Page 1 of 4
GOVERNMENT INDUSTRIAL TRAINING INSTITUTE CUDDALORE
FITTER THEORY MODEL TEST
Mark:150
-----------------------------------------------------------------------------------------------------------------------------
1
A. Square file B, Triangular file
C. Half round file D. Knife edge file
Choose the correct answer.
-----------------------------------------------------------------------------
2
A. One fourth B. One third C. Half D. One sixth
Choose the correct answer.
-----------------------------------------------------------------------------
3
A. Filing general purpose
B. Filing soft materials
C. Filing at right angles to a finished surface
D. Filing at corners of the job
Choose the correct answer.
-----------------------------------------------------------------------------
4
A. Clearance angle B. Rake angle
C. Point angle D. Angle of inclination
Choose the correct answer.
-----------------------------------------------------------------------------
5
A. Flat chisel B. Diamond point chisel
C. Cross cut chisel D. Half round nose chisel
Choose the correct answer
-----------------------------------------------------------------------------
6
A. End to end of blade
B. Centre of one pin hole to the centre of another pin hole
C One end of the toothed portion to the other end
D. End of one hole to the end of the other pin hole
GOVERNMENT INDUSTRIAL TRAINING INSTITUTE CUDDALORE
FIRST SEMESTER
FITTER THEORY MODEL TEST-I
--------------------------------------------------------------------------------------------------------------------------------------------------------------
Mark:3
-----------------------------------------------------------------------------
Mark:3
A. One fourth B. One third C. Half D. One sixth
-----------------------------------------------------------------------------
3 Mark:3
-----------------------------------------------------------------------------
4 Mark:3
-----------------------------------------------------------------------------
Mark:3
A. Flat chisel B. Diamond point chisel
C. Cross cut chisel D. Half round nose chisel
-----------------------------------------------------------------------------
6 Mark:3
B. Centre of one pin hole to the centre of another pin hole
7 Mark:3
A. Chipping with light force when r
B. Chipping using soluble oil
C. Holding the chisel with less inclination
D. The end portion is chipped from opposite direction
Choose the correct answer.
-----------------------------------------------------------------------------
8
A, Shape B. Cut C. Grade D. Section
Choose the correct answer.
-----------------------------------------------------------------------------
9
A. 65° B. 60' C.50° D.55°
Choose the correct answer.
-----------------------------------------------------------------------------
10
A. Steel rule B. Caliper C. Try square D. Jenny caliper
Choose the correct answer.
-----------------------------------------------------------------------------
11
A. They have large surface area
B. They providee the datum surface
C. Marking tools can slide over easily
D. They with stand heavy weight of jobs
Choose the correct answer.
-----------------------------------------------------------------------------
12
A. Bevel gauge B. Universal bevel gage
C. Bevel protractor D. Angle gauge
GOVERNMENT INDUSTRIAL TRAINING INSTITUTE CUDDALORE
Time:2Hrs
----------------------------------------------------
7 Mark:3
A. Chipping with light force when reaching the end
C. Holding the chisel with less inclination
D. The end portion is chipped from opposite direction
-----------------------------------------------------------------------------
8 Mark:3
C. Grade D. Section
-----------------------------------------------------------------------------
9 Mark:3
A. 65° B. 60' C.50° D.55°
-----------------------------------------------------------------------------
10 Mark:3
C. Try square D. Jenny caliper
-----------------------------------------------------------------------------
11 Mark:3
B. They providee the datum surface
C. Marking tools can slide over easily
D. They with stand heavy weight of jobs
-----------------------------------------------------------------------------
12 Mark:3
A. Bevel gauge B. Universal bevel gage
C. Bevel protractor D. Angle gauge
Page 2 of 4
13
A. Divider B. Trammel C. Scriber D. Jenny caliper
Choose the correct answer.
-----------------------------------------------------------------------------
14
A. Centre head with rule B. Protractor head
C Square head with rule D. Square head
Choose the correct answer.
-----------------------------------------------------------------------------
15
A. Shape of the work B. Accuray of tool used
C. Type of marking media applied D. Layout the drawing
Choose the correct answer.
-----------------------------------------------------------------------------
16
A. To support small shafts B. To support long shafts
C. To support two different shafts D. To support bearings
Choose the correct answer.
-----------------------------------------------------------------------------
17
A. To check the squareness of filed surface
B. To check the flatness of surface
C. To check the linear measurement of job
D. To mark lines at 90° to the edge of jobs
Choose the correct answer.
-----------------------------------------------------------------------------
18
A. Fixed jaw B. This is knurled part C. Hard jaws
----------------------------------------------------------------------------
19
A. It can hold the jobs having parallel sides
B. it is fixed parallel to shop floor
C. Its width of jaws are parallel
D. its movable jaw moves parallel to the fixed jaw
Choose the correct answer.
-----------------------------------------------------------------------------
20
A. Pipe vice B, Hand vice C. Pin vice D. Tool makers vice
Choose the correct answer.
Mark:3
A. Divider B. Trammel C. Scriber D. Jenny caliper
-----------------------------------------------------------------------------
14 Mark:3
-----------------------------------------------------------------------------
15 Mark:3
B. Accuray of tool used
D. Layout the drawing
-----------------------------------------------------------------------------
Mark:3
B. To support long shafts
D. To support bearings
-----------------------------------------------------------------------------
17 Mark:3
-------------------------------
Mark:3
D. Spindle
----------------------------------------------------------------------------
Mark:3
-----------------------------------------------------------------------------
Mark:3
C. Pin vice D. Tool makers vice
21
A. Cross pein hammer B. Straight
C. Soft hammer D. Ball pein hammer
-----------------------------------------------------------------------------
22
A. Face B. Cheek C. Pein D. eye hole
----------------------------------------------------------------------------
23
A. Cross pein hammer B. Sledge hammer
C. Ball peen hammer D. soft hammer
Choose the correct answer.
---------------------------------------------------------------------
24
A. Sub division B. Main scale division
C. Vernier scale division D. Additional
Choose the correct answer.
-----------------------------------------------
25
A. Sub scale division B. Main scale division
C. Zero reading D. Least count
Choose the correct answer.
-----------------------------------------------
26
A, 0.001mm B. 0.01mm C. 0.02mm D. 0.002mm
Choose the correct answer.
--------------------------------------------
27
A. It has long sleeve
B. It is equipped with number of extension rods.
C. It has long spindle
D. It has an adjustable base
Choose the correct answer.
-----------------------------------------------------------------------------
28
A. 0.01 mm - B. 0,002mm C. 0.001 mm
Choose the correct answer.
-----------------------------------------------
Mark:3
A. Cross pein hammer B. Straight pein hammer
C. Soft hammer D. Ball pein hammer
-----------------------------------------------------------------------------
Mark:3
A. Face B. Cheek C. Pein D. eye hole
-----------------------------------------------------------------------------
Mark:3
A. Cross pein hammer B. Sledge hammer
C. Ball peen hammer D. soft hammer
-----------------------------------------------------------------------------
Mark:3
A. Sub division B. Main scale division
C. Vernier scale division D. Additional sub divisions
-----------------------------------------------------------------------------
Mark:3
A. Sub scale division B. Main scale division
C. Zero reading D. Least count
-----------------------------------------------------------------------------
Mark:3
A, 0.001mm B. 0.01mm C. 0.02mm D. 0.002mm
-----------------------------------------------------------------------------
Mark:3
B. It is equipped with number of extension rods.
-----------------------------------------------------------------------------
Mark:3
B. 0,002mm C. 0.001 mm D. 0.02mm
-----------------------------------------------------------------------------
Page 3 of 4
29
A. Thumb lever B. Depth bar
C. Vernier slide D. Knurled nut
Choose the correct answer.
Choose the correct answer.
-----------------------------------------------------------------------------
30
A. 9.246mm B. 9.24mm C. 9.32 mm D. 9.44 mm
Choose the correct answer.
-----------------------------------------------------------------------------
31
A. External measurements B. Holes, recesses, slots and steps
C. Internal measurements D. Pitch diameter
Choose the correct answer.
-----------------------------------------------------------------------------
32
A. dial to blade B. blade to the dial
C. Blade to disc D. Dial to disc
Choose the correct answer.
------------------------------------------------------------------------------------
33
A. Dial B. Disc C. Blade D. Stock
Choose the correct answer.
-----------------------------------------------------------------------------
34
A. Solid punch B. Hollow punch C. Pin punch D. Centre punch
Choose the correct answer.Choose the correct answer.
-----------------------------------------------------------------------------
35
A. Three times the thickness of sheet
B. Two times the thickness of the sheet
C. No allowances
D. Four times the thickness of the sheet
Choose the correct answer.
Choose the correct answer.
Mark:3
-----------------------------------------------------------------------------
Mark:3
9.44 mm
-----------------------------------------------------------------------------
Mark:3
A. External measurements B. Holes, recesses, slots and steps
-----------------------------------------------------------------------------
Mark:3
------------------------------
Mark:3
-----------------------------------------------------------------------------
Mark:3
C. Pin punch D. Centre punch
Choose the correct answer.
------------------------------
Mark:3
36
A. Number size B. Letter size
C. Standard size D. Standard gauge numbers
Choose the correct answer.
-----------------------------------------------------------------------------
37
A. Notching the sheets
B. Cut sheets which cannot be cut with hand shears.
C. Bending the Sheets
D. Folding the Sheets
-----------------------------------------------------------------------------
38
A. Standard wooden mallet B. End
C. Bossing mallets D. Plastic mallet
Choose the correct answer.
-----------------------------------------------------------------------------
39
A. Half moon stake B. Funnel stake
C. Beak or back iron D. Creasing iron
-----------------------------------------------------------------------------
40
A. Single seam B. Double seam
C. Lap seam D. Double grooved seam
Choose the correct answer.
-----------------------------------------------------------------------------
41
A. Light in weight B. More density
C. Can be welded easily D. Cheapest metal
Choose the correct answer.
-----------------------------------------------------------------------------
42
A. Shovel B. Tongs C. Rake D. Poker
Choose the correct answer.
-----------------------------------------------------------------------------
43
A. Rectangular top surface B. Square hole
C, Round tapered D. Bottom portion
Choose the correct answer.
-----------------------------------------------------------------------------
Mark:3
D. Standard gauge numbers
---------------------------------------------------------
Mark:3
B. Cut sheets which cannot be cut with hand shears.
-----------------------------------------------------------------------------
Mark:3
B. End - faked mallet
C. Bossing mallets D. Plastic mallet
-----------------------------------------------------------------------------
Mark:3
stake B. Funnel stake
Beak or back iron D. Creasing iron
-----------------------------------------------------------------------------
Mark:3
A. Single seam B. Double seam
C. Lap seam D. Double grooved seam
-----------------------------------------------------------------------------
Mark:3
A. Light in weight B. More density
C. Can be welded easily D. Cheapest metal
-----------------------------------------------------------------------------
Mark:3
A. Shovel B. Tongs C. Rake D. Poker
-----------------------------------------------------------------------------
Mark:3
A. Rectangular top surface B. Square hole
pered D. Bottom portion
-----------------------------------------------------------------------------
Page 4 of 4
44
A. Yellow B. Dark cherry red C. White D. Light yellow
Choose the correct answer.
-----------------------------------------------------------------------------
45
A. Fold B. Surface and internal cracks
C. Buckling of the stock D. Lap
Choose the correct answer.
-----------------------------------------------------------------------------
46
A. Sag B. Lap C. Fold D. Axial crack & Folds
Choose the correct answer.
-----------------------------------------------------------------------------
47
A. End upsetting B. centre upsetting
C. Drawing D. Jumping
Choose the correct answer.
-----------------------------------------------------------------------------
48
A. Hollow Tongs B. Round tongs
C. Square mouth tongs D. Flat tongs
Choose the correct answer.
-----------------------------------------------------------------------------
49
A. Malleable cast iron B. Aluminum
C. Cast steel D. Steel
Choose the correct answer.
-----------------------------------------------------------------------
50 Mark:3
A. Bending die B. Bending block
C. Fork tool D. Bolster swages
Choose the correct answer.
-----------------------------------------------------------------------------
Mark:3
C. White D. Light yellow
-----------------------------------------------------------------------------
Mark:3
nal cracks
-----------------------------------------------------------------------------
Mark:3
A. Sag B. Lap C. Fold D. Axial crack & Folds
-----------------------------------------------------------------------------
Mark:3
-----------------------------------------------------------------------------
Mark:3
-----------------------------------------------------------------------------
Mark:3
-----------------------------------------------------------------------------
50 Mark:3
-----------------------------------------------------------------------------