www.rajdowe-haldy.pl  www.rallycomputer.com www.sparkelectronics.pl www.taksometry.pl

SHOP ➨: www.sklep.sparkelectronics.pl

Rally computer 7

Rally computer 7.GPS *

Rally computer 7.Regularity

Installation and configuration.

Instruction Manual.

* Content marked [GPS] only for versions with built-in GPS or an external device connected Garmin. Working with an external GPS module, such as the Garmin does not provide such precision as the built-in GPS.

Rally computer 7

Rally computer 7.GPS *

Rally computer 7.Regularity

Installation and configuration.

Descriptiontripmeter.

Purpose

Functions.

Mounting Instructions

Connection

displays.

LEDs

Switching on / off the

Configurationtripmeter.

Calling the setup menu

first method.

second method.

configuration menu

List of abbreviations measured parameters

Configuration distance measurement

calibration factor of the vehicle.

calibration factor - the measurement.

calibration factor - typing

selection of the calibration factor

Measurement configurationfuel

Factor fuel metering

Calibration - the measurement

calibration - typing

Operation

Selection modes

Countdown parameters of selected values

introduction of road overall - ODO

introduction of the section OS - TRIP

The introduction of time - Timer

Enter the start delay DELAY.

Countdown in days drive parameters regularity (Regularity)

parameters calculated and stored in the memory

list of parameters stored in the memory

Waiting for measurement start

Additional

measurements.functions (action key) - STAGE mode

Description of functions (action key) - disance mode

2).functions (action key) - Regularity mode

End measurements - viewing of the

DISTANCE mode

STAGE Mode

Regularity mode

Technical and operational

Warranty


Descriptiontripmeter.

Purpose

tripmeter Rally Computer 7 is a professional device for use in auto racing - flat, off-road and navigation.

Flexibility in the use of blocks measuring allows you to adjust the measured parameters specific to each race.

measurement results are presented on a super -bright LED displays red.

aluminum waterproof housing provides protection against external factors. First-class electronics ensure reliable operation and high precision measurements.

Tripmeter service is implemented using the 14-button keyboard in which the keys are permanently assigned key functions measuring or via an optional external resetter.

Rally computer 7 is used to measure the road, speed, time , fuel level in the voltage of the vehicle and [GPS] course. Measured parameters can be presented in different ways.

Functions.

installation and configuration.

Mounting Instructions

Mounting

tripmeter install in a conspicuous place and allows seamless access to the front panel. For mounting brackets tripmeter are bolted to the sides of the housing. Do not remove the brackets that do not lead to a loss of containment device.

When connecting the power pay attention to the voltage source was reliable

andstable (providing a value between 8 to 30 V).

Tripmeter not mount in areas adversely affects the damage or misusing such action at the outlets air, areas exposed to mechanical damage and also in the possibility of causing interference safety of the vehicle, for example on air cushions,

NB. Turn off the device does not cut it completely from the power supply. We continue to draw current (reduced to a minimum). When the device is not in use, disconnect it from the vehicle wiring. This will prevent discharging the battery. Top install an external switch that disconnects the power supply unit in a complete way.

Connection

20130402_rc7_schemat_xat.jpg


Setup and manual

View of the

rc7_gps_c_1000_xat.jpg

displays.

Tripmeter is equipped with 2 independent window displays, both equipped with the ability to display 6 digits.

LEDs

DIST - active DISTANCE. When blinking means that the mode is automatically started

STAGE - DISTANCE active. When blinking means that the mode is automatically started

LAP - lights up when you use the split function LAP TIME

GPS - indicates the status of the GPS - when flashing it means search signal when a steady light indicates the presence of a GPS signal when not lit indicates a malfunction

MEM. - Lights up when viewing memory measurements

RUN - lights up when the total extinction of the display as a sign that the work unit continues.

Switching on / off the

device does not have a power switch. After the power supply is ready for operation. The items unrelated to direct the work, with no tension on the cable yellow ("ignition") goes to sleep. You can connect the yellow wire to the power which will disable this functionality.

Upon power tripmeter:

on the odometer was turned off when not realized measurements - automatically starts DISTANCE mode measurements

of the tripmeter was off when the realized measurements (in any mode and any measurement function) is after reconnecting the power measurements will further continue

with the startup screen position odometer will turn off automatically after 1 minute. if the wire yellow designed to connect the ignition will not tension.

With each function by long press CLR (about 6 seconds) can lead to the appearance of the home screen and interrupt the measurement.

tripmeter can turn off (still flowing!) via long ( 12 sec.) continued pressing the [F2] from the position ekrannu boot. During the off tripmeter present serial number and version of the program, and then turns off. Then you can release the F1 key.

Configurationtripmeter.

NOTE  Setting up a new tripmeter complies with the card settings included in the scope.

Calling the setup menu

to turn on the configuration menu should be:

first method.

  1. Bring to the appearance of the home screen that is ______ on all displays, by pressing the CLR button for 6 seconds. (If you see ______ it means that you are in the start screen and you skip this step)
  2. Turn off the power tripmeter
  3. Read this section carefully before powering tripmeter. After reconnecting the power on all displays immediately show up 888888 and then in the display window will display the currently selected calibration factor constant k of the vehicle. During this time, press the F1 key 3 times and then OK - they are just 4 seconds. When you do, wait and on the display Conf
  4. If you wait too long and starts to repeat the measurement point. 1 - 3

second method.

  1. Bring to the appearance of the home screen that is ______ on all displays, by pressing the CLR button for 6 seconds. (If you see ______ it means that you are in the start screen and you skip this  Press
  2. step)(not letting go of the previous year) in the order of the buttons OK, then CLR (at the end of the operation will be holding two buttons at once). As soon as you press the second button will reset the odometer
  3. onall displays immediately show up 888888 and then in the display window will display the currently selected calibration factor constant k of the vehicle. During this time, press the F1 key 3 times and then OK - they are just 4 seconds. When you do, wait and on the display Conf
  4. If you wait too long and starts to repeat the measurement point. 1 - 4

configuration menu

after menu move by pressing the F1 key to enter the function with

theOK button. , The change make by pressing F1 and confirm

with OK. Parameter change is confirmed by a flash of the display.

Exitparameter setting performed by pressing CLR. From the menu to the normal operating mode

also go out CLR button which will restart tripmeter, save

thesettings and start measuring mode.

Available settings are:

  1. Units - is displayed on the display UNIT - selection of units which will be presented measurements of the road - miles and miles
  1. meter -metric system
  2. imp- a system of imperial (ny) or English
  1. pulses - the display shows the IMPS - dialing mode - with the pulses of the road and only GPS or
  1. GPS-and-off- work with only the GPS system - measuring is done only from 5 km / h
  2. and-on - work using pulses obtained from the road car or an additional sensor and GPS system - this measurement provides the most accurate
  1. GPS d - on / off GPS participate in calculating way
  1. off - odometer will work only with the pulse of the wheels
  2. on - GPS will support road charging
  1. DIST - default parameter settings displayed during startup mode. List of abbreviations below.
  1. First, using the F1 set the parameter window A, you accept the OK button, then set the parameters of the window B and C. OK zatwordza settings.
  1. STAGE - default parameter settings displayed during startup mode. List of abbreviations below.
  1. As 4.1.
  1. REG - default parameter settings displayed during startup mode. List of abbreviations below.
  1. As 4.1.

List of abbreviations measured parameters

  1. TRIP - way
  2. short-TRIP- way short left to drive
  3. Trip2 - way short no. 2
  4. ODO -  road
  5. long-ODO- the road to drive long rest
  6. stop - the time from the start mode, eg STAGE - time OS or DIST and REG - the time from the start
  7. timer - the time from the start or the time remaining when the mode STAGE or DIST before the start enter the time portion of the rally
  8. Bat - supply voltage
  9. FUEL - fuel
  10. [GPS] Sat - number of visible GPS satellites
  11. [GPS] HIGH - altitude
  12. [GPS] Trac - course
  13. [reg] AVG Ti - profit or loss, expressed in time - resolution 0.1 seconds
  14. [reg] AVG Tr - profit or loss expressed by - Resolution You 10 meters
  15. [reg] AVG Speed ​​- the actual average speed difference from the ideal - resolution of 0.1 km / h

When all values ​​when we are in the main branch, press CLR. Long beep and reset the tripmeter indicates the setting.

Configuration distance measurement

calibration factor of the vehicle.

This is the number of pulses counted from the vehicle corresponding to the crossing 1,000 m  

measured ratio can be:

calibration factor - the measurement.

metromierzu there is the possibility of measuring the number of pulses for the stretch of road of any length. To start the measurement must be in the position of the home screen, press and hold the 6 and then additionally press 1 The appearance of the 0-values ​​confirms the launch function.

Now:

CLR clears the measured values ​​and immediately begin recounting

OK saves the measurement. To save the measured value press the button with the number you wish to register a factor.

Manufacturing method - Film: http://www.rajdowe-haldy.pl/wsparcie/video-instrukcje.html

calibration factor - typing

When the calibration factor is known it is possible to enter its value to the odometer. To start typing in a position to be the home screen, press and hold the button 5 and then additionally press 1 The appearance of the 0-values ​​confirms the launch function.

Now:

Enter using the keypad coefficient and then press OK to save the value, then enter the calibration memory into which you save the entered value. Press OK to finish.

Manufacturing method - Film: http://www.rajdowe-haldy.pl/wsparcie/video-instrukcje.html

selection of the calibration factor

to the calibration factor was active, select it from memory. Selecting the aspect ratio is stable - it will be used for calculation until you select a different value.  

To make a choice:

  1. Bring the appearance of the home screen that is ______ on all displays, by pressing the CLR button for 6 seconds. (If you see ______ it means that you are in the start screen and you skip this step)
  2. Press and hold the F1 as long as the string goes out DIST ie the ability to select the mode. Continue to hold down the F1
  3. for the help of the buttons marked with numerals browse coefficient memory (momentary pause in pressing the buttons will show the value of the memory cell)
  4. When you find the factor by which you plan the measurement, release the F1 key

measurements will be continued by the new calibration factor.

Manufacturing method - Film: http://www.rajdowe-haldy.pl/wsparcie/video-instrukcje.html

Measurement configurationfuel

consumption measurement is performed by measuring and recalibration of the indications of the original fuel level sensor in a vehicle or by using an additional probe if fitted. Measurement accuracy is dependent on the accuracy of float or probe can be determined, however it is not worse than + / 2 dm3 for the fuel tank is not greater than 100 dm3.

Consumption measurement functions can be called only when conditions are met: on the ignition (on the yellow wire is the voltage) and vehicle speed less than 2 km / h

To display were presented in liters must perform calibration as described below. Calibrations preferably performed on the fuel station, starting from a maximum of an empty tank.

Factor fuel metering

for accurate measurement Once you have set the rate of fuel consumption measurement. Entering fuel ratio measurement is possible by pressing the [COR] and [FUEL]. The bottom window shows the current value, and the upper field to enter a new value. For most vehicles, type a value of 1000 or contact us. After entering the new value, press [OK]. The display flashes a sign store of value.

Calibration - the measurement

from the starting position tripmeter, press [INFO] and [FUEL]. Upper window shows the measured value tripmeter.

Subscribe value and then it refuel.

Repeat the process until you fill the tank. Well, that between successive portions of the fuel dolewanego take breaks to cessation of the fuel.

Use the [CLR] go out to the starting position.

Measurement do with tables as below, sorting measurements of the tripmeter cumulative

Position

Displacement

Indication tripmeter

1

1

560

2

25

356

-

10

55

120

Calibration can be a maximum of 10 points, so the tank capacity divided by 10 gives us the size of a single portion of fuel.  

calibration - typing

from home position tripmeter, press [MEMORY] and [FUEL].

in the upper window, enter the level of fuel in liters Press [OK], the entered value jumps to the bottom of the window. In the upper window, enter the measured value corresponding to your entry level tripmeter fuel., And press [OK.].

Repeat until you have entered all calibration points. As soon as you enter the last point calibration and will appear in the upper window 0 as an incentive to enter the next step. press [CLR]. The device comes with features typing, storing calibration and goes to the window to enter the fuel measurement values. Enter a factor as in the first step. After entering values, press [OK]. Calibration is saved. The display flashes a sign store of value.

Ride on the regularity

does not require additional configuration settings.


Operation

Selection modes

to choose from we have 3 options:

From the home screen press the F1 key. The window shows the name of the mode. Repeatedly press the F1 switch selectable modes. You accept the OK button.

Name Mode

DiodeMode

Application

Switching

DIST

LED LightsDIST.

When you need to measure and quickly delete TRIP way short

of the start screen you can activate this mode measurements in succession by pressing [F1] and then press [OK] then appears on the screen DIST is displayed.

STAGE

STAGE LED lights.

when you need to measure lap times Stopwatch

from the start screen you can activate this mode measurements in succession by pressing [F1] and then press [OK] when the screen appears STAGE.

Regularity

No LED

when need

to cross section

of the setspeed

average

from the start screen you can activate this mode measurements in succession by pressing [F1] and then press [OK] when the screen appears REG

Countdown parameters of selected values

​​tripmeter has the ability to deduct the value of the parameter selected values. Always when starting or continuing measurements measurements started in a different mode, enter the odometer will allow parameters to count. If you do not want to use the countdown, skip the next screen by pressing the [OK] button until you see zeros and their flashing which means readiness to take off.

Parameters that may be counting down to:

Time Timer (time to go from PKC to the next PKC)

Road ODO ( way of PKC to PKC)

Road TRIP (road OS)

1

When we start measuring mode DIST

2

When we start measuring mode STAGE

3

When we start measuring

mode Regularity

4

continues STAGEWhen measuring

5

When the distance measurements continued

        

introduction of road overall - ODO

In the upper window appears incentive to enter the road from PKC to PKC. Using the keypad, which currently acts as a keyboard only numeric type values ​​to the nearest meter, so the value of 12800 m, type: [1], [2], [8], [0], [0], [OK].

introduction of the section OS - TRIP

In the upper window, there is an incentive to enter the road OS. Using the keypad, which currently acts as a keyboard only numeric type values ​​to the nearest meter, so the value of 6400 m, type: [6], [4], [0], [0], [OK].

The introduction of time - Timer

in the upper window appears encouragement to enter time spent on passing episode. Using the keypad, which currently acts as the numeric keypad, enter the time only provided to overcome the way of PKC PKC to the next and press [OK]. Enter the time in hh: mm: ss

Enter the start delay DELAY.

DELAY parameter allows you to boot tripmeter earlier than the actual start, and the measurements will start automatically after DELAY time. This time may be up to 60 seconds. You can enter DELAY time before the start of each measurement, no matter whether we start measurement or continue with another mode.

Appears in the upper window, the incentive to enter the DELAY time. Enter a value from the keyboard, for example, 30 seconds. The introduction of 30 seconds is pushing to [3], [0], [OK].

Start measurement starts then 30 seconds after booting tripmeter.

Countdown in days drive parameters regularity (Regularity)

mode before Regularity section, you must enter expected by the organizers average speed section. Average speed is introduced with an accuracy of two decimal places. Due to the lack of a comma on the keyboard, enter the value ignoring the sign

speed40.12 km / h, enter as 4012.

After entering the set average speed and accepting the [OK] button. Odometer flashes a sign of readiness to take off. After pressing [F1] and start measuring the displays show the display mode configured for Regularity, eg

parameters calculated and stored in the memory

for each mode are calculated parameters that can be read from the odometer when finished measurement in one of the modes and not have started another, by pressing MEMORY (only when you are between the modes and the displays lit horizontal line).

Film: http://www.rajdowe-haldy.pl/wsparcie/video-instrukcje.html

list of parameters stored in the memory

[ TOP SPEED] speed

[AVERAGE SPEED] mean velocity

[Stopwatch] time travel episode

[TRIP] road section

[TIMER] travel time of the earlier sections - the parameter is calculated continue

[ODO] dear total of all previous sections - the parameter is calculated continue

Waiting for measurement start

flashing on the display digits 0 is ready to take off. Tripmeter start measurements by pressing F1 (if you entered DELAY time it will be first deducted)

Additional

measurements.functions (action key) - STAGE mode

[F1] - start counting / calculating - (after starting changing their destiny and acts as a start / stop measurement time).

[TRIP] - road section - (pressed short - shows the distance traveled during the OS mode. Pressing [TRIP] shows the way to the end of the episode quickly, which entered the road - the distance traveled. Pressing the [TRIP] restores the previous indication) .

[VOLT] - mains voltage of the vehicle - (shown in the top window supply voltage tripmeter. On the first display field showing the letter U, which indicates that it is a voltage).

[Stopwatch] - time line - leading measurement - (restores STOPWATCH indication if introduced upper display in another state).

[FUEL] - the amount of fuel in the tank - (pressed short - shows the fuel. condition must be fulfilled speed of less than 2 km / h Subsequent to restore the previous indication.)

[FREEZE] (pressed long - to stop all functions and freezing tripmeter. Flashing quickly while all the LEDs near the top of the display).

[LAP TIME] (pressed briefly - for you to stop for 10 seconds without stopping display indications measurement. pressed again to unlock the display. If you do not unlock using the display after 10 seconds since the introduction of the state of [LAP TIME], displays unlock automatically. Such a state is indicated by a blinking LED [LAP TIME]).

[LIGHT] ( pressed briefly - every time dims the display by one step, until the minimum brightness. Subsequent presses will cause abrupt brightening of the display).

[LIGHT] (pressed long - will immediately extinguish the displays and LEDs RUN inflammation.

When the displays are dimmed, all keys brightness gain to restore functionality to the level from which wygasiliśmy quickly. This is only one press. When the displays have lit keys work normally).

[TRACK] - course - (pressed short - shows the course if you have connected a GPS. On the first box to the left illuminates the degree sign).

[INFO] (pressed short - illuminates for 1 second subtitle informing what is displayed in the window).

[ODO] - the road overall - (pressed short - shows the distance traveled since the start time of timer. further short press shows-way entered - ODO. Subsequent short to restore the previous indication.)

[TIMER] - time remaining until the next TC - (restores the TIMER indication if introduced lower display in another state).

[SPEED] - speed - (pressed short - shows the current speed. On the first box to the left lights up the letter S. Another short press shows the average speed from the beginning section. During the first field on the left is lit Sr. further short press shows the maximum speed achieved since the beginning of the episode. During the first field on the left is lit ST.)

In the case of accidentally pressing [F1] to stop the measurement, press the re-start another measurement.

Description of functions (action key) - disance mode

[F1] - clears the way TRIP and immediately starts the measurement.

[VOLT] - mains voltage of the vehicle - (shown in the top window supply voltage tripmeter. On the first display field showing the letter U, which indicates that it is a voltage).

[TRIP] - the road segment - leading measurement - (restores TRIP way if the display was in another state. Pressed long - delete indication and turns off completely functions Trip2) . When pressed short - will call on the lower display the second kasowalnego meter road. Calling the road Trip2 is synonymous with the start of counting. [F2] key takes on the functionality of clearing the road and immediately start measuring.

[Trip2] pressed briefly - when the road Trip2 is displayed on the lower display stops measurement (if it is not presented in this press [Trip2] invokes the function on the display, and another press stops the measurement ), again a short press [Trip2] restarts the measurement.

[Stopwatch] - lap - (Stopwatch shows the time from the beginning of the line (for calculating road TRIP)).

[FUEL] - the amount of fuel in the tank - (pressed short - shows the fuel. Must condition to be satisfied speeds of less than 3 km / h Subsequent to restore the previous indication.)

[FREEZE] pressed long - to stop all functions and freezing tripmeter. Blink quickly while all the LEDs near the top of the display.

[LAP TIME] (pressed briefly - to stop for 10 seconds without stopping displays indications of measurement. Pressed again to unlock the display. If you do not unlock using the display after 10 seconds since the introduction of the state of the LAP TIME displays unlock automatically. Such a state is indicated by a blinking LED [LAP TIME]).

[LIGHT] (pressed briefly - every time dims the display by one step, until the minimum brightness. Subsequent presses will cause abrupt brightening of the display. pressed long - will immediately extinguish the displays and LEDs RUN inflammation. When the displays are dimmed, all buttons become functional restoration of brightness to a level from which wygasiliśmy quickly. This is only one press. When the displays have lit keys work normally.)

[TRACK] - exchange - (pressed short - shows the course if you have connected a GPS. In the first box to the left lit degree mark.)

[INFO] (pressed short - illuminates for 1 second subtitle indicating what is displayed in the window).

[ODO] - the road overall - (pressed short - shows the distance traveled since the start of time TIMER . further short press shows the path entered - ODO. Subsequent short to restore the previous indication.) When pressed long - erases the road ODO and the simultaneous deletion of the road TRIP).

[COR] (pressed long - brings up the road on the lower display ODO. Rozmyślimy If you press the [COR] and return to what it was before the call. If we called ODO and we want to correct and press [OK]. (key does not work now as Trip2). ODO flashes. Use the keypad to enter a new value ODO and press OK. New ODO shows up in the bottom window appears in the upper road TRIP and its value is reset. keys while running the option COR).

[SPEED] - speed - (pressed short - shows the current speed. On the first box to the left lights up the letter S. Another short press shows the average speed from the beginning of the episode. During the first field on the left is lit the Sr. further short press shows the maximum speed achieved since the beginning of the episode. During the first field on the left is lit ST).

[TIMER] - the time remaining to the next TC - (pressed short - restores TIMER indication on the display or indication STOPWATCH when starting mode DISTANCE not I set the timer).

[2] (pressed briefly changes the direction of calculation as well as the inclusion of reverse when there is no road TRIP  Additional

2).functions (action key) - Regularity mode

[F1] - Start Mode - (after the start mode loses its properties)

[TRIP] - road section - (pressed short - shows the distance traveled since the start mode. Pressing the [TRIP] shows profit or loss (if it displays "-" in front of the result) to an accuracy of 10m to the road traveled with a set average speed. Pressing the [TRIP] restores the previous indication.)

[VOLT] - mains voltage of the vehicle - (shown in the top window supply voltage tripmeter. On the first display field showing the letter U, which indicates that it is a voltage).

[STOPWATCH ] - lap - (Shows the time in walk distance from the start of the measurements. pressed again shows the profit or loss (if it displays "-" in front of the result) for travel time in walking with the set average speed).

[FUEL] - the amount of fuel in the tank - (pressed short - shows the fuel. condition must be fulfilled speed of less than 3 km / h Subsequent to restore the previous indication.)

[FREEZE] (pressed long - to stop all functions and freezing tripmeter. flashing quickly while all the LEDs near the top of the display) .

[LAP TIME] (pressed briefly - for you to stop for 10 seconds without stopping the display displays the measurement. pressed again to unlock the display. If you do not unlock using the display after 10 seconds since the introduction of the state of [LAP TIME], displays unlock automatically. This condition is indicated by a blinking LED [LAP TIME]).

[LIGHT] (pressed briefly - every time dims the display by one step, until the minimum brightness. Subsequent presses will cause abrupt brightening of the display).

[LIGHT] (pressed long - will immediately fade displays and LEDs RUN inflammation.

When the displays are dimmed, all keys become functional restoration of brightness to a level from which wygasiliśmy quickly. This is only one press. When displays have lit keys work normally).

[TRACK] - course - (pressed short - shows the course if you have connected a GPS. On the first box to the left illuminates the degree sign).

[INFO] (pressed short - illuminates for 1 second subtitle indicating what is displayed in the window).

[ODO] - total road - (pressed short - shows the distance traveled since the start time of timer. Subsequent long press clears the ODO.)

[TIMER] - total time-(restores the TIMER indication if introduced lower display in another state).

[SPEED] - speed - (pressed briefly - shows the current speed. In the first box to the left lights up the letter S. Another short press shows the average speed since the beginning of the episode. In the first field on the left is lit Sr. Another short press shows the maximum speed achieved since the beginning of the episode. In the first field on the left is lit ST. Another press shows profit or loss (if displays "-" in front of the result) to set the average speed.)

End measurements - viewing of the

DISTANCE mode

after pressing the [OK] long finally finish the possibility of continuing measurement in this mode. Do not delete a charging timer and ODO.

You can now

by next pressing the [MEMORY], read out a way for the section:

  1. maximum speed
  2. average speed traveled segment
  3. of travel time [Stopwatch]
  4. path [TRIP] (ie, the sum of the deleted sections)
  5. time [TIMER] which still counts
  6. the road [ODO] which still counts

when displaying values ​​from memory MEM LED is lit. Descriptions displayed on the values ​​of the left side of the display. Indications present in these windows, which are imaged during the

measurements.,Or by pressing [MODE] to select the mode in which you continue to rally. You can select STAGE DISTANCE or Regularity. You can do this before or after the reading of

memory!,Or by long pressing [CLR] to exit screen.

STAGE Mode

After stopping time by pressing the F1 key is pressed [OK] long finally finish the possibility of continuing measurement in this mode. Do not delete a charging timer and ODO.

You can now

by next pressing the [MEMORY], read out a way for the section:

  1. maximum speed
  2. average speed traveled segment
  3. of travel time [Stopwatch]
  4. path [TRIP] (ie, the sum of the deleted sections)
  5. time [TIMER] which still counts
  6. the road [ODO] which still counts

when displaying values ​​from memory MEM LED is lit. Descriptions displayed on the values ​​of the left side of the display. Indications present in these windows, which are imaged during the

measurements.,Or by pressing [MODE] to select the mode in which you continue to rally. You can select STAGE DISTANCE or Regularity. You can do this before or after the reading of

memory!,Or by long pressing [CLR] to exit screen.

Regularity mode

after pressing the [OK] long finally finish the possibility of continuing measurement in this mode. Do not delete a charging timer and ODO.

You can now

by next pressing the [MEMORY], read out a way for the section:

  1. maximum speed
  2. average speed traveled segment
  3. of travel time [Stopwatch]
  4. path [TRIP] (ie, the sum of the deleted sections)
  5. time [TIMER] which still counts
  6. the road [ODO] which still counts

when displaying values ​​from memory MEM LED is lit. Descriptions displayed on the values ​​of the left side of the display. Indications present in these windows, which are imaged during the

measurements.,Or by pressing [MODE] to select the mode in which you continue to rally. You can select STAGE DISTANCE or Regularity. You can do this before or after the reading of

memory!,Or by long pressing [CLR] to exit screen.


Technical and operational


Warranty

Warranty is for a period of 60 months from the date of saledevice.Warranty

will be considered only in case of use of the product for its intended purpose. Warranty against defects in the product to prevent its further use as intended. Are not subject to warranty defects resulting from mechanical damage, alteration, normal wear items, etc.

The warranty is valid only with proof of purchase.

Name and Type: ........................................................

Date of sale : ..................................................

number: ...............................................

instructions

to download from the website: http:/ / rajdowe-haldy.pl/wsparcie/instrukcje.html