Voyager™ 1400g Series

Corded Area-Imaging Scanner

Quick Start Guide

Aller à www.honeywellaidc.com pour le français.  

Vai a www.honeywellaidc.com per l'italiano.  

Gehe zu www.honeywellaidc.com für Deutsch.  

Ir a www.honeywellaidc.com para español.  

Para Português, acesse www.honeywellaidc.com.br.  

Перейти на русскоязычный сайт www.honeywellaidc.com.  

Pro češtinu jdi na www.honeywellaidc.com.  

Pre slovenčinu choď na www.honeywellaidc.com  

日本語:  www.honeywellaidc.com をご覧ください。

如要到中国 www.honeywellaidc.com简体)한글  www.honeywellaidc.com  이동합니다 .

VG1400-QS Rev A

6/12

Note: Refer to your user’s guide for information about cleaning your device.

For localized language versions of this document, go to www.honeywellaidc.com. Getting Started

Turn off computer’s power before connecting the scanner, then power up the computer once the scanner is fully connected.

Power Supply Assembly (if included)

Connecting the Scanner USB: 

Reading Techniques

The view finder projects an aiming beam that should be centered over the bar code, but it can be positioned in any direction for a good read.

Hold the scanner over the bar code, press the button, and center the aiming beam on the bar code.

The aiming beam is smaller when the scanner is closer to the code and larger when it is farther from the code.  Hold the scanner close to smaller bar codes, and farther away from large bar codes to get a proper read.  

If the bar code is highly reflective (e.g., laminated), you may need to tilt the scanner at an angle so the bar code can be scanned.

Note: PDF bar codes can only be read by Voyager models

1400gPDF or 1400g2D and cannot be read by model

1400g1D.  2D bar codes can only be read by Voyager model

1400g2D and cannot be read by models 1400g1D or 1400gPDF.

Standard Product Defaults

The following bar code resets all standard product default settings.

Standard Product Defaults

RS485 Interface

The RS485 interface defaults to port 5B.  If you have an IBM POS terminal using port 9B, scan the appropriate code below to program the terminal, then power cycle the cash register.

IBM Port 9B HHBCR-1

Interface

IBM Port 9B HHBCR-2

Interface

Note: For additional RS485 interface selections, see the User’s Guide for your product at our website, www.honeywellaidc.com.

Keyboard Country

Scan the Program Keyboard Country bar code below, then scan the numeric bar code(s) from page 11, then the Save bar code to program the keyboard for your country.  As a general rule, the following characters are not supported by the scanner for countries other than the United States: 

@  |  $  #  {  }  [  ]  =  /  ‘  \  <  >  ~.

Program Keyboard Country

Country Code

Scan

Country Code

Scan

Belgium

1

Italy

5

Denmark

8

Norway

9

Finland

2

Spain

10

France

3

Switzerland

6

Germany/Austria

4

USA (Default)

0

Great Britain

7

Save

Note: For a complete list of country codes, see the User’s Guide for your product at our website,  www.honeywellaidc.com.

Trigger

The following bar codes will allow you to use the scanner in Manual

Trigger - Normal Mode (need to press the button to read) or Presentation mode (the scanner is activated when it “sees” a bar code).

Manual Trigger - Normal

(Default)

Presentation Mode

Suffix

If you want a carriage return after the bar code, scan the Add CR

Suffix bar code.  To add a tab after the bar code, scan the Add Tab Suffix bar code.  Otherwise, scan the Remove Suffix bar code to remove the suffixes.

Add CR Suffix

Add Tab Suffix

Remove Suffix

Add Code ID Prefix to all Symbologies

Scan the following bar code if you wish to add a Code ID prefix to all symbologies at once.

Add Code ID Prefix To All Symbologies (Temporary)

Note: For a complete list of Code IDs, see the User’s Guide for your product at our website,  www.honeywellaidc.com.

Function Code Transmit

When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal.  Charts of these function codes are provided in your User’s Guide.  When the scanner is in keyboard wedge mode, the scan code is converted to a key code before it is transmitted.

Enable

(Default)

Disable

Data Format Editor Instructions

The following are abbreviated instructions for entering a data format.  For complete instructions refer to your User’s Guide, available at our website, www.honeywellaidc.com.

  1. Scan the Enter Data Format symbol.
  2. Primary/Alternate Format: scan 0 for Primary Format
  3. Terminal Type: scan 099 for any terminal type
  4. Code I.D.: scan 99 for any bar code type
  5. Length: scan 9999 for any length bar code.
  6. Editor commands: use the Programming Chart that follows.
  7. Scan Save to save your entries.

Enter Data Format

Clear All Data Formats

Save

Programming Chart

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

Save

EZConfig-Scanning

To access additional features for the scanner use EZConfigScanning, an online configuration software tool, available from our website at www.honeywellaidc.com. 

Technical Assistance

Contact information for technical support, product service, and repair can be found at www.honeywellaidc.com. Limited Warranty

Refer to www.honeywellaidc.com/warranty_information for your product’s warranty information.

Patents

For patent information, refer to www.honeywellaidc.com/patents.

User Documentation

For localized versions of this document, and to download the User’s Guide, go to www.honeywellaidc.com.

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.  The information in this publication does not represent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.

This document contains proprietary information that is protected by copyright.  All rights are reserved.  No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII.

© 2012 Honeywell International Inc.  All rights reserved. Web Address: www.honeywellaidc.com