Modified By,
Technical Team, REES52
#define BLYNK_PRINT Serial
#include <SPI.h> // Library for SPI
#include <Ethernet.h> // Library for Ethernet
#include <BlynkSimpleEthernet.h> // Library for Blynk
// You should get Auth Token in the Blynk App.
// Go to the Project Settings (nut icon).
char auth[] = "52861cfcce7c48a097fb3cbb190c5fdc";
#define W5100_CS 10
#define SDCARD_CS 4
#define red 11 // Digital Pin for Red
#define green 10 // Digital Pin for Green
#define blue 9 // Digital Pin for Blue
/* The setup() function is called when a sketch starts. It is used to initialize variables, pin modes, start using libraries, etc. This function will only run once, after each power up or reset of the Arduino board. */
void setup()
{
// Debug console
Serial.begin(9600); // Baud Rate
pinMode(SDCARD_CS, OUTPUT);
digitalWrite(SDCARD_CS, HIGH); // Deselect the SD card
Blynk.begin(auth);
// You can also specify server:
//Blynk.begin(auth, "blynk-cloud.com", 80);
//Blynk.begin(auth, IPAddress(192,168,1,100), 8080);
// Setup notification button on pin 2
}
BLYNK_WRITE(V1) // Run this function when V1 button pressed.
{
int x = param[0].asInt();
while(x==1) // When both values are equal
{
x = param.asInt(); // Initialize x
int i=0,j=0,k=0; // Store values in variables
// Function to output PWM Signal
analogWrite(red, 255); // Pin 11 is HIGH
analogWrite(green, 255); // Pin 10 is HIGH
analogWrite(blue, 255); // Pin 9 is HIGH
for(int j=0;j<20;j++)
{
analogWrite(red, 0); // Pin 11 is LOW
analogWrite(green, 255); // Pin 10 is HIGH
analogWrite(blue, 255); // Pin 9 is LOW
delay(100); // Wait for 100 ms
analogWrite(red, 255); // Pin 11 is HIGH
analogWrite(green, 0); // Pin 10 is HIGH
analogWrite(blue, 255); // Pin 9 is HIGH
delay(100); // Wait for 100 ms
analogWrite(red, 255); // Pin 11 is HIGH
analogWrite(green, 255); // Pin 10 is HIGH
analogWrite(blue, 0); // Pin 9 is LOW
delay(100); // Wait for 100 ms
x = param.asInt();
if(x==0) // When x value equals 0
break;
}
analogWrite(red, 255); // Red is HIGH
analogWrite(green, 255); // Green is HIGH
analogWrite(blue, 255); // Blue is HIGH
for(int z=0;z<10;z++)
{
for(i=0;i<=180;i++)
{
analogWrite(red, 180-i); // Variations for Red
delay(2); // Wait for 2 ms
}
analogWrite(red, 255); // Red is HIGH
for(j=0;j<255;j++)
{
analogWrite(green, 255-j);
delay(2); // Wait for 2 ms
}
analogWrite(green, 255); // Green is HIGH
for(k=0;k<255;k++)
{
analogWrite(blue, 255-k);
delay(2); // Wait for 2 ms
}
analogWrite(blue, 255); // Blue is HIGH
x = param.asInt();
if(x==0) // when x value equals 0
break;
}
analogWrite(red, 255); // Red is HIGH
analogWrite(green, 255); // Green is HIGH
analogWrite(blue, 255); // Blue is HIGH
for(int z=0;z<5;z++)
{
for(j=0;j<255;j++)
{
analogWrite(green, 255-j);
delay(20); // Wait for 20 ms
}
for(k=0;k<255;k++)
{
analogWrite(blue, 255-k);
delay(20); // Wait for 20 ms
}
for(i=0;i<=180;i++)
{
analogWrite(red, 180-i);
delay(20); // Wait for 20 ms
}
analogWrite(red,180); // Red is HIGH
x = param.asInt();
if(x==0) // When x values equals 0
break;
}
if(x==0) // When x values equals 0
break;
}
analogWrite(red, 255); // Red HIGH
analogWrite(green, 255); // Green HIGH
analogWrite(blue, 255); // Blue HIGH
}
/* The loop() function executes the program repeatedly until Specified. */
void loop()
{
Blynk.run();
}