1 of 16

Agricultural Automation

Project By : Diwakar V

Athri Kumar S A

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

​

2 of 16

AIM OF THE PROJECT

To automatically maintain crop favorable environment(soil moisture) in an agricultural field.

​

3 of 16

INTRODUCTION: -

  • A selected crop requires a specified soil moisture ( X °C temperature and Y % humidity ) for its normal growth and yield. The present project is designed to maintain the favorable soil moisture congenial for selected crop.

4 of 16

COMPONENTS :-�

  • Temperature and Humidity sensor
  • Rain sensor
  • Soil Moisture sensor
  • Electronic Relay
  • Node MCU Board
  • LCD display
  • Server Provider ( Android Device )
  • Connecting wires

5 of 16

NODE MCU BOARD: �

  • NodeMCU is an open source IoT platform. It includes firmware which runs on the ESP8266 Wi-Fi SoC from Espressif, and hardware which is based on the ESP-12 module. The term "NodeMCU" by default refers to the firmware rather than the dev kits. The firmware uses the Lua scripting language. It is based on the eLua project, and built on the Espressif Non-OS SDK for ESP8266. It uses many open source projects, such as lua-cjson,and spiffs.

​

6 of 16

NODE MCU BOARD: �

7 of 16

ELECTRONIC RELAY: �

  • A relay is an electrically operated switch. Many relays use an electromagnet to mechanically operate a switch, but other operating principles are also used, such as solid state relay. Relays are used where it is necessary to control a circuit by a separate low-power signal, or where several circuits must be controlled by one signal.

​

8 of 16

TEMPERATURE AND HUMIDITY SENSOR

  • The DHT11 sensor consist of a humidity sensing component, a NTC temperature sensor (or thermistor) and an IC on the back side of the sensor.
  • For measuring humidity they use the humidity sensing component which has two electrodes with moisture holding substrate between them. So as the humidity changes, the conductivity of the substrate
  • changes or the resistance between these electrodes changes. This change in resistance is measured and processed by the IC which makes it ready to be read by a microcontroller.
  • On the other hand, for measuring temperature these sensors use a NTC temperature sensor or a thermistor. A thermistor is actually a variable resistor that changes its resistance with change of the temperature. These sensors are made by sintering of semi conductive materials such as ceramics or polymers in order to provide larger changes in the resistance with just small changes in temperature.

​

9 of 16

TEMPERATURE AND HUMIDITY SENSOR

10 of 16

SOIL MOISTURE SENSOR: �

  • Soil moisture sensors measure the volumetric water content in soil. Since the direct gravimetric measurement of free soil moisture requires removing, drying, and weighting of a sample, soil moisture sensors measure the volumetric water content indirectly by using some other property of the soil, such as electrical resistance, dielectric constant, or interaction with neutron , as a proxy for the moisture content.

​

11 of 16

SOIL MOISTURE SENSOR

12 of 16

RAIN SENSOR: �

  • A rain sensor or rain switch is a switching device activated by rainfall. The principle of operation is based on the capacitive principle, by which rain drops accumulated on the sensor’s surface change the electrical capacity of the sensor

13 of 16

BRIEF PROCEDURE:- � �

  • The soil moisture requirement of a crop is set in the code and is loaded to the node mcu. when the moisture content in the soil is less than the requirement then a signal is generated by the Sensor which in turn activates the motor. And if the moisture content in the soil is greater than the requirement then a signal is generated by the Sensor which in turn deactivates the motor(used to irrigate the crop field).

  • During this period of motor being ON, if precipitation (rain fall) happens this would cease the motor action which helps to conserve water. The motor supplies water to crop field until the favourable soil moisture requirement is attained.
  • The above logic is run continuously to maintain the required environment condition in a agricultural field.

​

14 of 16

15 of 16

APPLICATION: - �

•This project will help to reduce the work of farmers to maintain the crops for better yield.

•It will also help the farmers to combat the temperature and humidity variations [with respect to rainfall] in the environment.

•This also in a way helps in conservation of Water resource.

16 of 16

THANK YOU