www.rajdowe-haldy.pl  www.rallycomputer.com www.sparkelectronics.pl www.taksometry.pl

SHOP ➨: www.sklep.sparkelectronics.pl

 

Rally computer 3 +

Rally computer 3+. GPS *

User Manual.

Installation and configuration.

* Content marked [GPS] for versions with built-in GPS or an external device connected Garmin. Working with an external GPS module, such as the Garmin does not provide such precision as the built-in GPS.


Rally computer 3 +

Rally computer 3+. GPS *

User Manual.

Installation and configuration.

Description tripmeter

Purpose

functions.

Installation Instructions

Connection

View of the

LEDs

Engagement on / off the

Configuration

Calling the setup menu

first method.

second method.

configuration menu

Configuration distance measurement

calibration factor of the vehicle.

calibration factor - the measurement.

calibration factor - typing

selection of the calibration factor - only when a multi function k is turned

Use

Selection modes

Introduction TIMER time - the time counted from the set values

Waiting to start the measurement.

DISTANCE mode - a description of the function and purpose of

STAGE mode - a description of the function and purpose of

end of the measurement

mode DISTANCE

STAGE Mode

Continuation of measurements - DIST mode or STAGE.

Technical data and operating

Warranty


Description tripmeter

Purpose

tripmeter Computer Rally Series 3 + is a professional device for use in auto racing - flat, off-road and navigation. Flexibility in the use of blocks measuring allows you to adjust the measured parameters specific to each race.

Measurement results are presented on a super-bright LED displays red.

Aluminum waterproof housing provides protection against external factors. First-class electronics ensure reliable operation and high precision measurements.

Tripmeter service is implemented using a 3-button keypad, which buttons have permanently assigned most measurement functions.

Rally computer 3 + is used to measure the road, time, speed, voltage electricity network vehicle, and [GPS] course.

functions.


Installation Instructions

Attaching the

tripmeter install in a conspicuous place and allows seamless access to the front panel. For mounting brackets tripmeter are bolted to the sides of the housing. Do not remove the brackets that do not lead to a loss of containment device.

When connecting the power pay attention to the voltage source was reliable

andstable (providing a value between 8 to 30 V).

Tripmeter not mount in areas adversely affects the damage or misusing such action at the outlets air, areas exposed to mechanical damage and also in the possibility of causing interference safety of the vehicle, for example on air cushions,

NB. Turn off the device does not cut it completely from the power supply. We continue to draw current (reduced to a minimum). When the device is not in use, disconnect it from the vehicle wiring. This will prevent discharging the battery. Top install an external switch that disconnects the power supply unit in a complete way.

Connection

20140406_rc3plus_schemat_podlaczenia_en.JPG


Setup and manual

View of the

LEDs

TRIP - displayed on the screen is the function of the road a short

ODO - displayed on the screen is activated long way

TIMER - the screen displays the function timeru

STOP - is displayed on screen stopwatch function

GPS - GPS status, no light - no GPS on or off in the menu flashes - looking for GPS signal lights - Visibility more than 5 satellites

REP - odometer able repeater

RUN - up dimmed displays, odometer still works

Engagement on / off the

device does not have a power switch. After the power supply is ready for operation. The items unrelated to direct the work, with no tension on the cable yellow ("ignition") goes to sleep. You can connect the yellow wire to the power which will disable this functionality.

Upon power tripmeter:

on the odometer was turned off when not realized measurements - will activate the DIST mode that is where the main measurement is the measurementroad

of thewhen the odometer was off when the realized measurements (in any mode, and any measurement function) after reconnecting the power measurements will further continue

with the startup screen position odometer will turn off automatically after 1 minute. if the wire yellow designed to connect the ignition will not tension.

With each function by long press CLR (about 6 seconds) can lead to the appearance of the home screen and interrupt the measurement.

Exclusion tripmeter is possible only with the position of the home screen by long (12 sec.) continuously pressing the button F1z position ekrannu boot. During the off tripmeter after 7 sec. present the serial number and version of and then switched off.

Configuration

Note. Setting up a new tripmeter complies with the card settings included in the scope.

Calling the setup menu

to turn on the configuration menu should be:

first method.

  1. Bring to the appearance of the home screen that is ______ on all displays, by pressing the CLR button for 6 seconds. (If you see ______ it means that you are in the start screen and you skip this step)
  2. Turn off the power tripmeter
  3. Read this section carefully before powering tripmeter. After reconnecting the power on all displays immediately show up 888888 and then in the display window will display the currently selected calibration factor constant k of the vehicle. During this time, press the F1 key 3 times and then OK - they are just 4 seconds. When you do, wait and on the display Conf
  4. If you wait too long and starts to repeat the measurement point. 1 - 3

second method.

  1. Bring to the appearance of the home screen that is ______ on all displays, by pressing the CLR button for 6 seconds. (If you see ______ it means that you are in the start screen and you skip this  Press
  2. step)(not letting go of the previous year) in order CLR button, then F1, and then another OK (at the end of the operation will be held 3 buttons at once). As soon as you press the third button will reset the odometer
  3. onall displays immediately show up 888888 and then in the display window will display the currently selected calibration factor constant k of the vehicle. During this time, press the F1 key 3 times and then OK - they are just 4 seconds. When you do, wait and on the display Conf
  4. If you wait too long and starts to repeat the measurement point. 1 - 4

configuration menu

after menu move by pressing the F1 key to enter the function with

theOK button. , The change make by pressing F1 and confirm

with OK. Parameter change is confirmed by a flash of the display.

Exitparameter setting performed by pressing CLR. From the menu to the normal operating mode

also go out CLR button which will restart tripmeter, save

thesettings and start measuring mode.

Available settings are:

  1. Type - is displayed on the display Type - Select the type of behavior tripmeter
  1. MSTR - Master, working as a tripmeter
  2. Slave - Slave , work as a repeater
  1. units of measurement - is displayed on the display UNIT - selecting units which will be presented measurements of the road - miles and miles
  1. meter - metric
  2. imperial - imperial system (ny) or English
  1. pulses - the display shows the IMPS - dialing mode - of pulses road and only GPS or
  1. GPS-and-off- work with only the GPS system - measuring is done only from 5 km / h
  2. and-on - work using pulses obtained from the road car or an additional sensor and GPS system - this measurement provides the most accurate
  1. GPS - GPS signal source selection
  1. none - disable the GPS
  2. [GPS] int - work with internal GPS module
  3. call - work with an external GPS module
  1. GPS d - on / off GPS participate in calculating way
  1. off - odometer will work only with pulses from the wheels
  2. on - the GPS will support road charging
  1. Multi k - the display shows null k - activation work with multiple calibration coefficients
  1. on - working with multiple coefficients
  2. off - work with one factor

When all values ​​when we press the main branch of the CLR. Long beep and reset the tripmeter indicates the setting.

Configuration distance measurement

calibration factor of the vehicle.

This is the number of pulses counted from the vehicle corresponding to the crossing 1,000 m  

measured ratio can be:

calibration factor - the measurement.

metromierzu there is the possibility of measuring the number of pulses for the stretch of road of any length. To start the measurement must be in the position of the home screen, press and hold the OK button and then additionally press the F1 key. The appearance of the 0-values ​​confirms the launch function.

Now:

F1 resets the measured values ​​and immediately begin recounting

OK saves the measurement and passes to enter the preset number under which you save the calibration of the measured value (only when the Multi k is ON. When Multi k is set to OFF to save made will be given a default value and a window to enter the preset number will not show  Version

up)- Film: http://www.rajdowe-haldy.pl/wsparcie/video-instrukcje.html

calibration factor - typing

When the calibration factor is known it is possible to enter its value to the odometer. To start typing in a position to be the home screen, press and hold the OK button and then additionally press the CLR. The appearance of the 0-values ​​confirms the launch function.

Now:

F1 increases the value of the digit

OK pressed briefly digit moves to the left and allows you to enter the next digit (when typing a factor of more than 5 digits, when he first left digit will be off the screen light up all the dots to indicate the sytyacje)

OK pressed long remembers measurement and passes to enter the preset number under which you save the calibration of the measured value (only when the Multi k is ON. When Multi k is set to OFF to save will be made ​​under the default window and enter a number memory will not show  Version

up)- Film: http://www.rajdowe-haldy.pl/wsparcie/video-instrukcje.html

selection of the calibration factor - only when a multi function k is turned

to the calibration factor was active, select it from memory. Selecting the aspect ratio is stable - it will be used for calculation until you select a different value.  

To make a choice:

  1. Bring the appearance of the home screen that is ______ on all displays, by pressing the button for 6 seconds F. (if you see __ ____ it means that you are in the start screen and you skip this step)
  2. Press and hold the F1 as long as the string goes out DIST ie the ability to select the mode. Continue to hold down the F1
  3. for the help of the CLR button browse coefficient memory (momentary pause in pressing the CLR will show the value of the memory cell)
  4. When you find the factor by which you plan the measurement, release the F1 key

measurements will be continued by the new calibration factor.

Manufacturing method - Film: http://www.rajdowe-haldy.pl/wsparcie/video-instrukcje.html

Use

Selection modes

to choose from we have 2 options:

From the home screen press the F1 key. The window shows the name of the mode. Repeatedly press the F1 switch selectable modes. You accept the OK button.

Name mode

LEDMode

Application

Switching

DIST

MODE 4 blinking LEDs remain off. Each of these signals only its basic functionality.

When you need to measure and quickly delete the road a short TRIP

mode automatically switches from the start screen or you can turn on the measurements in this mode by pressing the F1 sequence and then pressing OK when the screen appears DIST.

STAGE

4 LEDs flash briefly indicating MODE. Each of them also signals its basic functions.

When you need to measure lap times Stopwatch

from the start screen, we can turn the measurements in this mode by pressing the F1 sequence and then pressing OK when the screen appears STAGE.

Introduction TIMER time - the time counted from the set values

​​after select any mode shows us in the display "_" and we have the opportunity to enter the TIMER time. When we do not want to type, press OK. When you want to type it using the arrows increment the value of the first digit, the OK button moves a digit to the left, enter the second digit, and so to the end until you enter all the values. CLR can erase what you typed in the event of an error, a long press CLR to exit the screen.

Note  

Waiting to start the measurement.

displays are flashing. The machine is waiting for you to press the F1 key on your keyboard which will start the measurement.

DISTANCE mode - a description of the function and purpose of

theF1 TRIP - clearing the way TRIP - (after starting changing their destiny and acts as a clearing calculating road). When the displays are presented other parameters, the first pressing F1 brings TRIP indication on the screen.

FUNCTION shows in sequence:

[gps] TRACK - course - shows the course if you have connected a GPS. In the first box to the left lit degree mark and the right value of the deviation from the north in degrees.

BAT - mains voltage of the vehicle - the first display field showing the letter U, which indicates that it is the tension, the right of the measured value

TIMER - the time remaining to the next TC - when introduced before the start time between PKC. If this is not the time from the start.

LEDs - when we are in the function of the arrow button changes the brightness.

Could lead to the total extinction displays and LEDs RUN inflammation. ATTENTION. When the odometer is blank is pressing any button to glow in the middle of clarity.

COR - allows the adjustment of ODO - press OK. and shows us the current value of the ODO. The F1 and CLR cause the addition or subtraction of 10 m to the ODO. After adjustment press OK. What will blink and save the adjusted value.

ODO - total road - LED lights ODO

SPEED - speed - For the first box on the left displays the letter S on the right indicate the current speed.

manner of - action movie mode DIST http://rajdowe -haldy.pl/wsparcie/video-instrukcje.html

STAGE mode - a description of the function and purpose of

theF1 STOP. - Start / stop charging STOPWATCH-time (after starting changing their destiny and acts as a start / stop time measurement). When the displays are presented other parameters, the first pressing F1 brings indication on the screen.

FUNCTION presented in the following order:

[gps] TRACK - course - shows the course if you have connected a GPS. In the first box to the left lit degree mark and the right value of the deviation from the north in degrees

BAT - mains voltage of the vehicle - the first display field showing the letter U, which indicates that it is the tension, the right of the measured value

TIMER - remaining until the next TC - when introduced before the start time between PKC. If this is not the time from the start.

LEDs - when we are in the function of the arrow button changes the brightness.

Could lead to the total extinction LED displays and inflammation RUN.UWAGA. When the odometer is blank is pressing any button to glow in the middle of clarity.

ODO - the road overall - LED lights ODO        

SPEED - speed - For the first box on the left displays the letter S on the right indicate the current speed.

Manner of - action movie mode STAGE http://rajdowe-haldy.pl/wsparcie/video-instrukcje.html

end of the measurement

mode DISTANCE

mode by pressing long finish OK by definitively concludes the opportunity to continue the measurement in this mode.

TIMER do not delete calculating and ODO. Screen appears indirect, consisting of the character "-".

STAGE Mode

After stopping time F1 button, and press the OK button a long time, finally finishing the possibility of continuing measurement in this mode.

Delete not charging timer and ODO. Screen appears indirect, consisting of the character "-".

Continuation of measurements - DIST mode or STAGE.

Then we can:


Technical data and operating


Warranty

Warranty is for a period of 60 months from the date of saledevice.Warranty

will be considered only in case of use of the product for its intended purpose. Warranty against defects in the product to prevent its further use as intended. Are not subject to warranty defects resulting from mechanical damage, alteration, normal wear items, etc.

The warranty is valid only with proof of purchase.

Name and Type: ........................................................

Date of sale : ..................................................

number: ...............................................

instructions

to download from the website: http:/ / rajdowe-haldy.pl/wsparcie/instrukcje.html

SPARKELECTRONICS Robert Skierski,

Office: 01-424 Warsaw, Al. Primate of the Millennium 78a, tel / fax: 022 836-24-51 

www.rajdowe-haldy.pl