia which

decreases acceleration capabilities of the system.

•_{Universal joints are used to transmit power}

between inclined shafts.

•_{Different kinds of universal joints are}

•_{Hooks joint}

•_{Hooks joint with needle roller bearings}

•_{Perfect circle U joints}

•_{Flexible Ring universal joints}

•_{Rzepppa joint}

•_{Tripoid joint}

•_{Slip joint is provided to accommodate for the}

variations of the length of the propeller shaft.

This is necessary due to the relative

movements of the axle and the vehicle body

due to the suspension action.

•_{The slip joint is formed by internal splines on}

the sleeve and external splines on the propeller

shaft.