1 of 20

Assembly Production Series

Lesson 3: Introduction to Motion

FRC 2587 The Discobots

Westside Division

2 of 20

Introduction

  • Having the various parts and assemblies of a robot is not very useful in itself
  • In order to score points, the robot must be able to create motion in one way or another
  • Motion is the general goal of Robotics and what all components of the robot is going towards directly or indirectly
  • Today, we’ll start from the power source and go towards the end result

3 of 20

Motors

  • Electric Machine that converts electrical energy to mechanical energy
  • Types of Motors
    • NEO 550
    • 775pro
    • CIM
    • NEO
    • Falcon 500

4 of 20

Part that we care about (for now)

  • Output shaft
    • How motion is transferred out of the motor
    • CIM/NEO - 8mm keyed
    • Falcon - spline
    • NEO 550 - ⅛”
    • 775 - 5mm

5 of 20

Free Speeds and Torque Rating

  • Different motors have different free speeds and torque ratings
  • Too advanced for us, right now, people will learn as needed
  • Refer to electronics lesson for more comprehensive view on motors (still need to make)

6 of 20

Gearboxes/Geartrains

  • Motor output shaft spins far too fast at too low of a torque rating
  • Gearboxes allow us to trade speed for strength
  • Pinion - first output from motor
  • Pinion Gear transfers power to gearbox

7 of 20

Planetary Gearboxes

  • Commonly used for everything that’s not a drivetrain
  • Uses pre-made stages
  • Load rating depends on the stage, do not exceed
  • VEX VersaPlanetary
  • REV MAXPlanetary and UltraPlanetary

8 of 20

Open Kit Geartrains

  • Must conform to Vendor specifications
  • Often has certain gears that have to be used
  • Fixed spacing for certain teeth #
  • Comes in various stages

9 of 20

Custom Gearboxes

  • Difficult to pull off
  • Uses 20dp gears for FRC
  • Consider type of shaft (½” hex, thunderhex or ⅜” hex)
  • Center to center distance must be exact
  • Distance based on teeth count
  • Can use pre-made sizing plate
  • Backlash

84 tooth 20dp spacing

10 of 20

Custom Gearboxes

  • Use WCP Calculator to calculate proper center-to-center distance
  • Extra center sometimes used to account for manufacturing tolerances

11 of 20

Shafts

  • Allows us to transfer motion in a concentric axis
  • Connects motion components through material by a hole

12 of 20

Shafts

  • ½” hex, ⅜” hex
    • Most common/FRC standard
    • Retained by shaft collars
  • ½” thunder/rounded hex
    • Rounded hex profile
    • Retained by bolt and washer or shaft collars
    • Has a through hole ready to be tapped
      • Usually #10 sized
    • Can be used circular bearings and special bushings

13 of 20

Shafts

  • MAXSpline
    • Special System
      • Specific gears, bearings, structure
    • Strong but bulky and annoying to use
      • Expensive
  • Churro
    • Structure
    • Acts similarly to ½” hex shaft, weaker for rotational motion
    • ¼” through hole

14 of 20

Bearings

  • Supports shafts
  • Has a set of rolling balls within a case
  • FRC Typical Bearing:
    • ID: ½” Hex
    • OD: 1-⅛” Rounded, not including the flange
    • Flanged
  • Comes many many sizes and types not covered today

15 of 20

Chain and Sprockets

  • Types
    • #25 and #35 chain, #35 is bigger
  • High Loads, lower speed
  • Extremely heavy, all metal parts
  • Usually used for applications that do not require a full rotation (reciprocating/restricted motion)
    • Example: arms and elevators
    • Exception: Bikes
    • Inline tensioners can be used when this is true
    • Otherwise an idling tensioner must be used

16 of 20

Chain and Sprockets

  • Uses a calculator to calculate center-to-center distance
  • Must be close to exact, can use inline tensioner to make exact

17 of 20

Belts and Pulleys

  • Types
    • HTD 5mm (9mm or 15mm width)
    • GT2 3mm (9mm width)
  • Lower Loads, faster speed
  • Much lighter, usually mostly/all plastic/rubber parts
  • Usually used for applications that require full rotations
    • Example: drivetrains, intakes, shooters
    • Tensioners used sometimes, but not usually necessary

18 of 20

Belts and Pulleys

  • Uses a calculator to calculate center-to-center distance
  • Try to be as exact as possible
  • Can be slightly too close

19 of 20

Hubs

  • Transferring motion from a shaft to structural part
  • The part that moves the structure
  • Mates with bearing block in some cases

20 of 20

Conclusion

  • Producing Motion is Hard
  • Ask Questions
  • Double check dimensions
  • Consult mentors
  • This was a gross oversimplification
  • Much more math and programming involved