10/08/2018 - Chris
Boards tested to ship to OSU
4018 - All OK
4315 - All OK
5024 - All OK
5004 - All OK
4027 - All OK
4240 - All OK
4305 - All OK
4294 - All OK
15/07/2018 - Chris
Board 6051 - All OK (tested for DBM SR1)
13/04/2018 - Chris
Board from AFP tested: 6042
31/01/2018 - Chris
Boards tested from PIT all have at least one channel with back optical power…
4236 | 4171 |
4169 | 4218 |
5018 | 4068 |
4155 | 5047 |
4232 | 4154 |
5010 | 4201 |
5008 | 4147 |
5022 | 4211 |
5009 | 4125 |
4127 | 5043 |
25/01/2018 - Chris
Boards rested for PIT:
4315 -> All OK
4240 -> All OK
22/01/2018 - Chris
Boards tested for PIT:
5024 -> Removed from SR1 setup, All OK
5023 -> All OK
5065 -> All OK
4307 -> All OK
4308 -> All OK
4309 -> All OK
4310 -> All OK
4312 -> All OK
4313 -> All OK
4314 -> All OK
18/01/2018 - Chris
Boards tested for PIT:
5021 -> Tested again after removal of object from outside VCSEL, tried to blow air and it would not remove, so used a tweezer… Ch 7 has no OP and full error counts -> Given to Didier for potential wire bond repair
5064 -> Tested again after shaving of ruff edges - All OK
5036 -> All OK
4304 -> All OK, again issues with fiber labeled VCSEL1
4305 -> All OK,
4306 -> All OK
Boards for KK:
4117 -> Broken
4004 -> was 2nd class -> Only middle VCSEL working
4055 -> OP lower on outer VCSEL, no error counts
4042 -> OP and Errors OK… Might have an issue in fiber labeled VCSEL1 in setup… (Know we have an issue with this board, maybe VCSEL alignment?)
4112 -> OP and Errors OK
17/01/2018 - Chris
Boards prepared for the PIT:
5064 -> all great
4299 -> all great
4300 -> all great
4301 -> all great
4302 -> all great
4303 -> all great
16/01/2018 - Chris
Three D type boards to continue replacement:
4294 -> Issue with VDC channel 4… OP OK -> To be investigated
4295 -> All great
4296 -> all great
4297 -> all great
Boards extracted from PIT:
MEASUREMENTS DONE USING VCSEL 2 on outside and VCSEL 1 on middle
4256 -> No OP and full Errors on Ch 2 (Dark in picture)
4259 -> No OP and full Errors on Ch 5 (Dark in picture) Full Errors on Ch 12 (Also dark in picture) -> No OP Measurement???
4245 -> No OP and full Errors on Ch 4 & 10 (Both Dark in picture)
4247 -> No OP and full errors on Ch 3 & 5 (Both Dark in picture) Full Errors on Ch 12 (Also dark in picture) -> No OP Measurement???
4261 -> No OP and full errors on Ch 11 (Dark in picture)
5062 -> Swapped VCSEL fibers (put 2 in middle) then No OP and full errors on Ch 2 (also dark in picture)
15/01/2018 - Chris
Two B-type boards prepared for PIT replacement.
5021
5012
12/10/2018 - Chris
Test boards recommended for PIT replacement.
4085
4117
4207
4286
4290
All look good in both power and error counts.
11/01/2018 - Chris
Verify which boards are in SR1 ToothPix setup:
Pixel / counting room side
5003 (11)
5024 (10)
4265 (9)
4019 (8)
4011 (2)
4012 (3) -> Assumed
4013 (4) -> Assumed
4017 (5) -> Assumed
IBL / Clean room side:
6051 (23) -> DBM
6001 (17) -> IBL
6026 (18) -> IBL
6022 (13) -> IBL
Went through board storage to check presence of boards…
Updated: https://docs.google.com/spreadsheets/d/1ZQj8LxY1mZKpSWbUh-Ojd00JxqA506NC0cnced52YVc/edit#gid=0
10/01/2018 - Chris
History of Boards pulled out for qualification and possible PIT replacement:
4018 -> 6/4/2013: 384mA - all channels no errors, optical power OK -> 03/17/2014: scan #40435 -- all ok -> Week of 10/19/2015 Chris used for learning setup
4027 -> 6/4/2013: 380mA - all channels no errors, optical power OK -> 03/17/2014: scan #40413 -- all ok -> 16/04/2016: Optical power is okay, No error count
4036 -> 07/05/2013: 384mA, all channels no errors, optical power OK -> 08/06/2013: connected to optobox -> 1/27/2014: 384 mA, error counts test OK, optical powers OK -> 03/14/2014: scan #40364 -- all ok
4085 -> 10/01/2013: IVVDC = 383 mA, error counts test OK, optical powers are OK -> 01/31/2014: 383 mA, all ok. -> 03/18/2014: 2D-scan, scan #40550 -- all ok
4240 -> 1/27/2014: 391 mA, error counts test OK, optical power OK -> 03/17/2014: scan #40398 -- all ok
4018:
Turn on (defaults):
VVDC -> 2.47
IVVDC -> 238m
Iset (uA) -> 40.8
Ipin -> 957u
Ret Ipin 1 -> 2.23u
Ret Ipin 2 -> 619n
NTC -> 104m
All good power and errors
4018, 4027, 4036, 4085, 4240 -> All tested at 1mA Iset… all power OK and no Errors!
Set aside for PIT replacement.
06/10/2017 - Chris
Boards given for removal testing:
5040
4016
4010
4003
4054
5006
6016
22/03/2017 - Chris
6047 - Tested for ToothPixDBM… OP on VCSEL1 Bad. Physical inspection shows issues with pins on connector
6051 - OP and Error Good Installed for ToothPixDBM
15/11/2016 - Chirs
Boards used for removal practice
5006
4054
4003
6020
5040
4010
6016
4016
14/11/2016 - Chris
2026 - Tested for ToothPixIBL… OP GOOD, No Errors - Moved to ToothPixIBL
21/10/2016 - Chris
6047 - Installed in ToothPix for DBM
6022 - Installed in ToothPix for
06/09/2016 - Chris
6002 - Optical power a bit low… maybe loose fiber in setup, No Errors
6001 - Optical power is OK, No Errors - Moved to ToothPixIBL (23Sept2016)
6022 - Optical power is OK, No Errors
6000 - Fails Physical inspection. Did not test
20/08/2016 - Chris
6051 - Optical power is okay, no error count (used as control back to storage)
6003 - No optical power from VCSEL2, verified using phone camera
16/04/2016 - Chris
4013 - Optical power is okay, many DORIC errors
4018 - Optical power is okay, cannot find good region for DORIC errors (assume operator error)
4306 - Optical power is okay, cannot find good region for DORIC errors(assume operator error)
4286 - Optical power is okay, cannot find good region for DORIC errors(assume operator error)
4027 - Optical power is okay, No error count
4013 - RETEST, NO ERROR COUNT
10/29/2015 - Chris & Shane
5024 - Optical power is okay, No error count
5024 - Installed in ToothPix setup: slot 10 NOTE: sticks out because of plug in back. (Fibers not yet connected.)
10/27/2015 - Chris, Shane, Siinn
4018 - Optical power is okay, No error count
4015 - Broken DORIC fiber plug (Bent support on plug)
10/20/2015
5024 - Optical power is okay, No error count
4015 - Optical power from 0-6 is very low (0-50), errors are crazy not good
4018 - Optical power from 0-6 is very low (0-50), errors are crazy not good
10/19/2015 -- These tests performed by Chris not using default optical cables. Instead In1 & In2 on “black boxes” are plugged directly into optoboard. After many cleanings I suspect faulty optical cable.
4019 - Optical power is okay, No error count
4015 - Optical power from 0-6 is very low (0-50), error not tested
5024 - Optical power is okay, No error count
4018 - Optical power from 0-6 is very low (0-50), error not tested
10/16/2015
4012 - Optical power is okay, No error count
4017 - Optical power is okay, No error count
4011 - Optical power is okay, No error count
4013 - Optical power is okay, No error count
5003 - Optical power is okay, No error count
5024 - Optical power is okay, No error count
4265 - Optical power is okay, No error count
09/25/2015
4042 - Optical power is okay, No error count -- Chris training
07/24/2015
4005 - Optical power is okay. Error on channel 5
4011 - Optical power is okay. No error count
4012 - Optical power is okay. No error count
4013 - Optical power is okay. No error count
4015 - Optical power is okay. No error count
07/23/2015
6042 - Optical power is okay. No error count
6040 - Optical power is okay. No error count
6045 - Optical power is okay. No error count
6026 - Optical power is okay. No error count
5004 - Optical power is okay. No error count
5021 - Optical power is okay. No error count
5012 - Optical power is okay. No error count
07/17/2015
5023 - Optical power is okay. No error count
4265 - Optical power is okay. No error count
5003 - Optical power is okay. No error count
07/16/2015
5036 - Optical power is okay. No error counts
4002 - No error counts, Optical power is good only on VCSEL 2.
4002 7/16/2015 5:27:08 PM 4.676500E+2 3.760726E+2 4.173539E+2 4.239197E+2 4.060727E+2 2.464961E+2 3.724058E+2 2.880666E+3 2.933151E+3 3.020628E+3 2.725978E+3 3.345214E+3 3.762731E+3 3.458662E+3
01/15/2015
Stopping the run. The run was going fine, no error counts
Testing the optoboard 4082, taken from Bern.
4082- 415 mA, optical power OK, channel 4 has slow error count (~1 per 20 sec)
01/13/2015
The run is going fine, no error counts
01/07/2015
The run is going fine, no error counts.
12/18/2014
The run is going fine, no error counts.
12/16/2014
The test was unexpectedly stopped, the computer was shut down. Starting a new run at 9:40
12/10/2014
Starting a new long run with 6042 at 17:05
12/08/2014
End of the long run with the board 6042 at 15:30. Channel 8 has 20 error counts, the rest channels don’t have any errors. IVVDC current is 415 mA, temperature is 35 C.
Testing new optoboards:
6040 - 415 mA, optical power OK, stop errors test ok
6036 - 412 mA, optical power OK, stop errors test ok
6045 - 410 mA, VCSEL2 has lower optical power (ch 8 - 15 have ~600 mA), stop errors test ok
5036 - 387 mA, optical power OK, stop errors test ok
Starting long ran test again with the same board (6042) at 16:10 - have permanent error counts at channels 8...
12/02/2014
Channel 8 has 17 error counts at 11:25 am.
12/01/2014
Channel 8 has 15 error counts, the last count was on Saturday, November 30, at ~2:30 pm
Some items were moved around the test setup, that might have affected the error counts (?)
11/25/2014
Run goes smoothly, no error counts in any channel yet
11/17/2014
Run goes smoothly, no error counts in any channel yet
11/14/2014
The run goes smoothly, no error counts appeared at 10:15 am
11/13/2014
Updated the labview code to have stop error test run permanently. Started long run using IBL optoboard 6042 at 10:02 am
11/10/2014
Using board 6042 for a long run test (~1 week)
Before the start of the run:
6042 - 410 mA, optical power OK, stop errors test ok
Temperature after ~15 mins of running is 35 C.
10/29/2014
IBL boards used in SR1 tests:
6047 - Slot 10, DBM test
6022 - Slot 5
6002 - Slot 4
6000 - Slot 2, has broken black fiber connector for VCSEL1
6005 - Slot 1
6047 - 409mA, optical power OK, stop errors test ok
09/18/2014
6042 - 414m, optical power OK, stop errors test ok
09/15/2014
4004 - 330 mA, lower optical power in VCSEL2 (~1300 uW), stop error test is OK
4082- 386 mA, Optical powers test OK, stop error test is OK
09/09/2014
Re-testing problematic boards
4016 - VCSEL1 has no optical power, VCSEL2 has very low power (~70 uW), IVVDC ~320 mA
4082 - 381 mA, error counts test OK, optical powers test OK
4004 - 389 mA, error counts test OK, optical powers test OK -- While removing, the VCSEL2 connector got broken (probably too short pin on the removal tool -- this board has a thick aluminium connector, too thick for this tool)
6004 - error counts test OK, optical powers test OK
B12002 - 376 mA, error counts bad on Doric channel 5, VCSEL channel 0, 7. VCSEL 1 has no optical power on channel 0, 1.
26/08/2014
Testing new IBL boards
6022- 403 mA, error counts test OK, optical powers test OK
6035- 382 mA, error counts test OK, optical powers test OK
old D-board:
4042- 367 mA, error counts test OK, optical powers test OK
Boards available in SR1:
D-boards: 4117, 4240, 4209, 4262, 4305, 4308, 4307, 4309, 4313, 4303, 4304, 4302, 4314, 4310, 4312, 4315, 4112 , 4306, 4294, 4297, 4300, 4301, 4299, 4296, 4290, 4286, 4293, 4005, 4042, 4027, 4011, 4085, 4055, 4012, 4018, 4015, 4013, 4017, 4019 - total 39
B-boards: 5065, 5064, 5021, 5004, 5012
IBL: 6046, 6055, 6056, 6057, 6054, 6051, 6052
Not tested: 4054, 4176, 5006, 5040 (bad based on the NSQP_Optoboard_QA) + 2 IBL boards from Siinn
8/18/2014
Installing board 6047 for the DBM test (slot 7 of the optobox)
8/6/2014
Testing IBL board 6042 (request from Marcello)
6042 - 406 mA, error counts test OK, optical powers OK
8/5/2014
6053 installed in A slot 14 6040 broken. webpage updated
7/18/2014
boards being taken down to the pit: 6049, 6051
- 6049 inserted, 6051 returned to SR1 cabinet
7/8/2014
boards broken by IBL test team - 6022 - 6035
list of IBL boards in the pit:
6025 - A side slot 1
6023 - A side slot 2
6024 - A side slot 3
6028 - A side slot 4
6029 - A side slot 5
6030 - A side slot 6
6031 - A side slot 7
6032 - A side slot 8
6033 - A side slot 9
6034 - A side slot 10
6036 - A side slot 11
6038 - A side slot 12
6039 - A side slot 13
6040 - A side slot 14
6041 - A side slot 15
6007 - C side slot 1
6008 - C side slot 2
6009 - C side slot 3
6010 - C side slot 4
6011 - C side slot 5
6012 - C side slot 6
6013 - C side slot 7
6014 - C side slot 8
6015 - C side slot 9
6017 - C side slot 10
6018 - C side slot 11
6019 - C side slot 12
6020 - C side slot 13
6021 - C side slot 14
6027 - C side slot 15
6/23/2014
30 IBL boards packed and ready to go down to the pit
6/03/2014
Testing IBL boards delivered by Shane
6049 - 413 mA, error counts test OK, optical powers OK
6051 - 416 mA, error counts test OK, optical powers OK
6054 - 415 mA, error counts test OK, optical powers OK
6057 - 407 mA, error counts test OK, optical powers OK
6055 - 416 mA, error counts test OK, optical powers OK
6056 - 412 mA, error counts test OK, optical powers OK
6053 - 411 mA, error counts test OK, optical powers OK
6052 - 412 mA, error counts test OK, optical powers OK
5/15/2014
IBL board 6004 is given to Martin for the IBL optobox tests in the pit.
4/15/2014
Reception test for some boards
4151 - 389mA - all channels no errors - optical powers are fine. replacing this board in the pit fixed the problem with one module (I believe that it was module 6)
6002 - VCSEL1 has lower optical power (~800-900 uW), but should be fine for the tests in SR1. Error counts test is OK. The board is given to Martin.
5012 - Optical power OK, Stop error OK
4/8
IBL guys are breaking opto-boards carolos gave me 6022 which now has a broken VCSEL2 and 6002 which he says has no PIN current. We need to check / fix these. Also we need to do an IBL inventory and I need to come back to install IBL.
4/1
No reception test recorded for 5048: running now
5048: 385 mA, error counts test OK, optical powers OK
No reception test recorded for 4245: running now
4245: 378 mA, error counts test OK, optical powers OK
5036 has too much hysol to fit into the opto-box
3/31
6003 given to carolos for stave 7 and 8
6002 given to carolos for stave 7 and 8
6035 given to carolos for stave 7 and 8
6026 given to me by IBL, carolos it is broken
please retest 4151 - it had a flaky module in C side FT14
notice 6003 and 6035 sitting out on the table and not packed properlyy. Don’t use them unless absolutely necessary
03/24/2014
Retesting:
4112 - 388 mA, error counts test OK, optical powers OK
4301 - 389 mA, error counts test OK, optical powers OK
Note: 4112 was used in tests in the cavern. It will be placed in Box 1 in the cabinet in SR1.
03/20/2014
Retested board 5024: one module in one link has no error-free region
- scan #40576 (note: had vcsel 2 ribbon attached to top vcsel due to ribbon issues)
03/19/2014
5024 needs to be re-scanned
FT10 opto-boards moved to the pit
D-boards in SR1 divided into boxes:
Box 1: 4005-4103 (38)
Box 2: 4104-4151 (45)
Box 3: 4152-4208 (54)
Box 4: 4210-4244 (35)
Box 5: 4245-4301 (54)
Box 6: 4302-4315 (13)
03/18/2014
Reception test:
4055 - 353mA, error counts test OK, optical powers OK (VCSEL1 has lower optical power, ~1200-1500 uW, but it’s ok) - This board has low IVVDC, I list it as bad from now on
2D-scan:
4033 - scan #40549 -- all ok
4085 - scan #40550 -- all ok
4115 - scan #40551 -- all ok
4156 - scan #40553 -- all ok
4169 - scan #40554 -- all ok
4223 - scan #40556 -- all ok
4238 - scan #40559 -- all ok
4239 - scan #40562 -- all ok
Boards that will go to the pit tomorrow... FT10 opto-box is first to have ER bundles, opto-boards needed:
Box 1 - 0 B boards
23 D boards
1 spare
4028
4035
4036
4037
4039
4040
4041
4044
4045
4046
4047
4052
4053
4056
4057
4059
4060
4061
4062
4065
4066
4067
4068
Box 2 - 5 B boards
17 D boards
2 spare
5000
5001
5008
5009
5010
4069
4070
4071
4072
4073
4074
4075
4076
4077
4078
4079
4080
4081
4083
4084
4086
4087
2D scans:
5039 - scan #40517 -- all ok
5058 - scan #40519 -- all ok
5056 - scan #40520 -- all ok
5060 - scan #40521 -- all ok
5059 - scan #40526 -- all ok
5065 - scan #40534 -- all ok
5064 - scan #40539 -- all ok
5062 - scan #40540 -- all ok
5019 - scan #40547 -- all ok (one module looks slightly small due to ribbon problem)
5044 - scan #40548 -- all ok
Boards to give to Shane:
Box 1:
4005-4009, 4011-4015, 4017-4019,4022, 4024, 4027, 4028, 4030, 4032, 4035-4037, 4039, 4040-4042, 4044-4047, 4052, 4053, 4055-4057, 4059-4062, 4064-4068
Box 2:
4069-4081, 4083-4092, 4094-4111, 4113-4125
03/18/2014
4071 - scan #40453 -- all ok
4083 - scan #40456 -- all ok
4075 - scan #40457 -- all ok
4067 - scan #40458 -- all ok
4055 - scan #40460 -- all ok
4061 - scan #40461 -- all ok
4074 - scan #40462 -- all ok
4068 - scan #40464 -- all ok
4062 - scan #40465 -- all ok
4069 - scan #40466 -- all ok
4170 - scan #40467 -- all ok
4057 - scan #40468 -- all ok
4059 - scan #40469 -- all ok
4065 - scan #40471 -- all ok
4179 - scan #40473 -- all ok
4171 - scan #40475 -- all ok
4084 - scan #40476 -- all ok
4053 - scan #40478 -- all ok
4175 - scan #40480 -- all ok
4162 - scan #40481 -- all ok
4083 - scan #40482 -- all ok
4165 - scan #40484 -- all ok
4072 - scan #40485 -- all ok
4079 - scan #40487 -- all ok
4068 - scan #40488 -- all ok
4070 - scan #40490 -- all ok
4086 - scan #40492 -- all ok
4073 - scan #40493 -- all ok
4078 - scan #40494 -- all ok
4081 - scan #40495 -- all ok
4076 - scan #40496 -- all ok
4080 - scan #40497 -- all ok
4030F-scan #40498 -- all ok
4168 - scan #40501 -- all ok
4172 - scan #40502 -- all ok
4173 - scan #40503 -- all ok
4177 - scan #40505 -- all ok
4178 - scan #40509 -- all ok
4166 - scan #40511 -- all ok
4164 - scan #40513 -- all ok
4167 - scan #40514 -- all ok
Retest:
4012 - scan #40516 -- all ok
03/17/2014
4260 - scan #40393 -- all ok
4258 - scan #40394 -- all ok
4254 - scan #40396 -- all ok
4240 - scan #40398 -- all ok
4249 - scan #40399 -- all ok
4271 - scan #40400 -- all ok
4014 - scan #40402 -- all ok
4009 - scan #40404 -- all ok
4013 - scan #40406 -- all ok
4006 - scan #40408 -- all ok
4022 - scan #40411 -- problem with link 2: doing reception test
- reception test fine after using nitrogen to blow off laser
- scan #40418 -- all ok
4027 - scan #40413 -- all ok
4024 - scan #40416 -- all ok
4005 - scan #40419 -- all ok
4019 - scan #40423 -- problem with last channel of link 2: small area
- reception test: everything ok
- scan #40429 -- all ok
4060 - scan #40424 -- all ok
4008 - scan #40426 -- all ok
4274 - scan #40431 -- all ok
4007 - scan #40432 -- all ok
4017 - scan #40433 -- all ok
4018 - scan #40435 -- all ok
4016 - scan #40438 -- problems in link 2: doing reception test
- reception test: power low in vcsel 2, IVVDC ~315 mA
- visual inspection: one or more channels not emitting light
4015 - scan #40441 -- all ok
4012 - scan #40447 -- problems with link 1 (may be ribbon related)
- reception test: everything ok
- Will retest tomorrow
4011 - scan #40449 -- all ok
03/14/2014
Jens and Karolos requested boards for the test system: giving them 4002, 4003, 4082, 5023, 5003
Reception tests:
4314 - 387 mA, error counts test OK, optical powers OK
4313 - 385 mA, error counts test OK, optical powers OK
4315 - 386 mA, error counts test OK, optical powers OK
5062 - 383 mA, error counts test OK, optical powers OK
5065 - 387 mA, error counts test OK, optical powers OK
5064 - 384 mA, error counts test OK, optical powers OK
2D scans:
4233 - scan #40347 -- all ok
4270 - scan #40348 -- all ok
4253 - scan #40350 -- all ok
4276 - scan #40351 -- all ok
4268 - scan #40353 -- all ok
4272 - scan #40355 -- all ok
4257 - scan #40356 -- all ok
4315 - scan #40357 -- all ok
4313 - scan #40359 -- all ok
4314 - scan #40361 -- all ok
4056R-scan #40362 -- all ok
4039R-scan #40363 -- all ok
4036R-scan #40364 -- all ok
4035R-scan #40365 -- all ok
4261 - scan #40366 -- all ok
4262 - scan #40368 -- all ok
4264 - scan #40369 -- all ok
4277 - scan #40374 -- problem with link 2
- redid reception test, all ok
- scan #40378 -- all ok
4278 - scan #40375 -- all ok
4256 - scan #40376 -- all ok
4275 - scan #40379 -- all ok
4259 - scan #40380 -- all ok
4263 - scan #40381 -- all ok
4242 - scan #40382 -- all ok
4267 - scan #40383 -- all ok
4241 - scan #40384 -- all ok
4266 - scan #40385 -- all ok
4273 - scan #40386 -- all ok
4255 - scan #40387 -- all ok
4265 - scan #40389 -- all ok
03/13/2014
2D scans:
4301 - scan #40311 -- all ok
4302 - scan #40312 -- all ok
4296 - scan #40313 -- all ok
4304 - scan #40314 -- all ok
4306 - scan #40315 -- all ok
4281 - scan #40316 -- all ok
4283 - scan #40317 -- all ok
4289 - scan #40318 -- all ok
4288 - scan #40320 -- all ok
4290 - scan #40321 -- all ok
4292 - scan #40322 -- all ok
4101 - scan #40323 -- all ok
4280 - scan #40324 -- all ok
4285 - scan #40327 -- all ok
4295 - scan #40328 -- all ok
4312 - scan #40329 -- all ok
4297 - scan #40330 -- all ok
4298 - scan #40331 -- all ok
4064F-scan #40333 -- all ok
4308 - scan #40334 -- all ok
4310 - scan #40335 -- all ok
4286 - scan #40336 -- all ok
4282 - scan #40337 -- all ok
4174 - scan #40338 -- all ok
4303 - scan #40339 -- all ok
4309 - scan #40340 -- all ok
4294 - scan #40341 -- all ok
4307 - scan #40342 -- all ok
4305 - scan #40343 -- all ok
4293 - scan #40344 -- all ok
4299 - scan #40345 -- all ok
4300 - scan #40346 -- all ok
03/11/2014
Shane looked at the optical signal from 5024: board is fine.
03/10/2014
2D scans:
4103 - scan #40242 -- all ok
4114 - scan #40243 -- all ok
4110 - scan #40245 -- all ok
4091 - scan #40247 -- all ok
4158 - scan #40248 -- all ok
4089 - scan #40249 -- all ok
4149 - scan #40250 -- all ok
4151 - scan #40251 -- all ok
4105 - scan #40252 -- all ok
4102 - scan #40253 -- all ok
4148 - scan #40254 -- all ok
4147 - scan #40255 -- all ok
4093 - scan #40256 -- all ok
4125 - scan #40257 -- all ok
4096 - scan #40258 -- all ok
4106 - scan #40259 -- all ok
4066 - scan #40261 -- all ok
4152 - scan #40264 -- all ok
4113 - scan #40265 -- all ok
4143 - scan #40267 -- all ok
4077 - scan #40268 -- all ok
4139 - scan #40269 -- all ok
4097 - scan #40270 -- all ok
4160 - scan #40271 -- all ok
4154 - scan #40272 -- all ok
4108 - scan #40273 -- all ok
4155 - scan #40274 -- all ok
4146 - scan #40276 -- all ok
4098 - scan #40279 -- all ok
4109 - scan #40281 -- all ok
4104 - scan #40282 -- all ok
4157 - scan #40283 -- all ok
4140 - scan #40284 -- all ok
4092 - scan #40286 -- all ok
4116 - scan #40287 -- all ok
4153 - scan #40290 -- problem with last channel in both links
4099 - scan #40293 -- problem with last channel in both links
→ may have had temporary module problem
4095 - scan #40294 -- all ok
-->redid reception test on 4153, everything ok: retesting
4099 - scan #40295 -- all ok
4153 - scan #40296 -- all ok
4111 - scan #40297 -- all ok
4141 - scan #40298 -- all ok
4279 - scan #40299 -- all ok
4284 - scan #40300 -- all ok
4291 - scan #40301 -- all ok
4032F-scan #40304 -- all ok
03/07/2014
2D scans:
4236 - scan #40182 -- all ok
4248 - scan #40184 -- all ok
4227 - scan #40185 -- all ok
4199 - scan #40186 -- all ok
4195 - scan #40187 -- all ok
4221 - scan #40188 -- all ok
4213 - scan #40189 -- all ok
4211 - scan #40190 -- all ok
4245 - scan #40191 -- all ok
4198 - scan #40192 -- all ok
4231 - scan #40194 -- all ok
4161 - scan #40195 -- all ok
4229 - scan #40196 -- all ok
4243 - scan #40197 -- all ok
4197 - scan #40199 -- all ok
4216 - scan #40200 -- all ok
4252 - scan #40201 -- all ok
4247 - scan #40202 -- all ok
4250 - scan #40203 -- all ok
4203 - scan #40204 -- all ok
4217 - scan #40206 -- all ok
4233 - scan #40207 -- all ok
4249 - scan #40208 -- all ok
4226 - scan #40210 -- all ok
4230 - scan #40211 -- all ok
4235 - scan #40212 -- all ok
4244 - scan #40215 -- all ok
4220 - scan #40216 -- all ok
4246 - scan #40217 -- all ok
4210 - scan #40218 -- all ok
4214 - scan #40219 -- all ok
4219 - scan #40220 -- all ok
4212 - scan #40221 -- all ok
4228 - scan #40223 -- all ok
4222 - scan #40224 -- all ok
4234 - scan #40225 -- all ok
4215 - scan #40226 -- all ok
4256 - scan #40227 -- all ok
4088 - scan #40228 -- all ok
4120 - scan #40229 -- all ok
4100 - scan #40230 -- all ok
4145 - scan #40231 -- all ok
4159 - scan #40232 -- all ok
4090 - scan #40233 -- all ok
4105 - scan #40234 -- all ok
4142 - scan #40235 -- all ok
4087 - scan #40236 -- all ok
4117 - scan #40237 -- all ok
4150 - scan #40238 -- all ok
4107 - scan #40239 -- all ok
4124 - scan #40241 -- all ok
03/06/2014
2D scans:
4218 - scan #40174 -- all ok
4224 - scan #40175 -- all ok
4225 - scan #40176 -- all ok
4232 - scan #40177 -- all ok
4237 - scan #40179 -- all ok
03/04/2014
Board 4200 was dropped when removing from optobox 4200, redid reception test:
4200 - 386 mA, error counts test OK, optical powers OK
4209 was dropped when removing from the optobox: connector for vcsel 1 is cracked.
2D scans:
4200 - scan #40111 -- all ok
4193 - scan #40112 -- all ok
4192 - scan #40113 -- all ok
4206 - scan #40114 -- all ok
4183 - scan #40115 -- all ok
4188 - scan #40116 -- all ok
4190 - scan #40117 -- all ok
4209 - scan #40119 -- all ok
4186 - scan #40120 -- all ok
4045F-scan #40121 -- all ok
4047F-scan #40122 -- all ok
4046F-scan #40123 -- all ok
4189 - scan #40125 -- all ok
4187 - scan #40126 -- all ok
4042F-scan #40127 -- all ok
4040 - scan #40128 -- all ok
4052 - scan #40129 -- all ok
4044 - scan #40134 -- all ok
4041F-scan #40135 -- all ok
4205 - scan #40136 -- all ok
4204 - scan #40137 -- all ok
4028 - scan #40138 -- all ok
4181 - scan #40139 -- all ok
4131 - scan #40140 -- all ok
4208 - scan #40141 -- all ok
4191 - scan #40142 -- all ok
4184 - scan #40143 -- all ok
4037F-scan #40144 -- all ok
4202 - scan #40146 -- all ok
4203 - scan #40147 -- all ok
4201 - scan #40148 -- all ok
4185 - scan #40149 -- all ok
4207 - scan #40150 -- all ok
4180 - scan #40152 -- all ok
4194 - scan #40153 -- all ok
4133 - scan #40154 -- all ok
4118 - scan #40155 -- all ok
4128 - scan #40156 -- all ok
4129 - scan #40157 -- all ok
4182 - scan #40158 -- all ok
4121 - scan #40159 -- all ok
4138 - scan #40160 -- all ok
4135 - scan #40161 -- all ok
4132 - scan #40162 -- all ok
4137 - scan #40163 -- all ok
4123 - scan #40164 -- all ok
4122 - scan #40166 -- all ok
4127 - scan #40168 -- all ok
4134 - scan #40169 -- all ok
4130 - scan #40170 -- all ok
4119 - scan #40171 -- all ok
4126 - scan #40173 -- all ok
02/26/2014
Optobox needs to be re-adjusted to be able to fit the optoboards
Shane took boards 4082 and 5003 for adjusting.
Other boards given to Rusty on Jan 24 are still in use for optobox production.
============================
02/25/2014
Reception tests for boards brought by Shane:
4310 - 385 mA, error counts test OK, optical powers OK
4309 - 387 mA, error counts test OK, optical powers OK
4295 - 390 mA, error counts test OK, optical powers OK
4292 - 386 mA, error counts test OK, optical powers OK
4302 - 387 mA, error counts test OK, optical powers OK
4294 - 388 mA, error counts test OK, optical powers OK
4301 - 393 mA, error counts test OK, optical powers OK
4312 - 388 mA, error counts test OK, optical powers OK
4299 - 390 mA, error counts test OK, optical powers OK
4307 - 387 mA, error counts test OK, optical powers OK
4297 - 386 mA, error counts test OK, optical powers OK
4296 - 388 mA, error counts test OK, optical powers OK
4306 - 385 mA, error counts test OK, optical powers OK
4304 - 383 mA, error counts test OK, optical powers OK
4303 - 395 mA, error counts test OK, optical powers OK
4308 - 385 mA, error counts test OK, optical powers OK
4298 - 389 mA, error counts test OK, optical powers OK
4300 - 382 mA, error counts test OK, optical powers OK
4305 - 391 mA, error counts test OK, optical powers OK
4293 - 387 mA, error counts test OK, optical powers OK
5024 - 370 mA, cannot remove errors in one channel of vcsel 2, optical powers OK
Problem: attempted to use new optobox to perform 2D scan of board 5057. 80-pin connector on both board and ER bundle had pin on connector bent upon insertion.
02/07/2014
Testing new boards brought by Harris:
5058 - 385 mA, error counts test OK, optical powers OK
5056 - 382 mA, error counts test OK, optical powers OK
5059 - 384 mA, error counts test OK, optical powers OK
5057 - 381 mA, error counts test OK, optical powers OK
5039 - 388 mA, error counts test OK, optical powers OK
5060 - 380 mA, error counts test OK, optical powers OK
4279 - 388 mA, error counts test OK, optical powers OK
4101 - 387 mA, error counts test OK, optical powers OK
4282 - 385 mA, error counts test OK, optical powers OK
4174 - 381 mA, error counts test OK, optical powers OK
4280 - 387 mA, error counts test OK, optical powers OK
4290 - 378 mA, error counts test OK, optical powers OK
4291 - 385 mA, error counts test OK, optical powers OK
4286 - 384 mA, error counts test OK, optical powers OK
4289 - 388 mA, error counts test OK, optical powers OK
4283 - 391 mA, error counts test OK, optical powers OK
4281 - 384 mA, error counts test OK, optical powers OK
4285 - 384 mA, error counts test OK, optical powers OK
4284 - 385 mA, error counts test OK, optical powers OK
4032 - 387 mA, error counts test OK, optical powers OK
4064 - 386 mA, error counts test OK, optical powers OK
4288 - 385 mA, error counts test OK, optical powers OK
02/05/2014
4017 - 379 mA, error counts test OK, optical powers OK
03/02/2014
Steven got board 4112 for the pixel tests in the pit.
==========================
01/31/2014
Board 4112 is given to Karolos for the toothpix tests (reception test is good)
4112 - scan 40059 (line 1, link 1 has problem)
5024 - scan 40060 -- all OK!
5034 - scan 40062 -- all OK!
5036 - scan 40063 and 40065 -- all OK!! -- 3D scan - 40064
reception test:
5024 - 371 mA, Channel 12 (fiber space) has permanent errors ~1 per sec at delay 13
4085 - 383 mA, all ok.
===========================
01/30/2014
2D scans::
5050 - scan #40043 -- all ok
5024 - cannot get correct IVdc
5037 - scan #40053 -- all ok (after cleaning optical fiber)
5034 - cannot get correct IVdc (was tested OK yesterday?)
5036 - scan #40057 - links 5 and 7 have errors. Reception test is normal.
===========================
01/29/2014
2D scans:
5024 - scans 40010 and 40009 when the board was connected to slots 13 and 14 correspondingly, showed the last channel (bottom-right on the plots) with no error-free region.
Reception test for 5024 - 372 mA, optical test OK, ch 12 (in fiber space) has errors
Using tested before board to find a good slot
5004 - scan 40011 is for slot 13 and 40012 for slot 14 (both are OK)
2D scans:
5038 - scan #40017 -- all ok
5046 - scan #40018 -- all ok
5028 - scan #40019 -- all ok
5025 - scan #40020 -- all ok
5047 - scan #40021 -- all ok
5035 - scan #40022 -- all ok
5049 - scan #40023 -- all ok
5052 - scan #40024 -- all ok
5053 - scan #40025 -- all ok
5036 - scan #40026 -- problem with last channel in link 1 and 2
5034 - scan #40030 -- all ok
5055 - scan #40031 -- all ok
5041 - scan #40032 -- all ok
5027 - scan #40033 -- all ok
5051 - scan #40034 -- all ok
5045 - scan #40035 -- all ok
5037 - scan #40037 -- problem with one channel in link 1 and 2
5043 - scan #40038 -- all ok
5030- scan #40040 -- all ok
5034 - not possible to turn on (VIset is low for both slot 13 and slot 14)
===============================
01/28/2014
2D-scans:
5042 - scan #39996 -- channel 3 has no error free region.
The panel doesn’t show correctly the IPin current, and the board IVVDC iis not set properly after turning on the board. Moved to Slot 13 - works fine (except still no IPin current displayed)
5033 - scan #40000 -- all OK
Checked the PP2 cable with Kerstin -seems to be fine
Slot 14 of the otobox has bent pin.
5024 - scan #40005 -- 2 last channels are not good and #40008 - only one channels is not good.
When slot 13 is used, 3D scan is not possible, because it’s not possible to change the VIset
================================
1/27/2014
Reception test:
4267 - 390 mA, error counts test OK, optical powers OK
4261 - 385 mA, error counts test OK, optical powers OK
4258 - 386 mA, error counts test OK, optical powers OK
4260 - 382 mA, error counts test OK, optical powers OK
4256 - 380 mA, error counts test OK, optical powers OK
4262 - 386 mA, error counts test OK, optical powers OK
4277 - 385 mA, error counts test OK, optical powers OK
4254 - 382 mA, error counts test OK, optical powers OK
4275 - 387 mA, error counts test OK, optical powers OK
4264 - 385 mA, error counts test OK, optical powers OK
4263 - 385 mA, error counts test OK, optical powers OK
4278 - 387 mA, error counts test OK, optical powers OK
4035R - 384 mA, error counts test OK, optical powers OK
4039R - 363 mA, error counts test OK, optical powers OK
4259 - 386 mA, error counts test OK, optical powers OK
4036R - 384 mA, error counts test OK, optical powers OK
4056R - 380 mA, error counts test OK, optical powers OK
4276 - 381 mA, error counts test OK, optical powers OK
4033R - 392 mA, error counts test OK, optical powers low in VCSEL 1 (1300-1400 uW)
4255 - 380 mA, error counts test OK, optical powers OK
4242 - 378 mA, error counts test OK, optical powers OK
4270 - 388 mA, error counts test OK, optical power OK
4239 - 386 mA, error counts test OK, optical power OK
4273 - 387 mA, error counts test OK, optical power OK
4241 - 387 mA, error counts test OK, optical power OK
4274 - 380 mA, error counts test OK, optical power OK
4265 - 392 mA, error counts test OK, optical power OK
4266 - 388 mA, error counts test OK, optical power OK
4268 - 390 mA, error counts test OK, optical power OK
4257 - 382 mA, error counts test OK, optical power OK
4253 - 386 mA, error counts test OK, optical power OK
4272 - 387 mA, error counts test OK, optical power OK
4240 - 391 mA, error counts test OK, optical power OK
4271 - 386 mA, error counts test OK, optical power OK
4238 - 385 mA, error counts test OK, optical power OK
4033R -- retest: VCSEL 1 still low (1200-1400 uW)
5050 -- redid reception test, error counts test OK, optical powers OK
5042 -- no power from VCSEL 1, channel 3
1/25/2014
Reception tests for boards brought by Harris:
4258 - 382 mA, error counts test OK
→ Had to stop, was having trouble getting optical power test to run. Will look at the setup more closely Monday.
01/24/2014
Gave 5020 to Harris to take back to OSU.
Reception test for B-boards:
5050 - 384 mA, error counts test OK, optical power OK
5042 - 380 mA, channel 8 - permanent errors for all delays and no normal signal on oscilloscope, channel 3 has 0 optical power
B-boards that were previously used in nsqp tests: 5003, 5020, x
New boards to give to Rusty: 4163, 5040, 4054, 6071, 5005, 4023, 4025, 4176, 4038, 5006, 6068, 5061, 6070, 6069.
-- 4 IBL, 4 B-type, 6 D-type
Worked with Jens and found that there was a problem with one of the read-out connectors, which was likely causing some of our issues with previous b-board scans.
2D-scans:
5023 - scan #39967 -- all ok
5026 - scan #39968 -- all ok
5018 - scan #39973 -- all ok
5020 - no temperature readout and visible damage to pin connector
5004 - scan #39975 -- all ok
5001 - scan #39977 -- all ok
5029 - scan #39978 -- all ok
retest: 5013 - scan #39979 -- all ok
5048 - scan #39980 -- all ok
5042 - scan #39982 -- no error free region for two readouts (did 3D scan)
5031 - scan #39983 -- all ok
5050 - scan #39987 -- no error free region for two readouts (did 3D scan)
5054 - scan #39988 -- all ok
01/21/2014
Giving boards to Rusty for use in aligning parts for optobox assembly:
boards -- 4082, 5003, B12002, B12005, 4003, 4002, 4112, 4001, 4004, 5004
- just kidding, giving broken boards from Harris
Retesting boards from yesterday: Jens pointed out that module currents were not always correct on start-up.
5021 - scan #39920 -- all ok
5011 - scan #39925 -- all ok
5012 - scan #39926 -- all ok
5008 - scan #39927 -- all ok
Jens is changing RX plug at the BOC due to channel 6 narrow error-free region
5013 - lack of error-free region in one channel: Jens suspects the optical power from the channel may be too high.
5014- scan #39940 -- all ok
================================================
01/20/2014
2D scans:
5000 - scan #39906 -- all ok
5008 - scan #39907 : L2_B27_S2_A7_M5A -- no error free region
5021 - scan #39908: L2_B27_S2_A7_M2A -- no error free region
5017 - scan #39909 -- all ok
5011 - scan #39910: L2_B27_S2_A7_M6A, L2_B27_S2_A7_M3A -- no error free region
5022 - scan #39911 -- all ok
5010 - scan #39912 -- all ok
5016 - scan #39913 -- all ok
5009 - scan #39914 -- all ok
5012 - scan #39915: L2_B27_S2_A7_M3A -- no error free region
-- talked to Tayfun: need to be able to change VIset to properly test boards for error-free region
01/16/2014
Making 2D scans for the B-boards
5003 - fine
==================================
01/15/2014
IBL board 6037 got VCSEL2 connector broken.
6022 and 6045 plan to give to Daniel. Connection test is fine.
Board 6003 and 6004 are used in toothpix test.
==================================
01/10/2014
Re-testing 2 optoboards
4213 - 384 mA, error counts test OK, optical powers test OK
4196 - 381 mA, optical powers test OK, VCSEL1 channel 2 has error counts for all delay, even after cleaning with dry air. No evidence for dust visible in microscope.
===================================
1/8/2014
4228 - 384 mA, error counts test OK, optical powers test OK
4246 - 375 mA, error counts test OK, optical powers test OK
-- NOTE: board was dropped being removed from box before testing
4229 - 388 mA, error counts test OK, optical powers test OK
4227 - 381 mA, error counts test OK, optical powers test OK
4248 - 380 mA, error counts and clock errors in doric channel 3, optical powers test OK
4252 - 382 mA, error counts test OK, optical powers test OK
4195 - 385 mA, error counts test OK, optical powers test OK
4199 - 384 mA, error counts test OK, optical powers test OK
4236 - 380 mA, error counts test OK, optical powers test OK
4214 - 385 mA, error counts test OK, optical powers test OK
4231 - 386 mA, error counts test OK, optical powers low and variable
4247 - 382 mA, error counts test OK, optical powers test OK
4221 - 384 mA, error counts test OK, optical powers test OK
4223 - 380 mA, error counts test OK, optical powers test OK
4250 - 381 mA, error counts test OK, optical powers test OK
4249 - 379 mA, error counts test OK, optical powers test OK
4237 - 383 mA, error counts test OK, optical powers test OK
4230 - 386 mA, error counts test OK, optical powers test OK
4219 - 382 mA, error counts test OK, optical powers test OK
4220 - 387 mA, error counts test OK, optical powers test OK
4198 - 382 mA, error counts test OK, optical powers test lowish (1100-1500 uW)
4235 - 383 mA, error counts test OK, optical powers test OK
4224 - 385 mA, error counts test OK, optical powers test OK
4243 - 385 mA, error counts test OK, optical powers test OK
4212 - 383 mA, error counts test OK, optical powers test OK
4235 - 382 mA, error counts test OK, optical powers test OK
4222 - 382 mA, error counts test OK, optical powers test OK
4234 - 385 mA, error counts test OK, optical powers test OK
4296 - 387 mA, errors in vcsel 1, ch 2, optical powers test OK
4244 - 383 mA, error counts test OK, optical powers test OK
4213 - 384 mA, error counts test OK, vcsel 2 powers slightly low (1100-1500 uW)
4211 - 380 mA, error counts test OK, optical powers test OK
4210 - 387 mA, error counts test OK, optical powers test OK
4226 - 388 mA, error counts test OK, optical powers test OK
4233 - 384 mA, error counts test OK, optical powers test OK
4217 - 385 mA, error counts test OK, optical powers test OK
4215 - 382 mA, error counts test OK, optical powers test OK
4216 - 380 mA, error counts test OK, optical powers test OK
4218 - 385 mA, error counts test OK, optical powers test OK
4225 - 382 mA, error counts test OK, optical powers test OK
4232 - 384 mA, error counts test OK, optical powers test OK
4197 - 382 mA, error counts test OK, optical powers test OK
retest:
4248 - 380 mA, error counts test OK, optical powers test OK
4231 - 384 mA, error counts test OK, optical powers test OK
4198 - 380 mA, error counts test OK, optical powers test OK
4196 - 382 mA, errors in VCSEL 1, ch 2, optical powers test OK
======================================
12/20/2013
Re-testing and sending back to OSU with KK the following boards:
4032, 4064, 5039.
======================================
12/19/2013
Continue testing new boards
4028 - 385 mA, error counts test OK, optical powers test OK
4028 - 379 mA, error counts test OK, optical powers test OK
4032 - 393 mA, VCSEL1 channels have no optical power (40 uW) and produce error counts.
4042 - 362 mA, error counts test OK, optical powers test OK
4030 - 385 mA, error counts test OK, channel 7 has lower optical power (~1200 uW)
4202 - 388 mA, error counts test OK, optical powers test OK
4204 - 387 mA, error counts test OK, optical powers test OK
4203 - 382 mA, error counts test OK, optical powers test OK
4201 - 387 mA, error counts test OK, optical powers test OK
4200 - 387 mA, error counts test OK, optical powers test OK
================================
12/18/2013
One of the IBL boards without optical power recorded:
6035 - 405 mA, error counts test OK, optical powers test OK
Testing new boards delivered by KK:
4180 - 384 mA, error counts test OK, optical powers test OK
4183 - 382 mA, error counts test OK, optical powers test OK
4181 - 384 mA, error counts test OK, optical powers test OK
4184 - 380 mA, error counts test OK, optical powers test OK
4045 - 386 mA, error counts test OK, optical powers test OK
4186 - 384 mA, error counts test OK, optical powers test OK
4188 - 379 mA, error counts test OK, optical powers test OK
4187 - 384 mA, error counts test OK, optical powers test OK
4182 - 385 mA, error counts test OK, optical powers test OK
4189 - 376 mA, error counts test OK, optical powers test OK
4209 - 387 mA, error counts test OK, optical powers test OK
4206 - 382 mA, error counts test OK, optical powers test OK
4207 - 381 mA, error counts test OK, optical powers test OK
4205 - 385 mA, error counts test OK, optical powers test OK
4208 - 380 mA, error counts test OK, optical powers test OK
4190 - 384 mA, error counts test OK, optical powers test OK
4191 - 385 mA, error counts test OK, optical powers test OK
4192 - 382 mA, error counts test OK, optical powers test OK
4193 - 382 mA, error counts test OK, optical powers test OK
4194 - 383 mA, error counts test OK, optical powers test OK
4046 - 387 mA, error counts test OK, optical powers test OK
4044 - 382 mA, error counts test OK, optical powers test OK
4041 - 380 mA, error counts test OK, optical powers test OK
4047 - 379 mA, error counts test OK, optical powers test OK
4037 - 388 mA, error counts test OK, optical powers test OK
4131 - 390 mA, error counts test OK, optical powers test OK
4053 - 380 mA, error counts test OK, optical power low in Ch0 (~1300uW)
4052 - 385 mA, error counts test OK, optical powers test OK
4064 - 385 mA, error counts test OK, optical power low in VCSEL 2 (~600-1300uW) all channels
4185 - 382 mA, error counts test OK, optical powers test OK
====================================
12/17/2013
4066 - 382 mA, error counts test OK, optical powers OK
5039 - 387 mA, error counts test OK, vcsel2 has lower optical power (down to 1000uW)
Gave 4 IBL 6037, 6003, 6035, 6026 to Daniel for the IBL
==========================================
12/16/2013
Testing boards requested by Yi
5023 - 387 mA, error counts test OK, optical powers OK
5026 - 382 mA, error counts test OK, optical powers OK
4161 - 386 mA, error counts test OK, optical powers OK
5003 - 382 mA, error counts test OK, optical powers OK (slightly low vcsel 1, ch 3: ~1400 uW)
5004 - 385 mA, error counts test OK, optical powers OK
==========================================
11/29/2013
Took the optoboards used in the connection test back to the SR1 (boards 5003 and 5023; 4082 and 4112), as well as board 5004.
Testing board B12005 (used in toothpix test)
B12005 - 375 mA, error counts test OK, optical powers OK
==========================================
11/08/2013
Testing a new batch delivered by Harris
4177 - 386 mA, error counts test OK, optical powers OK
4178 - 387 mA, error counts test OK, optical powers OK
4171 - 387 mA, error counts test OK, optical powers OK
4175 - 388 mA, error counts test OK, optical powers OK
4174 - 382 mA, error counts test OK, channel 10 has lower optical power (1100 uW)
4170 - 378 mA, error counts test OK, optical powers OK
4168 - 375 mA, error counts test OK, optical powers OK
4179 - 386 mA, error counts test OK, optical powers OK
4161 - 386 mA, error counts test OK, optical powers OK
4172 - 384 mA, error counts test OK, optical powers OK
4166 - 380 mA, error counts test OK, optical powers OK
4162 - 392 mA, error counts test OK, optical powers OK
4173 - 379 mA, error counts test OK, optical powers OK
4164 - 383 mA, error counts test OK, optical powers OK
4169 - 381 mA, error counts test OK, optical powers OK
4167 - 384 mA, error counts test OK, optical powers OK
4165 - 385 mA, error counts test OK, optical powers OK
re-testing 4174:
4174 - 385 mA, error counts test OK, optical powers OK
=======================================
11/07/2013
Re-testing again “problematic” boards from the last batch
4139 - 372 mA, error counts test OK, optical powers OK (required 4 test before optical power was OK)
4125 - 384 mA, error counts test OK, optical powers OK (required 3 test before optical power was OK)
4120 - 381 mA, error counts test OK, optical powers OK (required 4 test before optical power was OK)
4124 - 387 mA, error counts test OK, optical powers OK
-------------------------------------------
Testing 5 random older boards, from the 1st batch.
4013 - 383 mA, error counts test OK, optical powers OK
4009 - 369 mA, error counts test OK, optical powers OK
4019 - 395 mA, error counts test OK, optical powers OK
4001 - 320 mA, error counts from VCSEL2, optical power is absent for all channels from VCSEL2 (ch 7-13) - This board was not supposed to be used in installation.
4060 - 385 mA, error counts test OK, optical powers OK
----------------
4137 is not at CERN
----------------
=====================================
11/05/2013
Testing new batch of D-boards delivered by Richard.
4127 - 387 mA, error counts test OK, optical powers OK
4130 - 384 mA, error counts test OK, optical powers OK
4132 - 385 mA, error counts test OK, optical powers OK
4121 - 377 mA, error counts test OK, optical powers OK
4125 - 383 mA, error counts test OK, optical powers OK - iset (?)
4134 - 381 mA, error counts test OK, optical powers OK
4129 - 386 mA, error counts test OK, optical powers OK
4122 - 385 mA, error counts test OK, optical powers OK
4126 - 383 mA, error counts test OK, optical powers OK
4137 - 382 mA, error counts test OK, optical powers OK
4123 - 394 mA, error counts test OK, optical powers OK
4128 - 386 mA, error counts test OK, optical powers OK
4138 - 384 mA, error counts test OK, optical powers OK
4135 - 384 mA, error counts test OK, optical powers OK
4133 - 391 mA, error counts test OK, optical powers OK
4119 - 377 mA, error counts test OK, optical powers OK
4120 - 381 mA, error counts test OK, VCSEL1 has low optical powers (~400 uW)
4139 - 369 mA, Channels 0, 1, 7-13 have error counts, lower optical power in VCSEL1 and practically no light in VCSEL2 (40 -50 uW).
4124 -mA, same problems...
re-testing previously tested board:
4138 - 384 mA, error counts test OK, optical powers OK
4118 - 381 mA, error counts test OK, optical powers OK
-------------------------------------
Testing boards taken by KK
4148 - 389 mA, error counts test OK, optical powers OK
4143 - 382 mA, error counts test OK, optical powers OK
4142 - 382 mA, error counts test OK, optical powers OK
4149 - 385 mA, error counts test OK, optical powers OK
4147 - 382 mA, error counts test OK, optical powers OK
4141 - 379 mA, error counts test OK, optical powers OK
4140 - 383 mA, error counts test OK, optical powers OK
4146 - 381 mA, error counts test OK, optical powers OK
4152 - 386 mA, error counts test OK, optical powers OK
4145 - 379 mA, error counts test OK, optical powers OK
4156 - 383 mA, error counts test OK, optical powers OK
4158 - 382 mA, error counts test OK, optical powers OK
4150 - 380 mA, error counts test OK, optical powers OK
4157 - 387 mA, error counts test OK, optical powers OK
4154 - 382 mA, error counts test OK, optical powers OK
4153 - 380 mA, error counts test OK, optical powers OK
4159 - 388 mA, error counts test OK, optical powers OK
4151 - 387 mA, error counts test OK, optical powers OK
4160 - 388 mA, error counts test OK, optical powers OK
4155 - 374 mA, error counts test OK, optical powers OK
-----------------------
Re-testing “problematic” boards
4124 - 382 mA, Channels 7, 8, 9, 10, 11, 12, 13 (VCSEL2) - show error counts for all delays. VCSEL1 channnels have normal power, VCSEL2 - very low (~40 uW).
4139 - 372 mA, error counts test OK, optical powers OK (a little lower in VSEL1, ~1500 uW)
4120 - 383 mA, error counts test OK, optical powers is lower for all VCSEL1 channels (~800 uW)
4125 - 380 mA, error counts test OK, optical powers OK
===============================================================
10/31/2013
Testing new problematic board 4064. Tayfun claims it has readout problem with one of the VCSEL channels, and this problem is not stable, sometimes it disappears in the same setup.
To replace this optoboard, I gave him another one from the newest batch - #4112.
4064 - 385 mA, Channels 7, 8, 9, 10 have lower optical power (~1300).
VCSEL1 connector is not stable. The black optical fiber connector is shaking, and if I change a little fiber’s position, channel 0 starts having error counts. This is also visible in oscilloscope (some error counts curves, plus the shape of the signal is a little different). If I press the cable down, the errors disappear. This doesn’t happen with DORIC or VCSEL2 (the fiber connectors are glued strongly). Only VDC channel 0 has this issue.
====================================================
10/29/2013
Testing the rest of optoboards
4100 - 382 mA, error counts test OK, optical powers OK
4116 - 389 mA, error counts test OK, optical powers OK
4091 - 378 mA, error counts test OK, optical powers OK
4102 - 383 mA, error counts test OK, optical powers OK
4093 - 374 mA, error counts test OK, optical powers OK
4099 - 391 mA, error counts test OK, optical powers OK
4087 - 382 mA, error counts test OK, optical powers OK
4092 - 366 mA, error counts test OK, optical powers OK
4095 - 382 mA, error counts test OK, optical powers OK
4096 - 388 mA, error counts test OK, optical powers OK
4088 - 380 mA, error counts test OK, optical powers OK
4117 - 386 mA, error counts test OK, optical powers OK
4108 - 387 mA, error counts test OK, optical powers OK
4098 - 380 mA, error counts test OK, optical powers OK
4112 - 381 mA, error counts test OK, optical powers OK
Re-testing problematic one:
4101 - 387 mA, channels 0, 5, 6 and 11 have error counts, VCSEL1 has lower optical power for all channels (120-190 uW).
=============================================
10/28/2013
31 new optoboards recieved.
5014 - 377 mA, error counts test OK, optical powers OK
4101 - 383 mA, error counts from channel 0 and channel 6, the optical powers from VCSEL1 are very low (~100 uW)
4114 - 382 mA, error counts test OK, optical powers OK
4089 - 373 mA, error counts test OK, optical powers OK
4109 - 382 mA, error counts test OK, optical powers OK
4104 - 383 mA, error counts test OK, optical powers OK
4090 - 385 mA, error counts test OK, optical powers OK
4106 - 388 mA, error counts test OK, optical powers OK
4113 - 384 mA, error counts test OK, optical powers OK
4103 - 386 mA, error counts test OK, optical powers OK
4097 - 378 mA, error counts test OK, optical powers OK
4105 - 385 mA, error counts test OK, optical powers OK
4111 - 382 mA, error counts test OK, optical powers OK
4107 - 380 mA, error counts test OK, optical powers OK
4110 - 382 mA, error counts test OK, optical powers OK
4115 - 384 mA, error counts test OK, optical powers OK
====================================================
Board 5009
Iset Iset readout IVVDC VVDC Ipin RetIpin1 RetIpi2
0 0.0415 242
0.18 0.174 274
0.2 0.198 276
0.3 0.297 284
0.5 0.508 300
1.0 0.98 330
1.5 1.52 363
2.0 2.0 384
0 0.064 244
=========================================
10/01/2013
4086 - IVVDC = 379 mA, error counts test OK, optical powers are OK
4065 - IVVDC = 380 mA, error counts test OK, optical powers are OK
4068 - IVVDC = 379 mA, error counts test OK, optical powers are OK
4067 - IVVDC = 382 mA, error counts test OK, optical powers are OK
4070 - IVVDC = 381 mA, error counts test OK, optical powers are OK
4069 - IVVDC = 378 mA, error counts test OK, optical powers are OK
4071 - IVVDC = 382 mA, error counts test OK, optical powers are OK
4074 - IVVDC = 382 mA, error counts test OK, optical powers are OK
4073 - IVVDC = 380 mA, error counts test OK, optical powers are OK
4076 - IVVDC = 382 mA, error counts test OK, optical powers are OK
4072 - IVVDC = 384 mA, error counts test OK, optical powers are OK
4066 - IVVDC = 380 mA, error counts test OK, optical powers are OK
4078 - IVVDC = 381 mA, error counts test OK, optical powers are OK
4083 - IVVDC = 382 mA, error counts test OK, optical powers are OK
4084 - IVVDC = 381 mA, error counts test OK, optical powers are OK
4085 - IVVDC = 383 mA, error counts test OK, optical powers are OK
4079 - IVVDC = 380 mA, error counts test OK, optical powers are OK
4075 - IVVDC = 383 mA, error counts test OK, optical powers are OK
4077 - IVVDC = 375 mA, error counts test OK, optical powers are OK
4080 - IVVDC = 378 mA, error counts test OK, optical powers are OK
4081 - IVVDC = 380 mA, error counts test OK, optical powers are OK
4082 - IVVDC = 380 mA, error counts test OK, optical powers are OK
-----------------------
Test for Jense with different Iset
Board 4082
Iset Iset readout IVVDC VVDC Ipin RetIpin1 RetIpi2
2mA 2.0 mA 380 mA
1.5mA 1.55 361
1 mA 1.01 327 2.47 957u 2.31u 784n
0.5mA 0.51 294 2.46 957u 2.19u 784n
0.3 0.295 279
0.2 0.193 270
0.18 0.150 267
Optical powers:
4082 10/1/2013 4:26:16 PM 2.329938E+3 2.286111E+3 2.656759E+3 2.713150E+3 2.655241E+3 2.279792E+3 2.964535E+3 2.700578E+3 2.396416E+3 2.532687E+3 2.321496E+3 3.460211E+3 3.260914E+3 3.529040E+3
4082 10/1/2013 4:53:24 PM 2.024853E+3 1.965242E+3 2.337016E+3 2.346183E+3 2.346413E+3 2.074671E+3 2.523415E+3 2.420435E+3 2.123268E+3 2.261934E+3 1.974468E+3 3.086992E+3 2.918742E+3 3.120443E+3
4082 10/1/2013 4:56:58 PM 1.609547E+3 1.556852E+3 1.840109E+3 1.833377E+3 1.863864E+3 1.647335E+3 1.991165E+3 1.888984E+3 1.667032E+3 1.787104E+3 1.529102E+3 2.514233E+3 2.330850E+3 2.342409E+3
4082 10/1/2013 5:00:45 PM 1.147661E+3 1.079050E+3 1.257029E+3 1.252718E+3 1.294645E+3 1.171373E+3 1.370495E+3 1.288109E+3 1.145208E+3 1.240851E+3 1.067001E+3 1.759573E+3 1.644118E+3 1.587433E+3
4082 10/1/2013 5:06:46 PM 9.107603E+2 8.310951E+2 9.657699E+2 9.578681E+2 9.988612E+2 9.235483E+2 1.033463E+3 9.847561E+2 8.689996E+2 9.672294E+2 8.413191E+2 1.318447E+3 1.244057E+3 1.221025E+3
4082 10/1/2013 5:10:44 PM 7.755834E+2 7.109530E+2 8.218378E+2 8.168309E+2 8.471703E+2 7.848321E+2 8.770189E+2 8.301635E+2 7.366775E+2 8.308303E+2 7.115549E+2 1.104030E+3 1.042813E+3 1.043175E+3
4082 10/1/2013 5:13:15 PM 7.056554E+2 6.486815E+2 7.520301E+2 7.478205E+2 7.731759E+2 7.190693E+2 8.046789E+2 7.561894E+2 6.749289E+2 7.594802E+2 6.536049E+2 9.925164E+2 9.662078E+2 9.307597E+2
-----------------------
Re-tested board 5014 - This time channels 7 is OK, there is signal and no error counts. Optical power in channels 0,1 and 3 still lower than usual (1230, 680 and 1000 uW correspondingly). Optical inspection with the microscope didn’t find any dirt or dust around VCSELs.
========================================
09/30/2013
5000 - IVVDC = 379 mA, error counts test OK, optical powers are OK
5010 - IVVDC = 383 mA, error counts test OK, optical powers are OK
5016 - IVVDC = 379 mA, error counts test OK, optical powers are OK
5013 - IVVDC = 378 mA, error counts test OK, optical powers are OK
5008 - IVVDC = 380 mA, error counts test OK, optical powers OK (CH 2 a little low, ~1480)
5021 - IVVDC = 382 mA, error counts test OK, optical powers OK
5018 - IVVDC = 382 mA, error counts test OK, optical powers OK
5017 - IVVDC = 381 mA, error counts test OK, optical powers OK
5022 - IVVDC = 383 mA, error counts test OK, optical powers OK
5001 - IVVDC = 380 mA, error counts test OK, optical powers OK (CH 8 a little low ~ 1488)
5020 - IVVDC = 380 mA, error counts test OK, optical powers OK
5011 - IVVDC = 385 mA, error counts test OK, optical powers OK
5009 - IVVDC = 383 mA, error counts test OK, optical powers OK
5014 - IVVDC = 378 mA, optical powers bad in CH 0, 1, 3; VDC errors in CH 7 (no oscilloscope signal)
5012 - IVVDC = 380 mA, error counts test OK, optical powers OK
5019 - IVVDC = 382 mA, error counts test OK, optical powers OK
=========================================
09/19/2013
5033 - IVVDC = 380 mA, error counts test OK, optical powers are OK
5031 - IVVDC = 380 mA, error counts test OK, optical powers are OK
5027 - IVVDC = 382 mA, error counts test OK, optical powers are OK
5035 - IVVDC = 379 mA, error counts test OK, optical powers are OK
5041 - IVVDC = 385 mA, error counts test OK, optical powers are OK
5053 - IVVDC = 382 mA, error counts test OK, optical powers are OK
5051 - IVVDC = 381 mA, error counts test OK, optical powers are OK
5034 - IVVDC = 382 mA, error counts test OK, optical powers are OK
5036 - IVVDC = 382 mA, error counts test OK, optical powers are OK
5037 - IVVDC = 379 mA, error counts test OK, optical powers are OK
5044 - IVVDC = 358 mA, error counts test OK, optical powers are a little low
5052 - IVVDC = 382 mA, error counts test OK, optical powers are OK
5029 - IVVDC = 381 mA, error counts test OK, optical powers are OK
5039 - IVVDC = 383 mA, error counts test OK, optical powers are low in channels 10,11,12
5055 - IVVDC = 385 mA, error counts test OK, optical powers are OK
5046 - IVVDC = 386 mA, error counts test OK, optical powers are OK
5030 - IVVDC = 389 mA, error counts test OK, optical powers are OK
5047 - IVVDC = 381 mA, error counts test OK, optical powers are OK
6035 - IVVDC = 407 mA, error counts test is OK, optical powers are OK
6026 - IVVDC = 403 mA, error counts test is OK, optical powers are OK
=======================================
09/17/2013
5054 - IVVDC = 383 mA, error counts test is OK, optical powers are OK
=======================================
09/16/2013
Testing B-boards.
5024 - IVVDC = 367 mA, error counts test is OK, optical powers are OK
5042 - IVVDC = 382 mA, error counts test is OK, optical powers are OK
5028 - IVVDC = 375 mA, error counts test is OK, optical powers are OK
5043 - IVVDC = 382 mA, error counts test is OK, optical powers are OK
5050 - IVVDC = 382 mA, error counts test is OK, optical powers are OK
5049 - IVVDC = 387 mA, error counts test is OK, optical powers are OK
5045 - IVVDC = 380 mA, error counts test is OK, optical powers are OK
5025 - IVVDC = 385mA, error counts test is OK, optical powers are OK (2nd VCSEL is lower ~1500 uW)
5038 - IVVDC = 371 mA, error counts test is OK, optical powers are OK
4048- IVVDC = 383 mA, error counts test is OK, optical powers are OK
2 old IBLs:
6004 - 382 mA, error counts test is OK, optical powers are OK (a little lower, especially the second VCSEL, ~1500 uW)
6003 - 390 mA, error counts test is OK, optical powers are OK (the first VSCEL has lower optical power ~1200 uW)
1 old D-type board
4003 - 318 mA, VCSEL1 has sporadically disappearing signal. Optical power is zero for the VCSEL1 and low (~1100) for VCSEL2
4046 - 385 mA, error counts test is OK, optical powers are OK
====================================================
09/13/2013
Testing new optoboards
6033 - IVVDC = 405 mA, error counts test is OK, optical powers are OK
6039 - IVVDC = 408 mA, error counts test is OK, optical powers are OK
6037 - IVVDC = 407 mA, error counts test is OK, optical powers are OK
6040 - IVVDC = 412 mA, error counts test is OK, optical powers are OK
6036 - IVVDC = 402 mA, error counts test is OK, optical powers are OK
6045 - IVVDC = 407 mA, error counts test is OK, optical powers are OK
6031 - IVVDC = 403 mA, error counts test is OK, optical powers are OK
6012 - IVVDC = 416 mA, error counts test is OK, optical powers are OK
6018 - IVVDC = 400 mA, error counts test is OK, optical powers are OK
6011 - IVVDC = 415 mA, error counts test is OK, optical powers are OK
6007 - IVVDC = 406 mA, error counts test is OK, optical powers are OK
6023 - IVVDC = 412 mA, error counts test is OK, optical powers are OK
6017 - IVVDC = 400 mA, error counts test is OK, optical powers are OK
6019 - IVVDC = 401 mA, error counts test is OK, optical powers are OK
6008 - IVVDC = 412 mA, error counts test is OK, optical powers are OK
6025 - IVVDC = 409 mA, error counts test is OK, optical powers are OK
6020 - IVVDC = 407 mA ,error counts test is OK, optical powers are OK
6009 - IVVDC = 411 mA, error counts test is OK, optical powers are OK
6015 - IVVDC = 412 mA, error counts test is OK, optical powers are OK
6013 - IVVDC = 415 mA, error counts test is OK, optical powers are OK
6021 - IVVDC = 409 mA, error counts test is OK, optical powers are OK
6014 - IVVDC = 410 mA, error counts test is OK, optical powers are OK
6010 - IVVDC = 407 mA, error counts test is OK, optical powers are OK
======================================
09/12/2013
Testing new optoboards
6022 - IVVDC = 405 mA, error counts test is OK, optical powers are OK
6029 - IVVDC = 408 mA, error counts test is OK, optical powers are OK
6028 - IVVDC = 407 mA, error counts test is OK, optical powers are OK
6042 - IVVDC = 409 mA, error counts test is OK, optical powers are OK
6046 - IVVDC = 405 mA, error counts test is OK, optical powers are OK
6048 - IVVDC = 410 mA, error counts test is OK, optical powers are OK
6027 - IVVDC = 408 mA, error counts test is OK, optical powers are OK
6044 - IVVDC = 411 mA, error counts test is OK, optical powers are OK
6034 - IVVDC = 403 mA, error counts test is OK, optical powers are OK
6041 - IVVDC = 406 mA, error counts test is OK, optical powers are OK
6030 - IVVDC = 410 mA, error counts test is OK, optical powers are OK
6032 - IVVDC = 406 mA, error counts test is OK, optical powers are OK
6024 - IVVDC = 411 mA, error counts test is OK, optical powers are OK
6047 - IVVDC = 414 mA, error counts test is OK, optical powers are OK
============================================
09/10/2013
New patch from Jason is almost fine. There is no signal readout from channel 7 (both optical power and oscilloscope). Also, DORIC shows all data errors, I need to set “all 50%” to be able to set zero errors for all channels.
IBL test seems to be fine except DORIC test with Stop Errors: it’s not displayed.
09/05/2013
Optoboards used in nSQP test:
5023, 5003, 4032, 4064
Optobox Slots : 2, 4, 6, 9
08/08/2013
4 D and 4 B-boards will be used in nSQP test:
B-boards: 5020, 5003, 5004, 5015
D-boards: 4042, 4056, 4064, 4032. 4035
Replaced the old B-board B12005 with the new on 5003.
Turning off the power for all the optoboards. Running for ~25 hours without any problems.
============================================================
08/06/2013
A new set of optoboards to be connected to the optobox
4055, 4056, 4035, 4036, 4052, 4053, 4028, 4030
Re-tested 4051 with the new LabView code, using correct version of hep015a_nsqp_rev1.bit file. Now the software works fine. Checked this with the B--type board as well (5016) - works fine with this one too.
Tested a new optical cable, from the official production. Doesn’t seems to have any problems, mapping is correct.
Retesting 2 previously problematic optoboards
5010 - 386 mA, all channels no errors, optical power is OK
5013 - 376 mA, DORIC channel 6 has both Clk and Data errors, optical power is OK
Optoboard from the optobox had 20 mA Iset (at least was shown in DCS - not clear if the optoboard has received the full current), the optoboard is from Slot1, the edge of the optobox
4042 - 362 mA, errors ar ok, optical power is OK
An accident: while removing board number 4040 from the Slot6 of the optobox (very tight!), the connector of VCSEL1 got damaged. The board got accelerated and flight out from the box, falling on the floor. The optical fiber still can get into VCSEL connector, test shows no problem with the optical power or error counts for both DORIC and VCSELs.
======================================================
08/05/2013
Testing optoboard 4051 which was connected to Slot 11 of the optobox. This slot have received the inverted ISET polarity signal.
4051 - 362 mA, DORIC - all channels have Clk errors, channels 1,3 and 5 have a wrong signal shape (2 times shorter), channels 1,2,3,4,5,6 (all except channel 0) have Data error problem.
VCSEL - channels 8 and 9 have VDC Data errors problem, despite the shape looks fine.
Optical power is OK.
Testing optoboard 4032 which was connected to Slot 4 of the optobox
4032 - 388 mA, DORIC - all channels have Clk errors, channel 1,3 and 5 have a wrong signal shape (2 times shorter), channels 1,2,3,4,5,6 (all except channel 0) have Data error problem. Optical power is Ok
For the reference, testing another D-board
4056 - 375 mA, has the same issues as the other tested channels. Definitely a problem with the software.
----------------------------------------------------------------------
Changed to the old version of LabView code.
4056 - is OK
4032 - 388 mA, DORIC channels 2 and 6 have Data error counts, despite the shapes look good and no error count signals are visible on the oscilloscope. VCSEL is good.
4051 - 354 mA, DORIC is OK, VCSEL is OK.
=============================================
07/30/2013
Using new VI patch (CERN_nsqp_IBL_testbench)
5020 - VCSEL channels 11, 12 and 13 always have errors for all delays, they also have a wrong signal shape. Optical power is OK for all channels.
5016 - VCSEL channels 11, 12 and 13 always have errors for all delays, they also have a wrong signal shape. Optical power is OK for all channels.
5003 - VCSEL channels 11, 12 and 13 always have errors for all delays, they also have a wrong signal shape. Optical power is OK for all channels.
5009 - VCSEL channels 11, 12 and 13 always have errors for all delays, they also have a wrong signal shape. Optical power is OK for all channels.
-----------------------------------------------------------------------------------
Optoboards for the optobox test:
D-boards - 4064, 4060, 4051, 4047, 4039, 4044, 4037, 4040, 4032, 4032, 4062, 4042
=========================================================
07/27/2013 Testing new shipped boards
Moved the equipment from the radiation room to the clean room in SR1.
Checking one of the previously tested boards to make sure the equipment is working
4062 - 378mA, all channels no errors, optical power OK.
----------------------------------------
5018 - 381mA, all channels no errors, optical power OK.
5022 - 379mA, all channels no errors, optical power OK.
2 observed issues with the b-boards:
1) On the B boards DORIC channel 5 and 7 have 100% correlated error counts.
2) When changing delay for VCSEL channel 8 or 9, the error counts in DORIC start going on (both click and data errors) for all DORIC channels. Opto reset doesn’t help.
4033 - 386mA, all channels no errors, optical power OK.
5020 - 379mA, all channels no errors, optical power OK.
5016 - 380mA, all channels no errors, optical power OK.
5017 - 382mA, all channels no errors, optical power OK.
5020 - 378mA, all channels no errors, optical power OK.
5023 - 379mA, all channels no errors, optical power OK.
4042 - 378mA, all channels no errors, optical power OK.
4042 - 370mA, all channels no errors, optical power OK.
5015 - 378mA, all channels no errors, optical power OK.
5021 - 386mA, all channels no errors, optical power OK.
5019 - 383mA, all channels no errors, optical power OK.
5014 - 379mA, all channels no errors, channel 1 and 3 have lower optical power (641 and 970 uW).
========================================================
07/15/2013 Testing new B-boards
----------------------------------------------------------------------------------
Previous D-board 4062, retested - 386mA, all channels no errors, optical power OK
5013 - 373mA, DORIC channel 6 shows strange signal and always counts error (both data errors for any delay value, and clk errors), optical power OK
5003 - 378mA, all channels no errors, optical power OK
5011 - 382mA, all channels no errors, optical power OK
5004 - 381mA, all channels no errors, optical power OK
5008 - 376mA, all channels no errors, optical power OK
5009 - 379mA, all channels no errors, optical power OK
5010 - 375mA, channel 9 VCEL has no signal (all three: oscilloscope, error counter and optical power).
5012 - 378mA, all channels no errors, optical power OK
==========================================================
07/06/2013 - retaking data for problematic boards
4039 - Optical power test seems to give a normal result (no asymmetry between two VCSELs)
4033 - the same optical power as tested yesterday (first 7 channels have lower power). VSEL2 connector got broken when I was disconnecting optical fiber... 2nd connector broken this way...
4055 - the same optical power test result as yesterday (first 7 channels have lower power).
4053 - the same optical power test result as yesterday (first 7 channels have lower power).
4030 - the same optical power test result as yesterday (last 7 channels have lower power).
4062 - the same optical power test result as yesterday (channel 2 has a low optical power, ~860 uW)
5000 - The board is, probably, fine. There is a problem with the channel mapping (probably with the LabView macro -- or with the chip?). Channels for VCSEL2 are shifted by 2 when trying to set the correct delay for Stop Errors test. The response matrix is following:
Channel where Channel which
delay is changed responds to the change
10 8
11 9
12 10
13 11
14 12
15 13
5001 - The same issue as for 5000: the channels for VCSEL2 are shifted by 2.
4034 - Completely normal board, no problems with channel 11, as it was yesterday.
===============================
07/05/2013 - new set of boards
ISET = 2mA for all boards
4033 - 391mA - all channels no errors, optical power is lower for the first 7 channels (channels 0-6, the power is ~1800-1900 uW)
4061 - 383mA, all channels no errors, optical power OK
4034 - 386mA, VDC channel 11 always has errors; optical power OK, except channel 11, where the power is 4811 uW.
4060 - 384mA, all channels no errors, optical power OK
4045 - 385mA, all channels no errors, optical power OK
4046 - 381mA, all channels no errors, optical power OK
4042 - PIN connector is mechanically broken.
4044 - 382mA, all channels no errors, optical power OK
4055 - 351mA, all channels no errors, optical power is lower for the first 7 channels (channels 0-6, the power is ~1300-1500 uW)
4056 - 383mA, all channels no errors, optical power OK
4064 - 386mA, all channels no errors, optical power OK
4062 - 378mA, all channels no errors, optical power OK, except channel 2, where the power is 820 uW
4032 - 384mA, all channels no errors, optical power OK
4031 - 386mA, all channels no errors, optical power OK
4059 - 382mA, all channels no errors, optical power OK
4057 - 380mA, all channels no errors, optical power OK
4035 - 383mA, all channels no errors, optical power OK
4036 - 384mA, all channels no errors, optical power OK
4052 - 384mA, all channels no errors, optical power OK
4053 - 373mA, all channels no errors, optical power is lower for the first 7 channels (channels 0-6, the power is ~1500-1800 uW)
4051 - 358mA, all channels no errors, optical power OK
4047 - 374mA, all channels no errors, optical power OK
4030 - 380mA, all channels no errors, optical power is lower for the first 7 channels (channels 0-6, the power is ~1000-1500 uW)
4028 - 388mA, all channels no errors, optical power OK
4040 - 376mA, all channels no errors, optical power OK
4041 - 374mA, all channels no errors, optical power OK - VCSEL Input2 connector got broken when the optical cable was removed.
4039 - 357mA, all channels no errors, optical power is lower for the last 7 channels (channels 7-13, the power is ~1500-1800 uW)
4037 - 381mA, all channels no errors, optical power OK
5001 - 382mA, all channels no errors, optical power OK
5000 - 378mA, channel 11 of VDC is not stable (spontaneously start counting error for some time), channel 13 seems OK on the scope, but not possible to set a delay with 0 errors; optical power OK
=======================================
6/4/2013
ISET = 2mA for all boards
4006 - 377mA - all channels no errors, optical power OK
4005 - 311mA - all channels no errors, optical power OK, 2nd VCSEL lower power (~1100) IVDD LOW!
4024 - 408mA - all channels no errors, optical power OK
4022 - 388mA - all channels no errors, optical power OK
4013 - 382mA - all channels no errors, optical power OK
4014 - 389mA - all channels no errors, optical power OK
4017 - 377mA - all channels no errors, optical power OK
4018 - 384mA - all channels no errors, optical power OK
4007 - 357mA - all channels no errors, optical power OK
4008 - 359mA - all channels no errors, optical power OK
4009 - 361mA - all channels no errors, optical power OK
4019 - 392mA - all channels no errors, optical power OK
4015 - 378mA - all channels no errors, optical power OK
4016 - 401mA - all channels no errors, optical power OK
4027 - 380mA - all channels no errors, optical power OK
4011 - 382mA - all channels no errors, optical power OK
4012 - 382mA - all channels no errors, optical power OK