JavaScript isn't enabled in your browser, so this file can't be opened. Enable and reload.
Hammer Drill
*必填
Sign in to Google
to save your progress.
Learn more
* Indicates required question
1
*
Look over all of the drill and search for any scratches, marks, paint or silicon. Any visual defects should disqualify the product.Check the screws are intact, ensure no screws were missing on the drill. 检查整个电钻外观。是否有任何划痕，标记，油漆或胶水。任何视 觉缺陷都视为不良品。检查螺丝是否完整，不能有螺丝遗漏情况。
Required
2
*
Turn the chuck hard to check whether there is a bearing inside. 扳动夹头，观察轴承是否安装。
Required
3
*
Ensure that the C-lock in place, pull the switch after assembly to ensure that the switch will not be pulled out. 确保C型卡簧安装到位，安装之后用力拉开关，确保开关不会被拉出。
Required
4
*
Check the Oring in air tap，is deformed and beyond the air tap. 检查气嘴的密封圈是否变形超出气嘴。
Required
5
*
Make sure the SS clip is assembled right. 绳子金属扣的光滑面要向上。
Required
6
*
The glue that connect the connector and basement should be smooth, and the surface of glue should be just flush with the connector surface. There can be no trace of residual glue in other places. Check whether the tool joint is abnormal. Pins that are black or damaged are not qualified. 底座打胶要光滑，胶的表面应刚好和接头平面齐平，其他地方不能有残留的打胶痕迹。检查工具接头有无异常，插针发黑、破损的不合格。
Required
7
*
Open /close the battery lock mechanism. It should be easy to open and close without to much force. 反复打开/锁上电池。确保能够轻易的打开和锁上，不用费多大力气。
Required
8
*
With battery inside, move the direction switch left and pull the trigger. Move it right and pull the trigger. Make sure left/right is working smoothly.Also make sure when the direction switch left, the drill is running in clockwise 接上电池，左右移动方向开关，扣动扳机。确保左/右方向运转流畅。并确保当开关按向左边时所对应的是正转。
Required
9
*
Make sure the on&off switch has the speed adjustion function.Press the switch deeper,The speed will be faster. 确保电源开关具有调速功能。随着开关按压深度的增加而速度增加。
Required
10
*
With battery inside, pull trigger fast to make sure the current limit isn’t stopping the drill. Listen for strange mechanical noise. 接上电池，调到高速档模式，扣动扳机检查转头是否运转正常。听是否有机械噪音。
Required
11
*
The testing of the speed switch：①Start the drill，it should be low speed when the switch fiddled to the front；②After the chuck being installed，switch the drill to the "attack" position，keep the drill working on a high speed level at least 30 seconds，look if the switch slides because of Vibration. 调速开关的测试：①开动电钻，当调速开关往前拨时为低速，往后拨为高速；②装好夹头后，将电钻调至冲击档，开动电钻至高速档 30秒以上，观察调速开关是否会由于振动而自己转动跑位。
Required
12
*
look inside the chuck. Make sure there is a screw to hold the chuck in place.check whether the LED light works or not. 查看夹头里面。确保有一个螺丝固定夹头。检查LED灯是否正常。
Required
13
*
Hold the chuck, test the chuck opening from the minimum to maximum, and then from the maximum to minimum, repeated three times, whether the test will be idle and noise 用手握住夹头，将夹头的开口从最小调到最大，再从最大调到最小，重复3次，测试是否会空转并发出噪音。
Required
14
*
Set the drill to the maximum torque value,Make sure corresponding position is ▌. And to ensure fast and slow-speed setting are sufficiently strong. 检查数字配件在最大扭矩值时所对应的位置是否对准 ▌。 并确保在快速档和慢速档都有力
Required
15
*
Adjust to the impact function, and slowly press the switch with your hand to check whether the chuck vibrates and the sound of impact. 调到冲击功能，用手慢慢按开关，检查夹头有没有震动和发出撞击的声音。
Required
By
*
Your answer
Submit
Clear form
Never submit passwords through Google Forms.
This form was created inside of NemoPowerTools.
Report Abuse
Forms
