2 of 31

1) When climbing at a constant mach number below the tropopause through an inversion:
A) the CAS and TAS will both decrease.
B) the CAS will decrease and the TAS will increase.
C) the CAS will increase and the TAS will decrease.
D) the CAS and TAS will both increase.

2) Which instrument does not connect to the static system?
A) Vertical speed indicator.
B) Vacuum gauge.
C) Airspeed Indicator.
D) Altimeter.

3) The static pressure error of the static vent on which the altimeter is connected varies substantially with the:
A) Mach number of the aircraft.
B) static temperature.
C) aircraft altitude.
D) deformation of the aneroid capsule.

4) The primary factor which makes the servo-assisted altimeter more accurate than the simple pressure altimeter is the use of:
A) more effective temperature compensating leaf springs.
B) combination of counters/pointers.
C) an induction pick-off device.
D) a sub-scale logarithmic function.

5) Cruising at FL390, M.84 is found to give a TAS of 499kt. The ISA deviation at this level will be:
A) +19.
B) -19.
C) -17.
D) +17.

3 of 31

6) Compressibility error in the ASI is normally corrected by:
A) Accurate calibration of the instrument
B) Use of the navigation computer
C) Use of a calibration card placed next to the instrument
D) The error is insignificant and can be ignored

7) The altitude indicated on board an aircraft flying in an atmosphere where all atmosphere layers below the aircraft are warm is:
A) the same as the real altitude
B) higher than the real altitude
C) lower than the real altitude
D) equal to the standard altitude

8) An aircraft is flying at an TAS of 310 Kt at FL290, temperature deviation is -6º C. The local speed of sound is:
A) 563 Kt.
B) 583 Kt.
C) 596 Kt.
D) 570 Kt.

9) What will the altimeter of an aircraft on the aerodrome indicate with QNH set on the subscale?
A) The equivalent sea level pressure at the airfield.
B) The airfield barometric pressure.
C) Airfield elevation.
D) Zero.
10) The reason for the adjustable index on the Machmeter being set at a different Mach number on different aircraft types is:
A) to correct for the differing instrument errors
B) to indicate the best cruising Mach number for that aircraft
C) because different aircraft types have different critical Mach numbers
D) to correct for the differing position errors

4 of 31

11) During a missed approach and go-around procedure the change of aircraft attitude plus raising of the landing gear and changing of flap settings can cause short term unpredictable errors in certain instruments. The instruments most likely to be affected in this case are:
A) the airspeed indicator, machmeter and vertical speed indicator.
B) the vertical speed indicator, airspeed indicator and altimeter.
C) the altimeter, artificial horizon and vertical speed indicator.
D) the machmeter, airspeed indicator, altimeter and vertical speed indicator.
12) Turbulent flow around a pressure head will cause:
A) an increase in the dynamic pressure.
B) approximately 95% of the position error.
C) 95% increase in manoeuvre induced error.
D) density error.
13) Dynamic pressure is given by:
A) The static energy formula: ½ density x V2
B) The static energy formula P1V1 = P2V2
C) The kinetic energy formula: ½ density x V2
D) The kinetic energy formula P1V1 = P2V2

14) An aircraft flying at Mach 0.83 is in air SAT 230 Kelvin. What is the TAS?
A) 495 kt
B) 490 kt
C) 575 kt
D) 470 kt
15) The advantages of an ADC over a traditional pitot - static system are:
position and compressibility correction.
reduced lag
ability to supply many instruments
ability to act as an altimeter following failure.
A) 2, 3 & 4
B) 1, 3 & 4
C) 1, 2 & 3
D) 1, 2 & 4

5 of 31

16) When the barometric subscale of the altimeter is adjusted to 1013.2 hPa, what type of altitude is being measured?
A) True altitude.
B) Indicated altitude.
C) Pressure altitude.
D) Relative height.
17) A servo altimeter has a quoted accuracy of 1 mb at mean sea level. The accuracy in the standard atmosphere is:
A) ± 30 ft at 20 000 ft and ± 100 ft at 20 000 ft
B) ± 27 ft at MSL and ± 50 ft at 10 000 ft
C) ± 50 ft at 10 000 ft and ± 100 ft at 40 000 ft
D) ± 50 ft at 20 000 ft and ± 90 ft at the tropopause

18) VNO is the maximum speed:
A) not to be exceeded except in still air and with caution.
B) with flaps extended in landing position.
C) at which the flight controls can be fully deflected.
D) which must never be exceeded.

19) An is aircraft flying at a TAS of 1100 knots at FL 650. A change in 0.1M causes a change in TAS of 57 knots.�The temperature deviation at FL 650 assuming an ISA atmosphere is:
A) +5
B) -5
C) +2.5
D) -2.5

20) The advantages provided by an air data computer to indicate the altitude are:
Position/pressure error correction
Hysteresis error correction
Remote data transmission capability
Capability of operating as a conventional altimeter in the event of a failure
The combination of correct statements is:
A) 1,2,3,4
B) 1,3,4
C) 2,3,4
D) 1,2,3

6 of 31

21) An aircraft is passing 6,500 ft in a descent when the static line becomes blocked. The altimeter then reads:
A) zero
B) less than 6,500 ft
C) more than 6,500 ft
D) 6,500 ft
22) Considering the maximum operational Mach number (MMO) and the maximum operational speed (VMO), the captain of a pressurized aircraft begins his descent from a high flight level. In order to meet his scheduled time of arrival, he decides to use the maximum ground speed at any time of the descent. He will be limited :
A) by the MMO
B) initially by the VMO, then by the MMO below a certain flight level
C) initially by the MMO, then by the VMO below a certain flight level
D) by the VMO in still air
23) How many diaphragms are present in a basic Mach meter?
A) Four.
B) Three.
C) One.
D) Two.
24) The atmospheric pressure at FL 70 in a " standard + 10" atmosphere is:
A) 781.85 hPa
B) 1013.25 hPa
C) 942.85 hPa
D) 644.41 hPa
25) During a climb after take-off from a contaminated runway, if the total pressure probe of the airspeed indicator is blocked, the pilot finds that indicated airspeed :
A) increases abruptly towards VNE
B) decreases steadily
C) increases steadily
D) decreases, abruptly towards zero

7 of 31

26) Pressure error consists of which of the following:
A) Configuration change, manoeuvre induced errors, turbulence
B) Slipstream error, manoeuvre induced errors, turbulence
C) Configuration change, profile induced errors, turbulence
D) Configuration change, manoeuvre induced errors, slipstream
27) The purpose of the IVSI is to:
A) indicate to the pilot instantaneously when an aircraft pitches in turn, especially steep turns.
B) give an instantaneous indication of the aircraft's vertical speed when a climb or descent has been initiated.
C) automatically initiate climbs and descents through the automatic flight control system.
D) eliminate lag by passing static pressure directly into the case before entering the metering device.
28) On board an aircraft the altitude is measured from the:
A) pressure altitude.
B) standard altitude.
C) temperature altitude.
D) density altitude.

29) When an altimeter is used for SSR it is always referenced to:
A) QFE
B) The pressure setting in use
C) QNH
D) 1013.25 hPa

30) The pressure measured at the forward facing orifice of a pitot tube is the:
A) total pressure.
B) total pressure plus static pressure.
C) static pressure.
D) dynamic pressure.

8 of 31

31) Indication of Mach number is obtained from:
A) Indicated speed and altitude using a speed indicator equipped with an altimeter type aneroid.
B) Indicated speed (IAS) compared with true air speed (TAS) from the air data computer.
C) A kind of echo sound comparing velocity of sound with indicated speed.
D) An ordinary airspeed indicator scaled for Mach numbers instead of knots.
32) When descending through an isothermal layer at a constant Calibrated Airspeed (CAS), the True Airspeed (TAS) will:
A) remain constant.
B) decrease.
C) increase at an exponential rate.
D) increase at a linear rate.
33) Aircraft with pressurized cabin in flight:�When switching to the alternate static pressure source, the pointer of the Vertical Speed Indicator:
A) indicates a descent, then settles down and reads incorrectly
B) indicates a slight continuous descent
C) indicates a climb, then settles down and reads incorrectly
D) indicates correctly

34) The subscale of an altimeter is set to 1030 mb and indicates 4500 ft when the QNH is 996 mb. Assuming 1 mb equals 30 ft, the true height of the aircraft AMSL is:
A) 3480 ft
B) 3990 ft
C) 3180 ft
D) 5520 ft

35) The errors to which the machmeter is subject are:
A) instrument error, position error, compressibility error and manoeuvre induced error.
B) instrument error, position error.
C) instrument error, position error, barometric error, temperature error and manoeuvre induced error.
D) instrument error, position error, density error and manoeuvre induced error.

9 of 31

36) Pressure error in an altimeter arises because:
A) The true external kinetic pressure is not accurately transmitted to the instrument
B) The true external static pressure is not accurately transmitted to the instrument
C) The true external dynamic pressure is not accurately transmitted to the instrument
D) The true external pitot pressure is not accurately transmitted to the instrument

37) The airspeed indicator is calibrated to:
A) the full ISA
B) ISA at 36,000 ft
C) ISA at mean sea level
D) ISA at the height the aircraft is flying

38) An increase of 0.15 in Mach number results in an increase of 93 kt in TAS. If the temperature deviation from ISA is +9° C, the FL is:
A) FL 170
B) FL 200
C) FL 220
D) FL 90

39) The QNH is by definition the value of the:
A) atmospheric pressure at the sea level of the location for which it is given.
B) altimeter setting so that the needles indicate zero when the aircraft is on ground at the location for which it is provided.
C) altimeter setting so that the needles of the altimeter indicate the altitude of the location for which it is given.
D) atmospheric pressure at the level of the ground over flown by the aircraft.

40) Given:��M: Mach number�Ts: static temperature�Tt: total temperature��Which of the following statements is correct?
A) Ts = Tt x (1+0.2M²)
B) Ts = Tt / (1+0.2M²)
C) Ts = Tt x (0.2M²)
D) Ts = Tt / (0.2M²)

10 of 31

41) As an airplane climbs higher, the true airspeed for a given indicated airspeed will:
A) Remain the same
B) Vary depending on the actual value of the indicated airspeed and the angle of attack
C) Increase
D) Decrease

42) If the pitot line to an ASI becomes totally blocked during a climb, the ASI reading will:
A) progressively increase.
B) drop to zero.
C) progressively decrease.
D) remain unchanged.

43) What is the significance of the yellow arc in an airspeed indicator?
A) Never exceed range
B) Turbulent operations range
C) Normal operating range
D) Structural warning range

44) Which of the following instruments require pitot and static pressure inputs?
A) Airspeed indicator only.
B) Airspeed indicator, vertical speed indicator, altimeter.
C) Airspeed indicator, machmeter and vertical speed indicator.
D) Airspeed indicator and machmeter.

45) At a constant calibrated airspeed (CAS), the Mach number:
A) decreases when the altitude increases.
B) increases when the altitude increases.
C) remains unchanged when the outside temperature increases.
D) remains unchanged when the outside temperature decreases.

11 of 31

46) Which of the following could cause a pressure (position) error:
Changes in configuration
Manoeuvres
Turbulence
A) 2 and 3 are correct
B) All the statements are correct
C) 1 and 3 are correct
D) 1 and 2 are correct
47) With a constant weight, irrespective of the airfield altitude, an aircraft always takes off at the same:
A) ground speed.
B) equivalent airspeed.
C) calibrated airspeed.
D) true airspeed.

48) An aircraft is flying straight and level, over a warm air mass. The altimeter reading will be:
A) less than the real height
B) correct
C) greater than the real height
D) oscillating around the correct height

49) The reading of a Mach indicator is independent of:
A) the static pressure.
B) the outside temperature.
C) the total pressure.
D) the differential pressure measurement.
50) The airspeed indicator of an aircraft is provided with a moving red and white hatched pointer. This pointer indicates the:
A) speed indicated on the autothrottle control box, versus temperature.
B) speed indicated on the autothrottle control box versus altitude.
C) maximum speed in VMO operation, versus temperature.
D) maximum speed in VMO operation versus altitude.

12 of 31

51) VLE is the maximum:
A) speed authorized in flight.
B) speed with flaps extended in a given position.
C) flight speed with landing gear down.
D) speed at which the landing gear can be operated with full safety.

52) An aircraft is flying at M0.86 at FL320. The temperature deviation is +10° C. The TAS is:
A) 522 kts
B) 512 kts
C) 481 kts
D) 607 kts

53) The difference between static air temperature and total air temperature is known as:
A) the recovery factor
B) corrected outside air temperature
C) hot ramp radiation
D) the ram rise
54) If the alternate static source is used, the resulting reading will be:
A) Too low reading of altitude.
B) Too high reading of altitude.
C) Too low reading of airspeed.
D) No reading of airspeed.
55) When flying from a sector of warm air into one of colder air, the altimeter will:
A) underread.
B) show the actual height above ground.
C) overread.
D) be just as correct as before.

13 of 31

56) Today's airspeed indicators (calibrated to the Saint-Venant formula), indicate, in the absence of static (and instrumental) error:
A) The calibrated airspeed (CAS) in all cases
B) The true airspeed
C) The airspeed, whatever the altitude
D) The equivalent airspeed, in all cases

57) When descending through an isothermal level (at a constant Mach number) the TAS will .... (i), the CAS .... (ii) and the LSS will .... (iii):
A) i remain constant ii increase iii remain constant
B) i decrease ii decrease iii remain constant
C) i increase ii increase iii decrease
D) i remain constant ii decrease iii increase

58) A pitot tube measures:
A) Dynamic minus static pressure
B) Static pressure
C) Dynamic plus static pressure
D) Dynamic pressure

59) An aircraft is flying at 0.86 M, temperature 218 Kelvin. The TAS is:
A) 477 kt
B) 607 kt
C) 494 kt
D) 575 kt

60) An aircraft flies from A to B with QNH at A of 1019mb set on the altimeter subscale throughout the flight.�Assuming all other errors are zero and that 1 mb = 30 feet, when overhead B, QNH 1013 mbs, the altimeter will be:
A) over indicating by 120 feet
B) indicating true altitude
C) under indicating by 180 feet
D) over indicating by 180 feet

14 of 31

61) If the static line to the ASI becomes blocked during a climb, the ASI reading will:
A) remain fixed.
B) increase, no matter what the actual airspeed is.
C) progressively underread.
D) progressively overread.

62) Indicated airspeed (as read on the airspeed indicator] will:
A) Increase in tailwind.
B) Remain unchanged in headwind and tailwind.
C) Increase in headwind.
D) Decrease in tailwind.

63) An aircraft is flying at FL 390, temperature -56.5° C at Mach 0.85. The TAS of the aircraft is:
A) 485
B) 561
C) 472
D) 476

64) The colour arcs of an ASI are in ascending speed order?
A) white, green and yellow
B) blue, yellow and red
C) white, yellow and red
D) green, yellow and red

65) The velocity maximum operating (V.M.O.) is a speed expressed in:
A) equivalent airspeed (EAS).
B) calibrated airspeed (CAS).
C) true airspeed (TAS).
D) computed airspeed (COAS).

15 of 31

66) When side-slipping, one of the instruments below will give an incorrect indication:
A) Altitude Indicator.
B) Attitude Indicator.
C) Airspeed Indicator.
D) Vertical Speed Indicator.

67) Sound propagates through the air at a speed which only depends on:
A) density.
B) pressure.
C) temperature and the pressure.
D) temperature.

68) A pitot blockage of both the ram air input and the drain hole with the static port open causes the airspeed indicator to:
A) read a little low.
B) read a little high.
C) react like an altimeter.
D) freeze at zero.

69) A pressure head is subject to the following errors:
A) position, manoeuvre induced and temperature errors.
B) position, manoeuvre induced and density errors.
C) position and manoeuvre induced errors.
D) position, manoeuvre induced and instrument errors.
70) The limits of the white scale of an airspeed indicator are:
A) VS1 for the lower limit and VFE for the upper limit
B) VS1 for the lower limit and VLE for the upper limit
C) VSO for the lower limit and VFE for the upper limit
D) VSO for the lower limit and VLE for the upper limit

16 of 31

71) If the outside temperature at 35 000 feet is -40° C, the local speed of sound is:
A) 686 kt.
B) 247 kt.
C) 596 kt.
D) 307 kt.

72) (Refer to figure 022-31)
�The altimeter in the attached figure shows:
A) FL 270
B) FL 27
C) a pressure altitude of 20700 ft
D) a height of 2700 ft
73) In a combined mach/airspeed indicator the purposes of the BARBER POLE is to indicate:
A) The maximum safe airspeed with flaps/slats extended
B) VMO and this value decreases at high altitudes
C) VMO and this value increases at high altitudes
D) VMO and this is a fixed value at all altitudes

74) An aircraft is flying at 4000 ft from a high temperature area to a cold temperature area where the temperature difference is 20º C. What will be the actual height of the aircraft:
A) 3840 ft
B) 4320 ft
C) 3680 ft
D) 4000 ft

75) If the ambient temperature decreases, the TAS of an aircraft cruising at a constant Mach number will:
A) remain constant.
B) decrease because local speed of sound decreases.
C) increase because local speed of sound increases.
D) increase because local speed of sound decreases.

17 of 31

76) A VSI metering unit incorporates a capillary tube to compensate for:
A) temperature and pressure changes with height
B) viscosity changes
C) position error
D) barometric error

77) The temperature at the airport is 23º C, what is the local speed of sound:
A) 616 knots
B) 644 knots
C) 694 knots
D) 671 knots

78) What does a vertical speed indicator actually measure?
A) The rate of pressure change.
B) The rate of temperature and altitude change.
C) The rate of altitude change.
D) The rate of temperature change.

79) VSO is shown on an ASI by a:
A) Red radial line
B) White arc
C) Yellow arc
D) Green arc

80) An aircraft is flying at FL 290, TAS 500 knots, 0.86M, the temperature deviation is:
A) -15
B) +25
C) +7
D) -8

18 of 31

81) Where a M/IAS indicator is being used:
A) At high altitudes, the VMO pointer retains a fixed position which indicates the maximum operating IAS permitted
B) At high altitudes, the VMO pointer retains a fixed position which indicates the maximum operating Mach Number permitted
C) At low altitudes, the VMO pointer retains a fixed position which indicates the maximum operating IAS permitted
D) At low altitudes, the VMO pointer retains a fixed position which indicates the maximum operating Mach
Number permitted
82) EAS is:
A) IAS corrected for compressibility
B) CAS corrected for position error
C) IAS corrected for instrument error only
D) CAS corrected for compressibility

83) For an altimeter, pressure fluctuations at the static vent cause:
A) Position error
B) Barometric error
C) Hysteresis error
D) Temperature error

84) The combined Machmeter / ASI is subject to the following errors:
A) instrument and compressibility only
B) position, density, instrument, compressibility, manoeuvre induced
C) instrument, pressure and temperature only
D) those of the Machmeter only

85) The machmeter employs:
A) Two capsules with their axes linked
B) Two capsules
C) Two capsules with their axes at 90° to each other
D) A capsule linked to a dashpot

19 of 31

86) The response time of a vertical speed detector may be increased by adding a:
A) return spring.
B) bimetallic strip.
C) second calibrated port.
D) correction based on an accelerometer sensor.
87) In the IVSI, lag error:
A) is eliminated by feeding a sample of static pressure to the case and delaying it to the capsule.
B) is virtually eliminated by using a special dashpot accelerometer assembly.
C) is only eliminated when initiating a climb or descent.
D) is eliminated by the use of logarithmic presentation.

88) Which of the following lists the errors of the machmeter?
A) Compressibility, position, density, instrument and manoeuvre induced
B) Lag, position, density, compressibility and temperature
C) Position, manoeuvre induced and instrument
D) Position, manoeuvre induced, lag, density and instrument

89) A pitot tube covered by ice which blocks the ram air inlet will affect the following instrument (s):
A) vertical speed indicator only.
B) altimeter only.
C) airspeed indicator only.
D) airspeed indicator, altimeter and vertical speed indicator.

90) If an aircraft is equipped with one altimeter which is compensated for position error and another altimeter which is not, and all other factors being equal:
A) ATC will get an erroneous altitude report SSR.
B) there will be no difference between them if air the data computer is functioning normally.
C) At high speed the non compensated altimeter will indicate a lower altitude.
D) at high speed, the non compensated altimeter will indicate a higher altitude.

20 of 31

91) A temperature sensor having a recovery factor of 0.75 indicates 30° C. Static Air Temperature (SAT) is 25° C.�How high is the Ram-rise?
A) 6.7° C.
B) 5° C.
C) 40° C.
D) 18.8° C.

92) When climbing at a constant Mach number below the tropopause, in ISA conditions, the Calibrated Airspeed (CAS) will:
A) remain constant.
B) increase at a linear rate.
C) decrease.
D) increase at an exponential rate.

93) An Air Data Computer (ADC):
A) Is an auxiliary system that provides altitude information in the event that the static source is blocked
B) Converts air data measurements given by ATC from the ground in order to provide correct altitude and speed information
C) Transforms air data measurements into electric impulses driving servo motors in instruments
D) Measures position error in the static system and transmits this information to ATC to provide correct altitude reporting

94) What corrections must be applied to indicated airspeed to produce true airspeed?
A) Correction for heading and altitude.
B) Correction for wind and temperature.
C) Correction for altitude and temperature.
D) Correction for altitude and wind.
95) An increase of 0.15 Mach results in an increase of 93 kt TAS of an aircraft. The local speed of sound is:
A) 560 kt
B) 580 kt
C) 685 kt
D) 620 kt

21 of 31

96) An aircraft is in level flight at FL100 over a mountain range, which extends up to 2.400 metres AMSL. If the regional QNH is 998 hPa (use 30 ft/hPa), what is the approximate terrain clearance?
A) 7.869 feet.
B) 1.681 feet.
C) 2.581 feet.
D) 450 feet.

97) The Airspeed Indicator measures:
A) Static pressure changes
B) Differential pressure changes
C) Static pressure
D) Differential pressure

98) If the static source to an airspeed indicator (ASI) becomes blocked during a descent the instrument will:
A) continue to indicate the speed applicable to that at the time of the blockage.
B) read zero.
C) over-read.
D) under-read.
99) Match true airspeed (TAS) with the associated definition:
A) Calibrated airspeed corrected for altitude and non-standard temperature.
B) Indicated airspeed corrected for installation and instrument errors.
C) The airspeed you read directly from the airspeed indicator.
D) Actual speed of an aircraft over ground.

100) Compressibility is corrected for when obtaining:
A) CAS from IAS and the correction is normally subtractive
B) CAS from IAS and the correction can be either additive or subtractive
C) EAS from CAS and the correction is normally subtractive
D) EAS from CAS and the correction is always subtractive

22 of 31

101) An aircraft flies an altitude of 3500 feet from A, elevation 700 feet QNH 1015 mb to B, elevation 1120 feet QNH 992 mb. Assuming the altimeter sub-scale is not changed, the aircraft will arrive over B at a height of:
A) 3500 feet
B) 2670 feet
C) 1690 feet
D) 2810 feet

102) The Mach number is:
A) a direct function of temperature ; it varies in proportion to the square root of the absolute temperature.
B) the ratio of the indicated airspeed to the sonic velocity at the altitude considered.
C) the ratio of the aircraft true airspeed to the sonic velocity at the altitude considered.
D) the ratio of the aircraft conventional airspeed to the sonic velocity at the altitude considered.

103) In An Air Data Computer (ADC), aeroplane altitude is calculated from:
A) Measurement of elapsed time for a radio signal transmitted to the ground surface and back.
B) Measurement of absolute barometric pressure from a static source on the fuselage.
C) The difference between absolute and dynamic pressure at the fuselage.
D) Measurement of outside air temperature (OAT).

104) Calibrated air speed is:
A) IAS plus instrument error correction
B) IAS plus compressibility correction
C) IAS plus the pressure error
D) IAS plus density error correction

105) CAS is IAS corrected for:
A) position error and instrument error
B) compressibility.
C) density error.
D) temperature error.

23 of 31

106) Change of temperature as an aircraft climbs or descends:
A) has no effect on the VSI readings, as only static pressure is used in this instrument.
B) is compensated at the metering unit by means of a capillary and orifice.
C) must be corrected using a computer or correction tables.
D) will affect VSI readings whenever actual temperature lapse rate differs from the standard atmosphere temperature lapse rate.

107) If the alternate static source is selected, the greatest error in the machmeter will be:
A) density error
B) position error
C) manoeuvre induced error
D) lag

108) The restricted choke in the VSI:
A) compensates for changes in temperature and density only
B) creates a differential pressure between the capsule and the case as its main function
C) will prevent the instrument being damaged by high rates of climb and descent
D) compensates for time lag in the instrument

109) The error in altimeter readings caused by the variation of the static pressure near the source is known as:
A) barometric error.
B) hysteresis effect.
C) instrument error.
D) position pressure error.

110) Match indicated airspeed (IAS) with the associated definition:
A) Actual speed of an aircraft over the ground.
B) The airspeed you read directly from the airspeed indicator.
C) Indicated airspeed corrected for installation and instrument errors.
D) Calibrated airspeed corrected for altitude and non-standard temperature.

24 of 31

111) The ISA temperature and pressure for 18 000 ft are:
A) -20.7º C and 595.2 hPa respectively
B) -20.7º C and 506 hPa respectively
C) -12.7º C and 506 hPa respectively
D) -12.7º C and 595.2 hPa respectively

112) The principle of operation of a servo-assisted pressure altimeter is that:
A) static pressure enters an aneroid capsule causing it to expand
B) static and pitot pressure are compared with the resultant pressure being used to drive the counter and pointer system
C) static pressure is used in the same way as a simple altimeter except that several capsules are used
D) static pressure changes are converted via an E- and I-bar transducer into electrical signal which is used, via a follow-up system, to move a digital counter and pointer system
113) When flying from low pressure to high pressure, the barometric error of an altimeter will cause the instrument to:
A) indicate the true altitude.
B) overread the true altitude of the aircraft.
C) indicate a higher altitude than the correct one.
D) underread the true altitude of the aircraft.

114) In a non-pressurized aircraft, if one or several static pressure ports are damaged, there is an ultimate emergency means for restoring a practically correct static pressure intake:
A) slightly opening a window to restore the ambient pressure in the cabin
B) descending as much as possible in order to fly at a pressure as close to 1013.25 hPa as possible
C) calculating the ambient static pressure, allowing for the altitude and QNH and adjusting the instruments
D) breaking the rate-of-climb indicator glass window

115) The Total Air Temperature probe measures total temperature (TAT) by:�(SAT = Static Air Temperature)
A) TAT = SAT + kinetic heating.
B) TAT = SAT - heating due to compressibility.
C) TAT = SAT - kinetic heating.
D) TAT = SAT + heating due to compressibility.

25 of 31

116) The limits of the yellow scale of an airspeed indicator are:
A) VLE for the lower limit and VNE for the upper limit.
B) VNO for the lower limit and VNE for the upper limit.
C) VLO for the lower limit and VNE for the upper limit.
D) VFE for the lower limit and VNE for the upper limit.

117) VFE is the maximum speed:
A) at which the flaps can be operated in turbulence.
B) with the flaps extended in take-off position.
C) with the flaps extended in landing position.
D) with the flaps extended in a given position.
118) Compared to the VSI what errors are eliminated by the IVSI?
A) turning
B) pressure
C) lag
D) temperature

119) The possibility of ingress of moisture to the instruments:
A) is prevented by the anti-icing heaters
B) is prevented by fitting blanks
C) is prevented by drain traps
D) is prevented by having the pitot head and static vents lower than the instruments

120) If the pitot tube is clogged, which instrument(s) is/are affected?
A) Altimeter only.
B) Vertical speed indicator only.
C) Altimeter and airspeed indicator.
D) Airspeed indicator only.

26 of 31

121) Select the correct statement:
A) CAS = TAS corrected for density error
B) EAS = IAS corrected for position error
C) TAS = EAS corrected for compressibility error
D) EAS = CAS corrected for compressibility error

122) We are maintaining a constant flight level. That means:
A) the outside air pressure is constant if the temperature remains constant.
B) the altitude above sea level is constant.
C) the outside air pressure is constant.
D) the altitude is constant when the sea-level pressure is constant.

123) The vertical speed indicator indications may be in error for some seconds after starting or finishing a climb or descent. The error is a result of:
A) a combination of position error and manoeuvre induced errors.
B) a combination of time lag and manoeuvre induced errors.
C) a combination of time lag and instrument error.
D) manoeuvre induced errors only.
124) Which statement is correct for the Vertical Speed Indicator (VSI) during a climb:
A) The pressure inside the capsule drops faster than the pressure outside the case
B) The pressure inside the capsule drops slower than the pressure inside the case
C) The pressure outside the capsule drops slower than the pressure inside the case
D) The pressure inside the capsule drops faster than the pressure inside the case

125) During a steady climb the pitot head becomes totally blocked by ice. As the climb continues the indications of the machmeter will:
A) stick at the Mach number at the time of blockage
B) progressively under indicate the Mach number
C) increase no matter what the actual Mach number
D) go to zero and stay there

27 of 31

126) The purpose of the vibrating device of an altimeter is to:
A) inform the crew of a failure of the instrument.
B) reduce the hysteresis effect.
C) reduce the effect of friction in the linkages.
D) allow damping of the measurement in the unit.

127) The vertical speed indicator of an aircraft flying at a true airspeed of 100 kt, in a descent with a slope of 3° indicates:
A) -50 ft/min
B) -500 ft/min
C) -150 ft/min
D) -300 ft/min

128) The mach number is the:
A) true airspeed (TAS) divided by the local speed of sound.
B) equivalent airspeed (EAS) divided by the local speed of sound.
C) corrected airspeed (CAS) divided by the local speed of sound.
D) indicated airspeed (IAS) divided by the local speed of sound.

129) Within a temperature range of +50° and -20° C the VSI is accurate to within limits of:
A) +/- 50 ft/min
B) +/- 200 ft/min
C) +/- 100 ft/min
D) +/- 250 ft/min

130) Density varies:
A) Directly with temperature and pressure
B) Inversely with temperature and pressure
C) Directly with pressure and inversely with temperature
D) Inversely with pressure and directly with temperature

28 of 31

131) The Mach number is a function of the:
A) relative air temperature.
B) humidity of the air.
C) Absolute temperature of the air.
D) Isobaric gradient of the fluid.

132) The reason for having a square-law compensation in the airspeed-indicator mechanism is:
A) The ram air pressure increases with the square-root of the airspeed
B) The differential pressure decreases with the square of the airspeed
C) The ram air pressure decreases with the square-root of the airspeed
D) The differential pressure increases with the square of the airspeed

133) VLO is the maximum:
A) flight speed with landing gear down.
B) speed with flaps extended in a given position.
C) cruising speed not to be exceeded except in still air with caution.
D) speed at which the landing gear can be operated with full safety.

134) Total Air Temp is always... than Static Air Temp and the difference varies with...
A) colder, altitude.
B) colder, CAS.
C) warmer, altitude.
D) warmer, TAS.

135) The hysteresis error of an altimeter varies substantially with the:
A) static temperature.
B) mach number of the aircraft.
C) time passed at a given altitude.
D) aircraft altitude.

29 of 31

136) The airspeed indicator circuit consists of pressure sensors. The pitot tube directly supplies:
A) the static pressure.
B) the dynamic pressure.
C) the total pressure.
D) the total pressure and the static pressure.

137) Indicated airspeed corrected for position error is:
A) Calibrated airspeed.
B) Equivalent air speed.
C) Ground speed.
D) True air speed.

138) If the static source of an altimeter becomes blocked during a descent the instrument will:
A) continue to display the reading at which the blockage occurred.
B) under-read.
C) indicate a height equivalent to the setting on the millibars subscale.
D) gradually indicate zero.

139) The vertical speed indicator VSI is fed by:
A) total pressure.
B) static pressure.
C) dynamic pressure.
D) differential pressure.

140) Given:
Ts: the static air temperature (SAT)
Tt: the total air temperature (TAT)
Kr: the recovery coefficient
M: the Mach number
The total temperature can be expressed by the formula:
A) Tt = Ts/(1+0.2 x Kr x M²)
B) Tt = Ts(1+0.2 x M²)
C) Tt = Ts(1-0.2 x M²)
D) Tt = Ts(1+0.2 x Kr x M²)

30 of 31

141) The full International Standard Atmosphere (ISA) is assumed in the calibration of:
A) the vertical speed indicator and the machmeter
B) the pressure altimeter and the airspeed indicator
C) the vertical speed indicator only
D) the pressure altimeter only

142) In a standard atmosphere and at the sea level, the calibrated airspeed (CAS) is:
A) higher than the true airspeed (TAS).
B) lower than the true airspeed (TAS).
C) independent of the true airspeed (TAS).
D) equal to the true airspeed (TAS).

143) Compressibility Error requires a .... (i) correction because it is .... (ii) of ....(iii) pressure. It gives .... (iv):
A) (i) positive (ii) a decrease (iii) static (iv) TAS
B) (I) negative (ii) a decrease (iii) static (iv) EAS
C) (i) positive (ii) an increase (iii) dynamic (iv) TAS
D) (i) negative (ii) an increase (iii) dynamic (iv) EAS

144) The IVSI is less reliable than the VSI when:
A) Overshooting
B) Pulling G
C) Both b and c
D) At an angle of bank of 55°

145) The servo altimeter is better than a sensitive altimeter because:
A) It improves high altitude error
B) It improves barometric error
C) All the above are correct
D) It improves temperature error

31 of 31

146) The operating principle of the vertical speed indicator (VSI) is based on the measurement of the rate of change of:
A) Static pressure.
B) Kinetic pressure.
C) Total pressure.
D) Dynamic pressure.

147) During a straight and uniform climb, the pilot maintains a constant calibrated airspeed (CAS):
A) The Mach number is constant and the true airspeed (TAS) decreases.
B) The Mach number increases and the true airspeed (TAS) is constant.
C) The Mach number increases and the true airspeed (TAS) increases.
D) The Mach number is constant and the true airspeed (TAS) is constant.

148) Dynamic pressure is:
A) Pitot pressure minus static pressure
B) Static pressure minus pitot pressure
C) Pitot pressure plus static pressure
D) Density and static pressure

149) If the static vent becomes blocked during climb:
A) the VSI will indicate an increasing rate of climb.
B) the VSI will stop at the rate of climb of the aircraft at the time of blockage.
C) the VSI will indicate a decreasing rate of climb.
D) the VSI will return to zero.

150) The limits of the green scale of an airspeed indicator are:
A) VS1 for the lower limit and VLO for the upper limit.
B) VS0 for the lower limit and VNO for the upper limit.
C) VS1 for the lower limit and VNE for the upper limit.
D) VS1 for the lower limit and VNO for the upper limit.