Clothing Pre-Assessment
In Google anmelden, um den Fortschritt zu speichern. Weitere Informationen
What is your name? *
Directions: Correctly identify each part of the machine.
1. Stitch Width Control *
2. Presser Foot *
3. Spool Pin *
4. Upper Thread Tension Selector *
5. Stitch Length Control/Backstitch Knob *
6. The Presser Foot Lever is shown below in picture: *
7. The Bobbin Case is shown below in picture: *
8. The Foot Pedal is shown below in picture: *
9. The Feed Dogs are shown below in picture: *
Directions: Correctly identify each part of the machine
10. Thread Take-Up Lever *
11. Decorative Stitches *
12. Buttonhole Stitch Selector *
13. Handwheel *
14. Stitch Plate *
Directions: Match the following pieces of sewing equipment to their functions.
15. Must be kept sharp and used ONLY on fabric. *
16. Used for measuring long distances, straight of grain, and body measurements. *
17. Useful in removing small stitches. *
18. Temporarily holds layers of fabric together for cutting and sewing. *
19. Metal 6-inch ruler with a sliding marker. *
Directions: Match the following pieces of pressing equipment to their picture.
20. Steam Iron *
21. Tailor's Ham *
22. Sleeve Board *
23. Ironing Board *
24. Sleeve Roll *
Directions: Match the following terms/techniques to the correct definitions.
25. Cutting V-shaped wedges out of the seam allowance. *
26. Trimming layers of seam allowance to decrease bulk. *
27. Long, temporary stitches used to hold pieces of fabric together. *
28. The space from the seam to the edge of the material. *
29. Diagonal angle of fabric. Provides the greatest amount of stretch in the fabric. *
Directions: Choose the option that best answers the following multiple choice questions.
30. The presser lever: *
31. Safety procedures when working with a serger include all of the following EXCEPT: *
32. Pressing is done in a(n): *
33. When pressing a garment, using a pressing cloth protects the fabric from: *
34. The best temperature setting for ironing or pressing synthetic fabric is: *
35. The outside edge of the presser foot is approximately _____________ from the needle when in the center position. *
36. The thread take-up lever needs to be: *
37. The standard stitch width for seam allowances on most commercial patterns is: *
38. The rule for pressing is: *
39. A common reason for skipped stitches could be: *
40. When the stitches are not flat on both sides of the fabric after sewing, you should: *
41. Cotton is comfortable to wear. It also: *
42. Linen is: *
43. Synthetic fibers are: *
44. These fibers are less absorbent than natural fibers and are very heat sensitive: *
45. To press nylon, use: *
46. Blends are created in yarns and thread to: *
Directions: Match the following terms/techniques to the correct definitions on the right.
47. 2-3 parallel rows of lengthened stitches to create fullness in a garment. *
48. A tunnel through which elastic or cording is threaded. *
49. The tightly woven edge of fabric that runs parallel to the grainline. *
50. Short cuts made in the seam allowance, but not through the stitching, to allow for bendability. *
51. Parallel to the selvage edge. Provides the least amount of stress in a fabric. *
Directions: Match the following information with where it can be found.
52. Appropriate Size *
53. Selected Pattern Pieces *
54. Pattern Layout *
55. Fabric Type *
56. Notions and Yardage *
57. Construction Steps *
Directions: Circle the letter that best answers the following multiple choice questions.
58. Standard thread used for most sewing is: *
59. Stains should be: *
60. Ball point pen can often be removed by: *
61. When cutting out a pattern, the notch is: *
62. The fold line, (or place-on-fold line), on a pattern is: *
63. Top stitching is: *
64. Fabrics with a high ______________ content need to be pre-washed. *
65. The straight of grain runs: *
66. When cutting one-way, nap, or directional prints: *
67. The bias runs: *
68. To reduce bulk in garments: *
69. To determine the length of a buttonhole: *
70. Casings for elastic or drawstring should be: *
71. The _______________ sewing machine needle is ideal for knit AND woven fabrics. *
72. Which of the following is a safety precaution when working on a sewing machine? *
73. A seam finish is: *
74. Specialty threads include all of the following EXCEPT: *
75. How is a serger different from a regular sewing machine? *
76. The feed dogs on a sewing machine *
77. A rotary cutter: *
78. To correctly pin a pattern piece to the fabric, the pins should: *
79. Interfacing is used primarily to: *
80. The handwheel should always be turned: *
81. A stitch is formed when: *
82. It is important to remove lint, and oil/maintenance a sewing machine: *
83. When the sewing machine snags fabric, it is probably because: *
84. When pinning a project to cut it out, pins should be placed:
Auswahl löschen
85. When transferring markings form the pattern to your fabric, all of the following are good ways to do it, EXCEPT: *
86. When sewing on a thick material, like denim, it is important to: *
87. "Mitered corners" are used on: *
88. A fabric that has interlocking loops is known as a: *
Directions: Match the ruler markings with the correct measurements.
89. 5/8" *
90. 3/8" *
91. 1/2" *
92. 1/4" *
93. 3/4" *
Directions: Use the chart below to answer the following questions.
94. Using the chart above, identify how much material you would need to make dress "A" in size 14, with a 45" wide fabric. *
95. Using the chart above and the provided measurements (Bust 34, Waist 26, Hip 36) determine which size should be made. *
Senden
Alle Eingaben löschen
Geben Sie niemals Passwörter über Google Formulare weiter.
Dieses Formular wurde bei Washington County School District erstellt. Missbrauch melden
Google Formulare