AlfaOBD Known Working Settings
Auto Dim High Beams: (https://www.ramforum.com/posts/1889005/)( https://www.ramforum.com/posts/2032277/) Thanks Ricks Ram for clarification
Vehicle Configuration 1: Auto High Beam
Select “yes”
Vehicle Configuration 3: Interior EC Mirror Present
Select“yes”
LIN & Misc: Smart Beam Present (AHBM)
Select “yes"
2014 CBC I/O & Features: Auto High Beam Module Location
Select “ECC_AHBM"
Customer Service Menus: Auto High Beam CSM
Select “yes”
Mirrors Interior Rear View and Exterior: (signal, puddle, dim)
Vehicle Configuration 3: Interior EC Mirror Present (Rear view mirror)
Doors: Mirror Turn Signal Present
Select “yes”
Doors: Electro-chromatic driver mirror present
Select “yes”
Doors: Electro-chromatic passenger mirror present
Select “yes”
Doors: Mirror Approach Lights Present
Select “yes”
Under “program customer features”
EC Mirror Auto Dim (Rear view mirror)
Select “enable” ...I believe this merely turns on/off the auto dim mirror which can also be accomplished through the menu settings or soft key on the 8.4 screen.
Tow Mirror Flip Up Correction:
Doors: Tow Mirrors Present
Select “yes”
Auto Tilt Mirrors in Reverse: For premium mirrors (chrome capped with more than 4 wires on white plug)
Doors: Driver Memory Mirrors Present
Select "Yes"
Doors: Passenger Memory Mirrors Present
Select "Yes"
CustSetMenu 2: Tilt mirror in reverse
Select "Yes"
Power Folding Mirrors: (If door modules and switch is installed)
Doors-Folding mirrors present
Fog lamps with high beams:
CBC Features: Fog lamp dropout enable
Select "No"
Vehicle Configuration 3: HVAC Configuration:
Note: “With an aftermarket radio and the maestro, you can only set it to “dual zone ATC” to have it work properly. I have the same set up, and if you try to go to “ATC single zone”, it will glitch out. This is because the maestro is flashed to a Ram truck, and all it knows the ram to have is either single mtc, dual mtc, or dual ATC.” Jimmy07
https://www.ramforum.com/posts/1984145/
Select:
Dual Zone ATC
Disconnect AlfaOBD app & shut off the truck for a few minutes and you must wait for the Dual Temp sliders to display on the 8.4 radio before proceeding with single zone ATC change.
(Battery disconnect between can speed up the radio/BCM reset for changes, especially with a UAx radio)
Select:
Single Zone ATC
Nav Setting to disable/enable turn by turn on EVIC through 8.4:
Nav turn by turn
Select “yes”
EVIC Splash Screen (for Limited logo): (2015 to present trucks)
Vehicle Configuration 1: Special Package
Select "Limited"
Vehicle Configuration 2: Special Package
Select "Limited"
SRT Splash on 8.4 Screen Boot:
Vehicle Configuration 3: Vehicle is an SRT
Select "yes"
DRLs: (Daytime Running Lights) For “Dedicated” DRLs (Rams with factory projectors) see post #7079
https://www.ramforum.com/posts/2032174/
CBC Features: DRL Configuration
Select “Optional DRL”
CBC Features: DRL Lamp location (several to choose from, high beam, low beam, fog lamp, dedicated and SRT Light Bar) Known working high beam, low beam, turn signal and fog lamp.
CBC Features: DRL Dropout Enabled
Select “yes”
ECU 3: DRL Customer Setting Enable/Disable
Select “yes”
Customer Service Menus: Daytime Running Lights CSM
Select “yes”
2014 CBC I/O & Feature: Truck Bed Lighting Feature
Select “yes”
Front Windows with Fob:
Doors: Global Up (not currently working)
Select “yes”
Doors: Global Down
Select “yes”
Trailer Brake Controller:
Trailer select csm
Select “yes”
Trailer name csm
Select “yes”
Trailer type csm
Select “yes”
P/T chassis net-ITBM/HWM integrated trailer brake module
Select “enable”
Rear View Camera:
Rear View Camera
Rear Camera Present
Rear Camera CSM
Rear View Camera Delay CSM
Trailer Hitch Camera
Rear View Camera Dynamic Gridlines Enabled - Or - Static Gridlines Enabled
Cargo Camera:
CHMSL Camera
Select “yes”
LED CHMSL Lamp Present
Select “yes”
Compass Heading (Evic):
Display Compass Heading Present
Select “yes”
Enable TravelLink on 2013-2018 8.4 Nav Radios (Mpgrimm2):
(Ricks_Ram “The 2013 to 2017 radios have the app built into them so it doesn't matter if you have your BCM enabled or not but on the 2018 and up UAQ radios they read the Travel Link feature directly off of your BCM so if you're Travel Link is not enabled in your truck it will not appear in your settings menu.)
SDAR Travel Link Feature Present
Select “yes”
Door Handle LED (mjf6175):
Door Handle LED Present
Push Button Start (Keyless Entry) (mjf6175 - See Notes):
VehConfig 3 - Keyless Go Present
VehConfig 3 - Passive Entry Present
VehConfig 3 - FOBIK Safe Enabled
LIN and Misc - Auto Relock Time
CustSetMenu 1 - Passive Entry CSM
Rain Sense:
VehConfig 2-Rain sensor Present
CustSetMenu 1 Rain sensitive wipers CSM
Calibration may need to be ran for adding the sensor and after adding the codes. Check for proper operation before running “Light Rain Sensor Calibration” or “Light Rain Sensor Re-Adaptation”. This has not been tested! Edit: This was not needed in my case. The BCM picked up on and the sensor functioned as it should.
Remove Service Air Suspension Message:
P/T Chassis Net-ASCM Air Suspension Control Module
"Not enabled"
Memory seats, Mirrors, Easy Exit Seats and Memory Linked to Fob:
Memory Seat:
Cabin Net - MSM Memory Seat module
Memory - Memory Seat Present
ECUConfig 3 - Memory CSO Present
Easy Exit Seat:
CustSetMenu 1 - Easy exit seat CSM
RKE Linked to Memory:
CustSetMenu 2 - RKE linked to memory CSM
Memory Mirrors:
Doors - Passenger Memory Mirror Present
Doors - Driver Memory Mirrors Present
Notes: They have to pin the 4 wires in the yellow driver's seat plug in order for them to work. Two to the CAN pin #5 and #6 and two to the drivers door module. Pin #2 and #13. You don’t need memory mirrors for the memory seats to work but you do need to be wired to the door module. ~Ricks_Ram
Heated/Vented Seats with Heated Wheel (with Rear Heated Seats):
Memory-Front Vented Seats Present
ECUConfig 3-Front Vented Seats Present
ECUConfig 3-Front Heated Seats Present
ECUConfig 3-Heated Steering Wheel Present
Memory-Rear Heated Seats Present
CustSetMenu 1-Auto-on driver comfort CSM (option 2-3)
Memory-Heated Steering Wheel Present
ECUConfig 4-Heated Seat Present
Memory-Heated Wheel Material Type
Memory-Heated Seat Material Type
Post for details
https://www.ramforum.com/posts/2024966/ To https://www.ramforum.com/posts/2025119/
Thank you @Ricks_Ram
Adding factory fog lights:
CBC I/O - Front Fog Lamps Output Present
Adding Factory CD:
Cabin Net - EDM External Disc Module
Homelink Electric Overhead Console Module:
LIN and Misc - EOM Present
Factory Inverter:
VehConfig 2-Power InverterType (Latching Switch)
ECUConfig 3-Power Inverter Present
Vehicle Settings Menu 7” EVIC: (needed when going from 3” standard to 7” premium EVIC to show radio settings menu. Especially important for aftermarket radio such as the Tesla unit) Post @Lawsuit 11
ECUConfig 4-IPC Feature Configuration
HID Lamps: (when installing high intensity discharge lamps to remove PWM) Post @Jimm07 here and here
VehConfig 3-High Intensity Discharge Lamps